• Journal of Trauma and Injury
• /
• 제31권2호
• /
• pp.66-71
• /
• 2018

Patients with traumatic aortic rupture rarely reach the hospital alive. Even among those who arrive at the hospital alive, traumatic aortic rupture after high-speed motor vehicle accidents leads to a high in-hospital mortality rate and is associated with other major injuries. Here, we report a rare case of descending midthoracic aortic rupture with blunt diaphragmatic rupture. Successful management with emergency laparotomy after an immediate endovascular procedure resulted in a favorable prognosis in this case.

• 소성∙가공
• /
• 제15권2호
• /
• pp.143-147
• /
• 2006

Effect of processing condition on the hot extrusion of Al-Zn-Mg-Sc alloy was investigated. For this purpose, hot compression test and FE-simulation were conducted via Thermecmaster-Z and DEFORM-3D, respectively. The microstructure evolution during hot extrusion and post heat-treatment was investigated and deformation mechanisms were analyzed by constructing processing map. FE-simulation results show that the temperature difference between container and billet has considerable influence on the final shape of extruded T-shape bar. The relation between applied load and processing time was predicted by the FE-analysis as well as punch speed vs. stroke chart.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.389-391
• /
• 2014

The Vibration Analysis of Rotating Inward Beams Considering The Tip-Mass is presented based on Euler-Bernoulli beam theory. The frequency equations, which are coupled through gyroscopic coupling terms, are calculated using hybrid deformation variable modeling along with the Rayleigh-Ritz assumed mode methods. In this study, resulting system of ordinary differential equations shows the effects of angular speed, and Young's modulus ratio. It is believed that the results will be a reference with which other researchers and commercial FE analysis program, ANSYS can compare their results.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.123-128
• /
• 2012

The responses of a bridge due to a moving vehicle are obtained analytically by modeling a vehicle as a constant point force. From the results it is found that the responses after a vehicle leaves the bridge become very small for some speeds of a vehicle. When a vehicle is modeled as a two dof system for a more accurate analysis, the same phenomenon is observed while the roughness of the bridge is small. Determining the fundamental frequency of a bridge so that one of the above speeds coincides with a frequent speed of vehicles, the responses of a bridge can be minimized.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.182-184
• /
• 2001

Linear pulse Motor(LPM) are used a field where smooth linear motion is required, and it's position accuracy higher than that of a lead. According to the advantage such as simplicity of mechanical frame, high reliability, precise open_loop operation, low inertia etc LPM is applied largely where it have made motor of this kind more and more attractive in many application areas such as factory automation and high speed positioning. This paper is researched to analyze for thrust force characteristic of hybrid LPM. Both the thrust and normal force are very sensitive to the airgap and tooth pitches of the force and platen. To find the optimal design parameter on the hybrid LPM for the embroidery machine. For the field analysis, the finite element method(FEM) is employed for calculating the force. The reluctance models will be used the magnetic permeance of airgap under static-conditions. The forces between forcer and platen have been calculated using the virtual work mathod.

• Journal of Magnetics
• /
• 제14권2호
• /
• pp.97-100
• /
• 2009

A new eddy current testing probe was developed to separate the eddy current signal distortion caused by permeability variation clusters and ordinary defects created in steam generator tubes. Signal processing circuits were inserted into the probe to increase the signal-to-noise ratio and allow digital signal transmission. The new probe could measure and separate the magnetic phases created in the steam generator tubes in the operating environment of a nuclear power plant. Furthermore, the new eddy current testing probe can measure the defects in steam generator tubes as rapidly as a bobbin probe with enhanced testing speed and reliability of defect detection.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.369-374
• /
• 2004

Nowadays, the more speedy and functional railway vehicles are required by customers, the more broad boundary conitions of train's running are present. At this condtion, it is difficult for the traditional concept of suspension system which has the constant characteristics dependant on the running condition to meet the advenced requirements such as high ride quality. So, the active suspension should be designed to supplied the optimized suspensnion condition actively and to perform the optimal ride quality on the irregula running condition such as on the enterance or exitance of the tunnel or on the crossing the high speed train each others. On this study, the train dynamic model, integration of active suspension system, and the control logic would be proposed, and the advanced performace of train would be shown though the simulation tests.

• Transactions on Electrical and Electronic Materials
• /
• 제5권6호
• /
• pp.233-236
• /
• 2004

Copper metallization has been used in high-speed logic ULSI devices instead of the conventional aluminum alloy metallization. One of the key issues in copper CMP is the development of slurries that can provide high removal rates. In this study, the effects of slurry chemicals and pH for slurry dispersion stability on Cu CMP process characteristics have been performed. The experiments of copper slurries containing each different alumina and colloidal silica particles were evaluated for their selectivity of copper to TaN and $SiO_{2}$ films. Furthermore, the stability of copper slurries and pH are important parameters in many industries due to problems that can arise as a result of particle settling. So, it was also observed about several variables with various pH.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 B
• /
• pp.435-437
• /
• 1998

In this productive system, it needs to control the each axis motion harmoniously to perform accurately for the manufacturing, transporting and printing. Independent Axis Control usually used for this objection. However, if Independent Axis Control mismatched the parameter of each axis system or in the case of free curve tracking or the case of high speed control, there would be big contour error so that cannot achieve control objection. As a result, there is Contour Control method suggested to supply for this defect. This paper carried modeling of biaxial system and implemented Independent Axis Control & Contouring Control on straight line, circular, and coner path by simulation and experiment. If feedrate increased, contour error growed. In consequence, according to this factor, we introduced contouring controller, so we could find the fact that contour error was reduced more than that of independent axis control about each path.

• 대한기계학회논문집B
• /
• 제28권11호
• /
• pp.1359-1367
• /
• 2004

The demand of vacuum pump has been increased in the process of semi-conduct manufacturing, as a core component. The response of the system for vacuum pump performance test can be utilized to assess the system and to obtain the reliability of the apparatus for the test. The system consists of gas supply tank, pressure chamber, measurement chamber and transmission line. Transient analysis for compressible fluid has been conducted to evaluate the dynamic characteristic of the volume terminated transmission line. Numerical approach based on the method of characteristics is used for the analysis. The response is evaluated with the important parameters for the system: i.e., length and diameter of the line, volume of the terminal tank. Using the numerical results, pumping speeds are calculated and then compared to the experimental results.