• 한국안전학회지
• /
• 제13권1호
• /
• pp.85-91
• /
• 1998

Sol-gel derived silica films were prepared by dip-coating onto polymethylmethacylate with Tetraethoxysilane(TEOS) as starting materials. Film properties such as viscosity and thickness were investigated as a function of dip speed, waterprecursor ratio, sol aging time. IR spectra of the gel films prepared from TEOS at various R are given. At small values of R the absorption peaks assignable to C-H vibration in $-OC_2H_5$ groups are observed around 3000 and 1500-1300 $cm^{-1}$. These bands indicate that the -$-OC_2H_5$ groups are retained in the gel at small values of R because of incomplete hydrolysis of TEOS. Film behaviour was interpreted in terms of the dependence of hydrolysis and condensation rates on the interplay between sol pH and waterprecursor ratio. Film thickness was found to increase by approximately a factor of two as waterprecursor ratio increased from two to six. Film thickness also increased with sol prepolymerization time. Surface quality was correlated with processing conditions.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권10호
• /
• pp.983-988
• /
• 1997

We investigated the structural and dielectric properties of PZT(20/80)/PZT(80/20) heterolayered thin films that fabricated by the alkoxide-based Sol-Gel method. PZT(20/80)/PZT(80/20) heterolayered thin films were spin-coated on the Pt/Ti/SiO$_2$/Si substrate with PZT(20/80) film of tetragonal structure and PZT(80/20) film of rhombohedral structure by turns. Each layers were dried to remove the organic materials at 30$0^{\circ}C$ for 30min and sintered at $650^{\circ}C$ for 1hr. This procedure was repeated several times to form PZT(20/80)/PZT(80/20) heterolayered films and thickness of the film obtained by one-times of drying/sintering process was approximately 80-90nm. PZt-1, 3, 5 films with top layer of PZT(20/80) film of tetragonal structure showed fine grain structure and PZT-2, 4, 6 films with top layer of PZT(80/20) film of rhombohedral structure showed the dense grain microstructure without rosette-type. Dielectric constant and dielectric loss of the PZT-6 film were approximaterly 1385 and 3.3% respectively. Increasing the number of coatings remanent polarization was increased and coercive field was decreased and the values of the PZT-6 film were 8.13$\mu$C/cm$^2$and 12.5kV/cm respectively.

• 한국정보통신학회논문지
• /
• 제9권7호
• /
• pp.1491-1496
• /
• 2005

[ $Pb_{0.72}La_{0.28}TiO_3$ ] (PLT(28)) 박막을 sol-gel 법을 이용하여 제작한 후, 그 특성을 조사하여 ULSI DRAM 의 캐패시터 절연막으로서의 적용 가능성을 연구하였다. Sol-gel 법의 출발 물질로는 acetate 계를 사용하였다. TGA-DTA 분석을 통하여 PLT(28) 박막의 sol-gel 법에 의한 공정 조건을 확립하였다. 매 coating 후 $350^{\circ}C$ 에서 drying 하고, 마지막으로 $650^{\circ}C$ 에서 annealing 하여 $100\%$ perovskite 구조를 가지는 치밀하고 crack 이 없는 PLT(28) 박막을 얻었다. $Pt/Ti/SiO_2/Si$ 기판 위에 PLT(28) 박막을 형성하여 전기적 특성을 측정하였다. 그 결과 유전 상수와 누설전류밀도가 각각 936 과 $1.1{\mu}A/cm^2$ 으로 측정되었다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2005년도 추계종합학술대회
• /
• pp.865-868
• /
• 2005

$Pb_{0.72}La_{0.28}TiO_3$ (PLT(28)) 박막을 sol-gel 법을 이용하여 제작한 후, 그 특성을 조사하여 ULSI DRAM 의 캐패시터 절연막으로서의 적용 가능성을 연구하였다. Sol-gel 법의 출발 물질로는 acetate계를 사용하였다. TGA-DTA 분석을 통하여 PLT(28) 박막의 sol-gel 법에 의한 공정 조건을 확립하였다. 매 coating 후 350$^{\circ}C$에서 drying 하고, 마지막으로 650$^{\circ}C$에서 annealing 하여 100% perovskite 구조를 가지는 치밀하고 crack 이 없는 PLT(28) 박막을 얻었다. Pt/Ti/SiO$_2$/Si 기판 위에 PLT(28) 박막을 형성하여 전기적 특성을 측정하였다. 그 결과 유전 상수와 누설전류밀도가 각각 936 과 1.1${\mu}$A/cm$^2$ 으로 측정되었다.

• 반도체디스플레이기술학회지
• /
• 제13권1호
• /
• pp.91-95
• /
• 2014

(F,Ga) co-doped ZnO thin film on glass substrate was fabricated via a simple non-alkoxide sol-gel spin-coating. Contrary to the F single doped ZnO thin film, the (F,Ga) co-doped thin film showed a significant reduce in electrical resistivity after a second post-heat-treatment in reducing environment. The resulting decrease in electrical resistivity with Ga co-doping is considered to be resulted from the increases both carrier density and mobility. The optical transmittance of the (F,Ga) co-doped thin film in the visible range showed higher transmittance with Ga co-doping compared with F single doped ZnO thin film.

• 한국세라믹학회지
• /
• 제34권6호
• /
• pp.611-619
• /
• 1997

Optimal Mullite sol was synthesized by sol-gel process using Aluminium sec-butoxide(ASB), Tetraethoxysilane(TEOS) and then, Mullite films were dip-coated with various holding time in sol bath and heat-treated at 130$0^{\circ}C$ above for crystallization. The thickness of coated film increased linearly with holding time in sol bath and average pore size was controllable within 20~30$\AA$.

• Journal of Information Display
• /
• 제9권3호
• /
• pp.8-11
• /
• 2008

A novel non-alkoxide sol-gel process for synthesizing Ga-doped ZnO thin film on glass was derived for possible use as a transparent electrode in flat-panel displays, using zinc acetate dehydrate as the starting material. The structural and electrical properties of thin films have been characterized as functions of Ga addition and post-heat-treatments. Their carrier density, Hall mobility, and optical transmittance were measured and discussed herein to explain the characteristics of the sol-gel-derived Ga-doped ZnO thin film on glass.

• 한국전기전자재료학회논문지
• /
• 제29권9호
• /
• pp.527-531
• /
• 2016

In this study, p-type thin film transistors consisting of CuO channels were fabricated by sol-gel process, with copper (II) acetate monohydrate precursors. At $500^{\circ}C$, the deposited films were fully converted into monoclinic phase CuO. The fabricated CuO thin film transistors deliver field effect mobility in saturation regime of $0.015cm^2/Vs$, and $I_{on}/I_{off}$ of ${\sim}10^3$. The degradation of the performance of the fabricated CuO thin film transistor caused by the exposure to air has been studied.

• Journal of Information Display
• /
• 제10권1호
• /
• pp.24-27
• /
• 2009

A simple nonalkoxide sol-gel route for depositing an Al-doped ZnO thin film on a glass substrate was derived in this study. The initial Al dopant concentration in the sol-gel preparation varied and ranged from 0 to 5%. The sol-gel-derived thin films showed c-plane preferred crystallization of their hexagonal phase, with nanosized grain structures. First and second post-heat-treatments were carried out to improve the film’s electrical resistivity. The carrier density and the Hall mobility were measured and discussed to explain the electrical resistivity. The optical transmittance within the visible range showed compatible properties, which indicates the possible use of A1-doped ZnO as a transparent electrode in flat panel displays.

• 한국해양공학회지
• /
• 제29권1호
• /
• pp.94-99
• /
• 2015

Lead zirconate titanate (PZT) thick films with thicknesses of ㎛ were fabricated on silicon substrates using an aerosol deposition method. A PZT powder solution was prepared using a sol-gel process. The average diameters (d50) obtained were 1.67, 1.98, and 2.40μm when the pyrolysis temperatures were 300℃, 350℃, and 450℃ respectively. The as-deposited film had a uniform microstructure without any cracks or pores. The as-deposited films on silicon were annealed at a temperature of 700℃. The 20-㎛-thick PZT film showed good adherence between the PZT film and substrate, with no tearing observed in the conventional solid phase process. This was probably because the presence of pores produced from organic residue during annealing relieved the residual stresses in the deposited film.