• 한국소음진동공학회논문집
• /
• 제24권1호
• /
• pp.28-34
• /
• 2014

This study provides the numerical finite-element method(FEM) estimating the friction noise induced by the negative slope in the friction-velocity curve. The friction noise due to the friction-velocity curve is experimentally investigated through the pin-on-disk setup. The measured squeal frequency is estimated by FEM. The friction curve is measured by the friction test, then it is applied to the complex eigenvalue analysis. The results shows that the experimental squeal frequency can be determined by the FEM analysis. Also, it is emphasized that the negative friction-velocity slope is essential in generating friction noise in the pin-on-disc system.

• 한국소음진동공학회논문집
• /
• 제23권5호
• /
• pp.423-430
• /
• 2013

The characteristics of friction noise due to the friction-velocity curve is experimentally investigated through the pin-on-disk setup. The rotation speed of the disk is controlled in order to produce the sliding speed variation. Then, the friction coefficient and the corresponding friction noise are simultaneously measured with respect to the sliding speed between the steel disk and aluminum pin. The experimental results show that the negative friction-velocity slope is essential in generating friction noise.

• 한국소음진동공학회논문집
• /
• 제22권2호
• /
• pp.163-169
• /
• 2012

The brake squeal propensity associated with friction curve is investigated by using the hybrid finite element(FE)-analytical model. The modal analysis of an actual disc and pad is conducted by FE method. Also, the modeling for the accurate contact and disc rotation is analytically achieved. The eigenvalue analysis for the hybrid model provided the squeal dependency on the friction curve. Particularly, some pad modes and the disc torsion mode are shown to be sensitive for the friction curve.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권1호
• /
• pp.195-211
• /
• 2015

Flat plate friction lines have been used in the process to estimate speed performance of full-scale ships in model tests. The results of the previous studies showed considerable differences in determining form factors depending on changes in plate friction lines and Reynolds numbers. These differences had a great influence on estimation of speed performance of full-scale ships. This study was conducted in two parts. In the first part, the scale effect of the form factor depending on change in the Reynolds number was studied based on CFD, in connection with three kinds of friction resistance curves: the ITTC-1957, the curve proposed by Grigson (1993; 1996), and the curve developed by Katsui et al. (2005). In the second part, change in the form factor by three kinds of friction resistance curves was investtigated based on model tests, and then the brake power and the revolution that were finally determined by expansion processes of full-scale ships. When three kinds of friction resistance curves were applied to each kind of ships, these were investigated: differences between resistance and self-propulsion components induced in the expansion processes of full-scale ships, correlation of effects between these components, and tendency of each kind of ships. Finally, what friction resistance curve was well consistent with results of test operation was examined per each kind of ships.

• 한국전산유체공학회지
• /
• 제11권1호
• /
• pp.43-51
• /
• 2006

A fluid transient analysis on the Koreasat 1 & 2 pipeline system is conducted through numerical parametric studies in which unsteady friction results are compared with quasi-steady friction results and show relatively accurate prediction of the response curve with the unsteady friction. The code developed and used in this analysis has finished verification through comparing with the original Zielke model, the full and recursive convolution model and quasi-steady model as a reference. The unsteady friction is calculated by the recursive convolution Zielke model in which a complete evolution history of velocity field is no longer required so that it makes the fluid transient analysis on the complicated system possible. The results show that the application of quasi-steady friction to model cannot predict the entire response curve properly except the first peak amplitude but the application of unsteady friction to model can predict reasonably the response curve, therefore it is to know the characteristics of the propulsion system.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2006년도 PARALLEL CFD 2006
• /
• pp.320-323
• /
• 2006

A fluid transient analysis on the Koreasat 1 & 2 pipeline system is conducted through numerical parametric studies in which unsteady friction results are compared with quasi-steady friction results and show relatively accurate prediction of the response curve with the unsteady friction. The code developed and used in this analysis has finished verification through comparing with the original Zielke model, the full and recursive convolution model and quasi-steady model as a reference. The unsteady friction is calculated by the recursive convolution Zielke model in which a complete evolution history of velocity field is no longer required so that it makes the fluid transient analysis on the complicated system possible. The results show that the application of quasi-steady friction to model cannot predict the entire response curve properly except the first peak amplitude but application of unsteady friction to model can predict reasonably he response curve, therefore it is to know the characteristics of the propulsion system.

• International Journal of Automotive Technology
• /
• 제3권4호
• /
• pp.171-176
• /
• 2002

A bench test set-up is employed to simulate the friction characteristics of a paper-based friction material operating against a steel plate. Dry friction tests are run as well as tests with transmission fluids. Glazed friction material produces a negative coefficient of friction versus sliding velocity (f-v) curve for both dry friction and lubrication with transmission fluids. At low sliding speeds, the coefficient of friction when operating in transmission fluids for glazed friction materials is greater than that under dry friction. An appreciable negative f-v slope occurs at low sliding speeds for glazed friction materials when running with the transmission fluid. The friction material after running in produces a constant f-v curve under dry friction and a negative slope when lubricated with transmission fluid. At low sliding speeds, the coefficient of friction of the run-in friction material is lower than that of the glazed wet material. On the other hand, the run-in friction material has a larger friction coefficient than does the glazed friction material at higher sliding speeds.

• 한국소음진동공학회논문집
• /
• 제22권12호
• /
• pp.1206-1212
• /
• 2012

The brake squeal propensity due to the friction-velocity curve is numerically investigated. The finite element models for the disc and pad are correlated with the modal test. In the friction-engaged system modeling, the friction function is linearized at the equilibrium. The damping term induced by friction-velocity slope is incorporated into the equations of motion. In the complex eigenvalue analysis, it is found that the pad shear mode is very sensitive to the friction curve. The results shows that the squeal propensity of the pad shear mode can be controlled by the design parameters such as pressure and stiffness.

• 대한기계학회논문집A
• /
• 제40권5호
• /
• pp.449-455
• /
• 2016

본 연구는 마찰 특성이 다른 재질 별로 마찰에 의한 소음을 해석하는 스퀼 유한요소 해석 방법론을 제안하고 이를 실험 검증하고자 하였다. 회전운동 실험 장치를 통하여 각 재질 별 마찰곡선을 확인하였으며, 왕복운동 시험 장치에서 재질 별 마찰 소음을 계측하였다. 계측 된 마찰곡선을 특정 속도에서 선형화하여 마찰곡선 기울기 데이터를 FE Model에 적용하였다. 제안 된 해석 모델에서 발현 된 불안정 모드가 시험에서 발생한 스퀼 주파수와 유사함을 보였다.

• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.188-193
• /
• 2005

Surface texturing of tribological application is another attractive technology of friction reducing. Also, reduction of friction is therefore considered to be a necessary requirement for improved efficiency of machine. In this paper attempts to investigate the effect of density for micro-scale dimple pattern on bearing steel flat mated with pin-on-disk. We demonstrated the lubrication mechanism for a Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. It is found that friction coefficient is depended on the density of surface pattern. It was thus verified that micro-scale dimple could affect the friction reduction considerably under mixed and hydrodynamic lubrication conditions from based on friction map. Lubrication condition regime has an influence on the friction coefficient induced the density of micro dimple.