• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.1
• /
• pp.36-45
• /
• 2010

This paper shows a multiplexing technique to maximize the application of a moire-fringe based fiber optic sensor to lots of structure. Especially, a novel fringe-based fiber optic sensor was proposed to overcome the difficulty of multiplexing of a previous moire-fringe-based fiber optic sensor. The novel fringe-based fiber optic sensor is composed of a single reflective fringe and two optical fibers. Therefore, the multiplexing is easily realized because of the simplicity of optic structure inside the sensor. This paper also proposed four models of the multiplexing techniques. The models are based on a wavelength division multiplexing(WDM) technique and a time division multiplexing(TDM) one. Basically, the models would be profitable for a general extrinsic fiber optic sensor such as the fringe-based fiber optic sensor. Finally, the real optic system was manufactured by using the proposed model and successfully examined to prove the feasibility of the model for the application.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.3
• /
• pp.200-206
• /
• 1999

This paper describes the stress analysis of a curved beam by using photoelasticity. In order to measure accurate isochromatic fringe orders at certain locations. fringes are doubled and sharpened by digital image processing. After fringe multiplication and sharpening. fringe orders can be read as a quarter order interval (N=0, 1/4, 2/4, 3/4,...). The results obtained from photoelastic experiment are compared with those calculated by using theory. Two results are agreed well even though there are some scatter bands with maximum 8 percent for the results of photoelastic measurements and theoretical calculation. Difference may be occurred due to the slight misalignment of the direction to which axial load is applied in photoelastic experiment. It is confirmed that accurate measurement of stress distribution can be possible by using the techniques of fringe multiplication and sharpening in photoelasticity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.305-310
• /
• 2004

We have studied the optimal phase retardation value of a homogeneously aligned liquid crystal (LC) driven by fringe-field when using the LC with positive dielectric anisotropy. In general, the transmittance of a homogeneous aligned LC cell under crossed polarizer is maximum when a twist angle of LC by in-plane rotation is 45$^{\circ}$ with polarizer and the cell retardation becomes λ/2. However, the device using the LC with positive dielectric anisotropy does not follow this since the degree of rotation of the LC is dependent on electrode position and in addition the LCs tilt up along the fringe-field. At the center of common and pixel electrode, the LC is most twisted around a middle position of a cell whereas at the edge position of pixel electrode, the LC is most twisted near bottom surface of a cell. Consequently, the optimal phase retardation of the device becomes much larger than λ/2 and the transmittance can be described using the combination of the in-plane switching and twisted nematic mode.

• Current Optics and Photonics
• /
• v.1 no.6
• /
• pp.587-597
• /
• 2017

The extraction of the valid measurement region from the interference fringe pattern is a significant step when measuring gear tooth flank form deviation with grazing incidence interferometry, which will affect the measurement accuracy. In order to overcome the drawback of the conventionally used method in which the object image pattern must be captured, an improved segmentation approach is proposed in this paper. The interference fringe patterns feature, which is smoothed by the nonlinear diffusion, would be extracted by the structure tensor first. And then they are incorporated into the vector-valued Chan-Vese model to extract the valid measurement region. This method is verified in a variety of interference fringe patterns, and the segmentation results show its feasibility and accuracy.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.9 s.180
• /
• pp.2313-2318
• /
• 2000

The method of photoelasticity allows one to obtain principal stress differences and principal stress directions in a photoelastic model. In the classical approach, the photoelastic parameters are measured manually point by point. This is time consuming and requires skill in the identification and measurement of photoelastic data. Fringe phase shifting method has been recently developed and widely used to measure and analyze fringe data in photo-mechanics. This paper presents the test results of photoelastic fringe phase shifting method for the stress analysis of a curved beam plate. The technique used here requires four phase stepped photoelastic images obtained from a circular polariscope by rotating the analyzer at 0˚, 45˚, 90˚ and 135˚. Experimental results are compared with those of ANSYS and calculated by the simple beam theory. Good agreement among the results can be observed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.2
• /
• pp.201-206
• /
• 2004

We have performed computer simulation and experiment to obtain electro-optic characteristics of reflective hybrid aligned nematic (R-HAN) cell driven by fringe field, in which the cell consists of polarizer, optical compensation film, LC layer and reflector. Conventional R-HAN cell driven by fringe field using only the LC layer shows high wavelength dispersion at dark-state and thus viewing angle characteristic is strongly wavelength-dependent. In order to improve this demerit, we added one optical compensation film to conventional R-HAN cell. The display with optimized cell parameters shows low wavelength dispersion at dark-state and exhibits a wide viewing angle without the occurrence of grey scale inversion over a wide range of viewing angles and the contrast ratio greater than 5 over exists about 120$^{\circ}$ in vortical direction and 160$^{\circ}$in horizontal direction. Experimental results show good agreements with theoretical results and fast response time.

• Journal of the Optical Society of Korea
• /
• v.17 no.5
• /
• pp.415-422
• /
• 2013

White-light phase-shifting interferometry (WLPSI) is widely recognized as a standard method to measure shapes with high resolution over a long distance. In practical applications, WLPSI, however, is associated with some degree of ambiguity of its phase, which occurs due to a phase delay, which is the offset between the phase of the fringes and the fringe envelope peak position. In this paper, a new algorithm is proposed for the determination of a fringe order suitable for samples in which the phase delay mainly occurs due to noise, diffraction and a steep angle. The concepts of the decouple factor and the connectivity are introduced and a method for calculating the decouple factor and the connectivity is developed. With the phase-unwrapping procedure which considers these values, it is demonstrated that our algorithm determines the correct fringe order. To verify the performance of the algorithm, a simulation was performed with the virtual step height under noise. Some specimens such as step height standard and a column spacer with a steep angle are also measured with a Mirau interference microscope, after which the algorithm is shown to be effective and robust.

• Journal of the Korean Mathematical Society
• /
• v.53 no.4
• /
• pp.847-868
• /
• 2016

Let M be an invariant subspace of $H^2$ over the bidisk. Associated with M, we have the fringe operator $F^M_z$ on $M{\ominus}{\omega}M$. It is studied the Fredholmness of $F^M_z$ for (generalized) zero based invariant subspaces M. Also ker $F^M_z$ and ker $(F^M_z)^*$ are described.

• Journal of the Optical Society of Korea
• /
• v.14 no.4
• /
• pp.357-362
• /
• 2010

The joint transform correlator (JTC) has been the best known technique for pattern recognition and identification. This paper proposes a new technique of fringe adjustment by adopting a sinusoidal amplitude-modulated iterative filter convolved with an interference fringe pattern in the joint power spectrum (JPS) domain. The comparison of our new technique and other techniques is presented to show that the newly proposed technique can successfully improve both the correlation peaks and the peak signal-to-noise ratio (PSNR). Simulated results of enhanced interference fringes are also presented.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1982-1989
• /
• 2004

In photoelasticity, the directions of principal stresses are given by isoclinic fringe patterns. In this study, photoelastic theory is represented by Jones calculus and the photoelastic 8-step phase shifting method is described. A feasibility study using computer simulation is done to get isoclinics from photoelastic fringes of a circular disk under diametral compression. Fringe patterns of the disk are generated from the stress-optic law. The magnitudes of isoclinics obtained from the fringe patterns of computer simulation and experiment are compared with those of theory. The results are close between them. Then, the 8-step phase shifting method is applied to get distributions of isoclinics along the specified lines of a cuved beam plate under tensile load. Experimental results obtained from the phase shifting method were compared with those of finite element analysis (ANSYS). It is confirmed that measurement of isoclinic distributions is possible by use of photoelasitc phase shifting method.