• Computers and Concrete
• /
• v.33 no.3
• /
• pp.241-250
• /
• 2024

This article investigates the thermal and post-buckling problems of graphene platelets reinforced metal foams (GPLRMF) beams with initial geometric imperfection. Three distribution forms of graphene platelet (GPLs) and foam are employed. This article utilizes the mixing law Halpin Tsai model to estimate the physical parameters of materials. Considering three different boundary conditions, we used the Euler beam theory to establish the governing equations. Afterwards, the Galerkin method is applied to discretize these equations. The correctness of this article is verified through data analysis and comparison with the existing articles. The influences of geometric imperfection, GPL distribution modes, boundary conditions, GPLs weight fraction, foam distribution pattern and foam coefficient on thermal post-buckling are analyzed. The results indicate that, perfect GPLRMF beams do not undergo bifurcation buckling before reaching a certain temperature, and the critical buckling temperature is the highest when both ends are fixed. At the same time, the structural stiffness of the beam under the GPL-A model is the highest, and the buckling response of the beam under the Foam-II mode is the lowest, and the presence of GPLs can effectively improve the buckling strength.

• Earthquakes and Structures
• /
• v.26 no.4
• /
• pp.251-259
• /
• 2024

In this paper, the thermal post-buckling behavior of graphene platelets reinforced metal foams (GPLRMFs) plate with initial geometric imperfections on nonlinear elastic foundations are studied. First, the governing equation is derived based on the first-order shear deformation theory (FSDT) of plate. To obtain a single equation that only contains deflection, the Galerkin principle is employed to solve the governing equation. Subsequently, a comparative analysis was conducted with existing literature, thereby verifying the correctness and reliability of this paper. Finally, considering three GPLs distribution types (GPL-A, GPL-B, and GPL-C) of plates, the effects of initial geometric imperfections, foam distribution types, foam coefficients, GPLs weight fraction, temperature changes, and elastic foundation stiffness on the thermal post-buckling characteristics of the plates were investigated. The results show that the GPL-A distribution pattern exhibits the best buckling resistance. And with the foam coefficient (GPLs weight fraction, elastic foundation stiffness) increases, the deflection change of the plate under thermal load becomes smaller. On the contrary, when the initial geometric imperfection (temperature change) increases, the thermal buckling deflection increases. According to the current research situation, the results of this article can play an important role in the thermal stability analysis of GPLRMFs plates.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1444-1447
• /
• 2004

For the OLED evaporation process, thin film thickness uniformity is of great practical importance. In order to achieve the better thickness uniformity, geometric simulation of film thickness distribution profile is required. In this paper, a geometric modeling algorithm is introduced for process simulation of full-color OLED evaporating system. The physical fact of the evaporation process is modeled mathematically. Based on the developed method, the uniformity of the organic layer thickness can be successfully controlled.

• Structural Engineering and Mechanics
• /
• v.90 no.4
• /
• pp.357-370
• /
• 2024

Due to the fact that the mechanism of the effects of temperature and initial geometric imperfection on low-velocity impact problem of axially moving plates is not yet clear, the present paper is to fill the gap. In the present paper, the nonlinear dynamic behavior of axially moving imperfect graphene platelet reinforced metal foams (GPLRMF) plates subjected to lowvelocity impact in thermal environment is analyzed. The equivalent physical parameters of GPLRMF plates are estimated based on the Halpin-Tsai equation and the mixing rule. Combining Kirchhoff plate theory and the modified nonlinear Hertz contact theory, the nonlinear governing equations of GPLRMF plates are derived. Under the condition of simply supported boundary, the nonlinear control equation is discretized with the help of Gallekin method. The correctness of the proposed model is verified by comparison with the existing results. Finally, the time history curves of contact force and transverse center displacement are obtained by using the fourth order Runge-Kutta method. Through detailed parameter research, the effects of graphene platelet (GPL) distribution mode, foam distribution mode, GPL weight fraction, foam coefficient, axial moving speed, prestressing force, temperature changes, damping coefficient, initial geometric defect, radius and initial velocity of the impactor on the nonlinear impact problem are explored. The results indicate that temperature changes and initial geometric imperfections have significant impacts.

• Journal of Korean Society for Quality Management
• /
• v.27 no.4
• /
• pp.143-152
• /
• 1999

In Shewhart control chart, the average run length(ARL) is calculated using the mean of a conventional geometric distribution(CGD) assuming a sequence of identical and independent Bernoulli trials. In this, the success probability of CGB is the probability that any point exceeds the control limits. When the process is in-control state, there is no problem in the above assumption since the probability that any point exceeds the control limits does not change if the in-control state continues. However, if the out-of-control state begins and continues during the process, the probability of exceeding the control limits may take two forms. First, once the out-of-control state begins with exceeding probability p, it continues with the same exceeding probability p. Second, after the out-of-control state begins, the exceeding probabilities may very according to some pattern. In the first case, ARL is the mean of CGD with success probability p as usual. But in the second case, the assumption of a sequence of identical and independent Bernoulli trials is invalid and we can not use the mean of CGD as ARL. This paper concentrate on that point. By adopting one generalized binomial distribution(GBD) model that allows correlated Bernoulli trials, generalized geometric distribution(GGD) is defined and its mean is derived to find an alternative ARL when the process is in out-of-control state and the exceeding probabilities take the second form mentioned in the above. Small-scale simulation is performed to show how an alternative ARL works.

• Communications of the Korean Mathematical Society
• /
• v.14 no.3
• /
• pp.627-633
• /
• 1999

Let the given distribution $\pi$ have a log-concave density which is proportional to exp(-V(x)) on $R^d$. We consider a Markov chain induced by the method Gibbs sampling having $\pi$ as its in-variant distribution and prove geometric ergodicity and the functional central limit theorem for the process.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2006.05a
• /
• pp.156-159
• /
• 2006

In order to design an evaporation system, geometric simulation of film thickness distribution profile is required. In this paper, a geometric modeling algorithm is introduced for process simulation of the evaporating process. The physical fact of the evaporating process is modeled mathematically. Based on the developed method, the thickness of the thin-film layer can be successfully controlled.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.7
• /
• pp.23-33
• /
• 1996

This paper deals with the design of a recursively-indexed binary code for facsimile soruces and its performance. Sources used here are run-lengths of white pixels form higher-resolution facsimile. The modified huffman code used for G.3 facsimile is chosen for the performance comparison. Experiments confirm the fact that recursive indexing preserves the entropy of a memoryless geometric source: the entropy of recursively-indexed physical surce iwth roughly geometric distributin remains within 2% of the empirical source entropy. The designed recursively-indexed binary codes consist of a code applied to text-type documents and to graphics - type documents is compared iwth that of the modified huffman code. Numerical resutls show that the modified huffman code performs well for text-type documents and not equally well for graphics-tyep documents. On the other hand, recursively-indexed binary codes have shown a better performance for graphics-type documents whose distribution are similar to a geometric distribution. Specifically, the code rates of recursively-indexed binary codes with 60 codewords are from 8% to 20% of the empirical source entropy smaller than that of th emodified huffman code with 91 codewords.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.3
• /
• pp.113-123
• /
• 1989

We developed a general algorithm and program to determine nominal value of new optimum geometric parameters of MOSFET when yield satisfying specification of drain current and noise spectral density is maximum. In this paper, the total number of considered devices is 500, and each parameters of geometric parameter was generated randomly within the limits of ${pm}3%$ of nominal value, and the distribution of 500 geometric parameters is gaussian distribution.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.3
• /
• pp.5-12
• /
• 2002

Hydraulic conductivity k is one of the most important engineering properties of soil. However, both field and laboratory procedures fur the determination of k are often tedious and expensive. This paper presents new models to predict k using statistical parameters from grain size distribution. A number of permeability tests far 36 types of sands mixed based on statistics were conducted to develop the regression-based models. Parameters used to estimate k are both the geometric mean and geometric standard deviation of the soil samples, or the particle-size distribution curve parameters such as D_{10},D_{50},D_{60}. Hydraulic conductivity predicted by this model is in good agreement with the laboratory measurements fir the soil samples obtained at 20 locations within the Korean Peninsula. The performances of the proposed models were also compared with those of existing models including Hazen's.