• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.627-635
• /
• 1997

In general, the booming noise intensity at tunnel exit is strongly related to the gradient of the compression wave front created by high speed train entering the tunnel. This paper presents some results in relation with the compression wave front produced when the high speed train enters a tunnel. Four kinds of tunnel entrance shape with real dimensions were studied to investigate the formation of compression wave front inside tunnel by train entering tunnel. Computations were carried out using three-dimensional compressible Euler equation with vanishing viscosity and conductivity of fluid. According to the reslts, the flow disturbance occured at tunnel entrance were eliminated by tunnel hood with same cross sectional area. The compression wave front is formed completely at 30-40m from tunnel entrance. The maximum pressure gradient of compression wave front is reduced by 29.8% for the inclined tunnel hood and reduced by 21.5% for the tunnel hood with holes at the top face with tunnel without hood. The length of the inclined hood is 15m and the length of the hood with holes is 20m.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.2
• /
• pp.142-149
• /
• 2004

Recently, the government introduced the thermal storage system for reducing the electric power load. Especially, the ice slurry type has gained lots of interest due to its good heat transfer and flowing characteristics. This study was peformed to understand the effects of transporting ice slurry through elbows of various angle. Propylene glycol water solution was used and about 2 mm ice particles were circulated. The experiments were carried out under various conditions, such as concentration and velocity of water solution ranging between 0∼20 wt％, 1.5∼2.5 m/s, respectively. And elbows with 4 different angles of 30$^{\circ}$, 45$^{\circ}$, 90$^{\circ}$, 180$^{\circ}$. The differential pressure and IPF (ice packing factor) between the pipe entry and exit were measured. The tendency of pressure loss and outlet IPF in elbow is that the pressure loss was reduced as concentration and flow velocity of water solution is increased, and low value appeared at 10 wt％ and 2.5 m/s. The variation of outlet IPF was compared with the inlet IPF in the range of $\pm$20％.

• Journal of Navigation and Port Research
• /
• v.34 no.1
• /
• pp.71-75
• /
• 2010

This study is experimented to observe an influence of experimental conditions on production characteristics of slurry ice by injection operating water to cooling plate. And at this experiment it used ethylene glycol-water solution and the concentration is 10 to 20wt%. The experimental apparatus was constructed of ethylene glycol-water solution and slurry ice storage tank, brine tank, pumps for ethylene glycol-water solution and brine circulating, a mass flow-meter, data logger for fluid temperature measuring and a vertical circular tube with single copper plate as test section. The experiments were carried out under various conditions, with mean velocity of fluid at the entry ranging from 1.0 to 2.0m/s and the cooling temperature of $-17^{\circ}C$ to $-10^{\circ}C$.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2014.04a
• /
• pp.196-198
• /
• 2014

최근 차세대 네트워크 패러다임으로 주목받는 소프트웨어 정의 네트워킹 (SDN)에서는 네트워크를 컨트롤 플레인과 데이터 플레인으로 나누고 중앙집중형 제어를 통해 효과적이고 유연한 네트워크 관리를 가능하게 한다. 하지만 잦은 컨트롤 이벤트 발생으로 인한 컨트롤러 및 컨트롤 채널의 부하와 거대한 플로우 엔트리 크기로 인한 스위치 내 TCAM(Temary Content Addressable Memory) 메모리 부족문제 등의 본질적인 문제로 실제 네트워크 적용 시 확장성 문제가 야기된다. 이러한 문제를 해결하기 위해 기존의 연구들은 컨트롤러의 연산능력을 향상시키거나, 컨트롤 이벤트의 발생을 줄이는데 초점이 맞춰져 왔으며, 한정적인 TCAM 공간의 효율적인 사용에 대한 연구는 부족한 상황이다. 따라서 본 논문에서는 효율적인 TCAM 자원 활용을 위한 플로우테이블 관리 기법을 제안한다. 제안 기법은 플로우 엔트리의 클러스터링을 통해 플로우 엔트리를 특성에 따라 그룹화하고 사용빈도를 기준으로 분할 및 병합을 수행함으로써 스위치 내의 가용한 플로우 수를 최대화한다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.3
• /
• pp.22-30
• /
• 2011

There is a many way of LPRE throttling methods, high-pressure-drop systems, dual-manifold injector, gas injection, multiple chambers, pulse modulation and movable injector components. Especially dual-manifold injector is essentially combines two fixed-area injectors into a common structure, with independent feed systems controlling flow to each injector manifold. In this paper, using indirect photography and liquid film thickness measurement with various injection pressure and tangential entry diameter to decide stability of spray over a wide thrust range in dual manifold injector.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.18 no.3
• /
• pp.125-132
• /
• 2023

Roundabouts have strengths in traffic flow and safety but can present difficulties for inexperienced drivers. Demand to acquire and analyze drone images has increased to enhance a traffic environment allowing drivers to deal with roundabouts easily. In this paper, we propose a roundabout traffic analysis system that detects, tracks, and analyzes vehicles using a deep learning-based object detection model (YOLOv7) in drone images. About 3600 images for object detection model learning and testing were extracted and labeled from 1 hour of drone video. Through training diverse conditions and evaluating the performance of object detection models, we achieved an average precision (AP) of up to 97.2%. In addition, we utilized SORT (Simple Online and Realtime Tracking) and OC-SORT (Observation-Centric SORT), a real-time object tracking algorithm, which resulted in an average MOTA (Multiple Object Tracking Accuracy) of up to 89.2%. By implementing a method for measuring roundabout entry speed, we achieved an accuracy of 94.5%.

• Journal of the Korean GEO-environmental Society
• /
• v.6 no.4
• /
• pp.47-58
• /
• 2005

Development of underground space is conducted for various useful facility and underground structures and deep excavation technology for reclaimed area has been researched and developed. The seepage flow and behavior of phreatic line in reclaimed area was predominated by transient flow caused by tidal action. Also the soil-water characteristic relation is most important factor for transient flow analysis, therefore the research about the soil-water characteristic is strongly required. In this paper, laboratory tests (pressure cell, desiccator, and tensiometer test) and theoretical analysis were performed to investigate the soil-water characteristic such as air-entry value, metric suction, and residual water content. And the feasibility of prediction method for soil-water characteristic are presented by transient seepage analysis and comparison between analysis results and in-situ measured seepage flux in LNG TK-00 storage tank. Based on the result of laboratory and theoretical analysis, Fredlund and Xing's method provide to work out well for reclaimed ground soils. Also, the transient analysis result is more reasonable and effective for design of deep excavation work in coastal and reclaimed ground.

• Tunnel and Underground Space
• /
• v.31 no.5
• /
• pp.333-359
• /
• 2021

Gases such as hydrogen and radon can be generated around the canister in high-level radioactive waste disposal systems due to several reasons including the corrosion of metal materials. When the gas generation rate exceeds the gas diffusion rate in the low-permeability bentonite buffer, the gas phase will form and accumulate in the engineered barrier system. If the gas pressure exceeds the gas entry pressure, gas can migrate into the bentonite buffer, resulting in pathway dilation flow and advective flow. Because a sudden occurrence of dilation flow can cause radionuclide leakage out of the engineered barrier of the radioactive waste disposal system, it is necessary to understand the gas migration behavior in the bentonite buffer to quantitatively evaluate the long-term safety of the engineered barrier. Experimental research investigating the characteristics of gas migration in saturated bentonite and research developing numerical models capable of simulating such behaviors are being actively conducted worldwide. In this technical note, previous gas injection experiments and the numerical models proposed to verify such behaviors are introduced, and the future challenges necessary for the investigation of gas migration are summarized.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.10
• /
• pp.21-26
• /
• 2018

Soil-water characteristic curve, which is called soil retention curve, is required to explore water flows in unsaturated soils, relative permeability of water in multi-phase fluids flow, and change to stiffness and volume of soils. Thus, the understanding of soil-water characteristic curves of soils help us explore the behavior of soils inclduing fluids. Biopolymers are environmental-friendly materials, which can be completely degraded by microbes and have been believed not to affect the nature. Thus, various biopolymers such as deacetylated power, polyethylene oxide, xanthan gum, alginic acid sodium salt, and polyacrylic acid have been studies for the application to soil remediation, soil improvement, and enhanced oil recovery. PAA (polyacrylic acid) is one of biopolymers, which have shown a great effect in enhanced oil recovery as well as soil remediation because of the improvement of water-flood performance by mobility control. The study on soil-water characteristic curves of sandy soils containing PAA (polyacrylic acid) has been conducted through experimentations and theoretical models. The results show that both capillary entry pressure and residual water saturation dramatically increase according to the increased concentration of PAA (polyacrylic acid). Also, soil-water characteristic curves by theoretical models are quite well consistent with the results by experimental studies. Thus, soil-water characteristic curves of sandy soils containing biopolymers such as PAA (polyacrylic acid) can be estimated using fitting parameters for the theoretical model.

• Journal of Fisheries and Marine Sciences Education
• /
• v.29 no.1
• /
• pp.201-208
• /
• 2017

The major cause of the marine accidents is the collision with a moving object such as ship as well as the fixed object such as breakwater. Therefore, the most effective way to reduce the maritime ship accidents is the prevention of collision. In order to decrease the collision, it is principle that the navigation officer promptly judges the dangerous condition and makes the quick response. The ship does not allow any object or other ships approaching its surrounded area called ship area so that it prevents the collision. Generally, the ship which has high speed or poor maneuvering capability shall be managed from the distance so that the other ship does not invade its ship domains(watching distance, blocking distance). Accordingly, this study sets the navigational risk assessment model by applying ship dynamic domain and collision judgement method considered ship length, speed and navigational capability. It also reviewed the validity of the model and evaluated the perilous water way (Maenggol Channel) and a curved route near Maenggol Channel. As a result, in case of a ship with 100m in length passing Maenggol Channel, it represented "warning" level before 1.5nm to the entry, "dangerous"level 0.75nm before to it and "very dangerous" level 0.5nm before to it and then "dangerous"level again up to the entry. Applying to the curved route also showed the same results as the Narrow Channel or Maenggol Channel. This analysis highly matched with the actual navigation results. In the future, this model will be useful for coastal navigation safety chart development and safety evaluation for route or port development. It also allows to evaluate the dangerous route or the best route by applying the result into ECDIS so that it will finally help to reduce the marine accidents. Eventually the model will be effective for the marine traffic simulation evaluation forced by Maritime Traffic Safety Act.