• 대한기계학회논문집A
• /
• 제25권9호
• /
• pp.1475-1482
• /
• 2001

Nowadays reduction of gear noise in power transmission is very important, because the noise regulation is severe and demand of customer on noise is increased. To reduce gear noise, it is necessary to understand the noise characteristics of helical gear. In this work, we designed test rig for the study of gear noise and installed in semi-anechoic chamber. By using this rig, sound pressure level is measured under varying rotational speed and torque. The frequency characteristics of helical gear noise on the effect of lead errors and torque are discussed.

• 한국공작기계학회논문집
• /
• 제10권6호
• /
• pp.8-14
• /
• 2001

We develop a method to analyze dynamic behavior off multi-stage gear train system. The example system consists of three shafts supported by ball bearings at the ends of them and two pairs of spur gear set. For exact analysis, the meshing tooth pair of gear set is modeled as spring and damper having time-dependent meshing stiffness and damping. The bearing is modeled as spring. The result of this analysis is compared to that of other model having mean mesh stiffness. The effect of the excitation force by the unbalance off rotor off motor is also analyzed. Finally, the change ova natural frequency of the whole system due to the change of an angle between three shafts is compared in each case, and from this analysis, the avoiding angle for design is advised.

• Journal of Mechanical Science and Technology
• /
• 제20권12호
• /
• pp.2105-2114
• /
• 2006

In this paper, a simplified model is studied to predict analytically the vibration from the helical gear system due to an axial excitation of helical gears. The simplified model describes gear, shaft, bearing, and housing. In order to obtain the axial force of helical gears, the mesh stiffness is calculated in the load deflection relation. The axial force is obtained from the solution of the equation of motion, using the mesh stiffness. It is used as a longitudinal excitation of the shaft, which in turn drives the gear housing through the bearing. In this study, the shaft is modeled as a rod, while the bearing is modeled as a parallel spring and damper only supporting longitudinal forces. The gear housing is modeled as a clamped circular plate with viscous damping. For the modeling of this system, transfer matrices for the rod and bearing are used, using a spectral method with four pole parameters. The model is validated by finite element analysis. Using the model, parameter studies are carried out. As a result, the linearized dynamic shaft force due to the gear excitation in the frequency domain was proposed. Out-of-plan displacement from the forced vibrating circular plate and the renewed mode normalization constant of the circular plate were also proposed. In order to control the axial vibration of the helical gear system, the plate was more important than the shaft and the bearing. Finally, the effect of the dominant design parameters for the gear system can be investigated by this model.

• 한국생산제조학회지
• /
• 제6권2호
• /
• pp.67-75
• /
• 1997

The noise . vibration characteristics of Hypoid gears which were made from three seperate materials(SCM, TSCM, SNCM) under the identical process were investigated for the sake of durability improvement of differential gear compatible with low level noise gear set. For this study, we developed a rig experimental equipment which can perform close noise.vibration experiment of differential gear. Consequently, we could analyze the noise.vibration characteristics of final reduction gear by materials, and also we observed changes in both metallic structure and hardness according to the materials of pinion gear. In addition to this, the correlation between the vibration of the differential gear and the interior noise of the passenger vehicles was proved by analyzing the results of rig vibration experiment and field noise test.

• 한국소음진동공학회논문집
• /
• 제23권4호
• /
• pp.301-307
• /
• 2013

MRU(motor reduction unit) for KTX is a assembled complex structure that is equipped with a lot of parts at the express train KTX and that is the core power source operating variable speeds. This study is recorded the dynamic characteristics analysis results tested by EMA which is done through the parts and assembly test, transient analysis and stoped train test in order to design the online monitoring system for KTX MRU. And the mode shapes result from critical vibration frequency explain the relation with variable speeds of express train over 250 km/hr. Also these variable speeds make variable operational frequencies at pinion, axle gear mesh frequency and normal bearing fault frequencies. As the specified speed can make resonance with natural frequencies of the MRU, for the train operating stability, this study also presents the MRU's critical speeds calculated by the each train speed.

• 한국소음진동공학회논문집
• /
• 제25권6호
• /
• pp.391-398
• /
• 2015

The swing noise of an excavator is reduced in this study. When an excavator is under a swing motion, it produces the annoying noise which is required to be reduced. To identify the characteristics of the swing noise, the signals of noise and vibration from an excavator are measured during the swing motion. From the variation of the driving motor speed, the noise and vibration signals are picked up and plotted in the waterfall plots. From the waterfall plots, we identify the frequency components corresponding to the driving motor frequency, the gear mesh frequency of the planetary gear, and their harmonics. In addition, the natural frequencies and modes of the center frame are extracted by using the experimental modal test. It is found that the swing noise is amplified when the gear mesh frequencies coincide with the natural frequencies of the center frame. To reduce the swing noise, the structural modification is performed to the center frame. Finally, it is observed that the noise is considerably reduced by the structural modification.

• 한국해양공학회지
• /
• 제37권4호
• /
• pp.164-171
• /
• 2023

Vibration and noise must be considered to maximize the efficiency of a yaw system and reduce the fatigue load acting on a wind turbine. This study investigated a method for analyzing yaw-system vibration based on the change in the load-duration distribution (LDD). A substructure synthesis method was combined with a planetary gear train rotational vibration model and finite element models of the housing and carriers. For the vibration excitation sources, the mass imbalance, gear mesh frequency, and bearing defect frequency were considered, and a critical speed analysis was performed. The analysis results showed that the critical speed did not occur within the operating speed range, but a defect occurred in the bearing of the first-stage planetary gear system. It was found that the bearing stiffness and first natural frequency increased with the LDD load. In addition, no vibration occurred in the operating speed range under any of the LDD loads. Because the rolling bearing stiffness changed with the LDD, it was necessary to consider the LDD when analyzing the wind turbine vibration.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1347-1354
• /
• 1994

This paper deals with the experimental research, including measurement and analysis and field survey, on the causes of occurring noise defective gear boxes in hoist production plant in order to reduce the fraction of their occurrence. In this reserch following investigations are performed : measurement and gear-boxes, examination of each machining process of production, measurement and analysis of dimensional accuracy of each part, comparative vibration test with exchanging inaccurate parts. From these investigations, it is found that the machining accuracy of pinion gear tooth thickness is the most sensitive factor of noise problem. By maintaining the tooth thickness error within 0.05 mm tolerance in the gear cutting process, the fraction of noise defective gear-boxes are greatly reduced to less than 2%, where the usual rate of it has been 20-50%.

• 한국소음진동공학회논문집
• /
• 제21권1호
• /
• pp.41-46
• /
• 2011

In this paper, we experimentally investigate factors that decrease in noise of a industrial take-out robot at driving state. For this, we analyse change in the noise of the take-out robot with gear machining accuracy and clearance. In order to calculate the noise related to gear machining accuracy that is based upon the Japanese Industrial Standard(JIS), we equally increase motor speed from 0 rpm to 1250 rpm. In addition, to investigate influence of clearance on noise, we evenly change clearance from 0.5 mm to 1.2 mm. These experiments show that clearance is more effective factor than gear machining accuracy to reduce the noise of the take-out robot.

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.111-117
• /
• 2005

The vibration problems associated with gear coupled rotors have been the focus of much engineering work. These systems are complex and difficult to analyze in that they have the problems associated with conventional rotors plus those additional problems associated with the gear couplings. This paper examines the problems peculiar to the gear mesh. Because of the meshing action of gears, the elasticity of the gear teeth introduces time-varying stiffness coefficients into the governing equations of motion. This means that system response must be thought of in terms of Mathieu-type equations, where multiple-frequency response occur due to the periodic coefficients. The meshing action of the gears also couples the lateral and torsional gear motions. Gear errors, such as tooth profile and spacing errors, produce forces and torque that excite the system at multiple frequencies, some of which are much higher than shaft rotational speed. To investigate how to the time-varying stiffness in the gear teeth and the gear errors act one the dynamic response of the gear coupled rotors, a three-dimensional dynamic model with lateral-tortional oscillation is developed. The harmonic balance technique is employed to solve this mathieu-type problem.