• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.205-210
• /
• 2002

As the deposits of natural sands have slowly been depleted, it has resulted in an increase in manufactured fine aggregate (MFA). Standard specifications for fine aggregate for concrete contained in KS F 2558 permit a maximum of 7 percent finer than the No. 200 sieve (75${\mu}{\textrm}{m}$). Since the production process for MFA normally generates 10 to 20 percent of micro fines-which is defined as aggregates passing the No. 200 sieve (75${\mu}{\textrm}{m}$)-more than permitted by specifications, Excess fines must be removed by screening and/or washing operations. The amount of by-products will continue to grow as production increases with environmental discharge restrictions. This fundamental study focuses on experimental research for the adequacy of use of micro fines included in crushed aggregate using methylene blue test. Total of 63 types of sands from seven different rocks were tested. Based on the test results, the methylene blue test was turned out to be a good indicator of the quality of micro fines for concrete and a supplementary article and an amendment of the KS standard were recommended.

• 한국안전학회지
• /
• 제16권1호
• /
• pp.65-72
• /
• 2001

Portland cement concrete is made with coarse aggregate, fine aggregate, portland cement, water and, in some cases, selected chemical admixture such as air-entraining agents, water reducer, superplasticizer, and so on, and mineral admixture such as fly ash, silica fume, slags, etc. Typically, in the concrete, the coarse aggregate and fine aggregate will occupy approximately 80 percent of the total volume of the finished mixture. Therefore, the coarse and fine aggregates affect to the properties of the portland cement concrete. As the deposits of natural sands have slowly been depleted, it has become necessary and economical to produce crushed sand(manufactured fine aggregate). It is reported that crushed sand differs from natural sands in gradation, particle shape and texture, and that the content of micro fines in the crushed sand affect to the quality of the portland cement concrete. Therefore, the purpose of this paper is to investigate the characteristics of fresh and hardened concrete with higher micro fines. This study provides a firm data to apply crushed sand with higher micro fines.

• Geomechanics and Engineering
• /
• 제5권5호
• /
• pp.401-417
• /
• 2013

The results of an experimental program regarding the effects of gradation on shear strength and volume change behavior of silty sands are presented. Consolidated drained direct shear tests were performed on two clean base sands and twelve silty sands obtained by mixing those base sands with two different non-plastic silts at various fines contents (${\leq}$ 25%). Drained shear strengths were observed to be not significantly influenced by either base sand gradation or silt gradation or fines content for the studied range. Increasing fines content has increased the volumetric contraction of specimens at similar void ratio. However, the amount of increase in volumetric contraction of silty sands were found to be affected by silt gradation when other influencing factors such as fines content, base sand gradation and mineralogy were kept the same. Moreover, the amount of increase in volumetric contraction of silty sands were also found to be affected by base sand gradation when other influencing factors such as fines content, silt gradation and mineralogy were kept the same.

• 콘크리트학회지
• /
• 제7권3호
• /
• pp.149-155
• /
• 1995

무세골재 콘크리트에 석분을 혼입하므로써 얻을 수 있는 강도 증가효과를 조사하기 위하여 실험을 통한 연구를 수행하였다. 시멘트-골재의 비 1 : 6, 1 : 8 그리고 1 : 10 과 30~56% 사이의 여러 물 -시멘트 비를 배합설계시에 선정하였다. 작업하기 적당한 콘크리트를 얻기 위하여 필요에 따라 고유동화제를 시멘트중량의 1.5%사용하였으며, 석분을 혼입한무세골재 콘크리트의 경우 시멘트와 같은 중량의 석분을 혼입하였다. 여러 배합설계에 대한 압축강도와 인장강도 시험 결과를 비교분석하였다. 시험결과는 무세골재 콘크리트에 비하여 압축강도는 약 38%, 인장강도는 약 17%~72% 증가시킬 수 있음을 보여주고 있다.

• 펄프종이기술
• /
• 제33권1호
• /
• pp.16-23
• /
• 2001

Hydraulic transport of fines up to the surface of flotation cell was supposed to be a mechanism of fines fractionation through the froth-flotation. Efficient fractionation of fines means efficient skimming out of flotation rejects as much as possible with least long fiber loss. The selectivity of fines fractionation was found to be mainly affected by long fibers flocculation degree in this study. Lack of sufficient flocculation of long fibers could lead to extensive loss of long fibers. It was also found that higher flotation flux caused higher flotation reject as well as the increase of long fiber loss, but did not affect the fine content ratio in the flotation reject. We controlled the flotation flux and the stock consistency, and chose a cationic polymer to maximize the flocculation of long fibers and to increase the amount of flotation reject. The highest efficiency of fines fractionation was obtained at 1.3% of stock consistency and at 100L/min of flotation flux in our experimental set up. The cationaic polymer we chose was found to be very effective in fiber flocculation and flotation froth stabilization. New definitions of fractionation efficiency were introduced in this study to compare the results more clearly.

• 펄프종이기술
• /
• 제33권1호
• /
• pp.24-29
• /
• 2001

The base paper of corrugated board is mainly produced from Korean old corrugated container (KOCC), and thus the recycling rate of KOCC is very high. However, there is a problem that the pulp quality is very low while the recycling rate of OCC is high. The fines content in KOCC, the main source of the corrugated board, amounts to nearly the half of the total stock, and its formation increases as recycling process repeats due to the hornification of fiber. There have been attempts to improve the drainage property of OCC by increasing the headbox concentration of the paper machine or by applying drainage-promoting polymer additives. However, these conventional methods have problems of weakened paper strength and lowered converting fitness caused by paper formation hindrance. The strength of linerboard could not be increased in case KOCC is used, because hornified OCC pulp can-not be sufficiently refined due to the lowered drainage property caused by fines formation. We studied about a new technique consisting of froth-flotation for fractionating pulp stock into a long fiber portion and fines fraction. This study will be developed in order to enhance the drainage and strength properties of a recycled OCC pulp by selective treatment of flocculant on fractionated OCC Fines.

• 펄프종이기술
• /
• 제40권3호
• /
• pp.15-22
• /
• 2008

Properties of pulp fibers can be modified by LbL multilayering technology. We evaluated the effect of stock composition on the polyelectrolyte multilayering performance of pulp fibers in this study. Stock composition was varied with pulp type and fines content. Three types of pulp-Hw-BKP, BCTMP and KOCC-were treated with polyelectrolytes of poly-DADMAC and PSS. Fines content of stock were controlled at 0, 10, 20, 30, and 40%. Zeta potential of pulp fibers and charge demand of filtrate were evaluated. The highest adsorption ratio was obtained for BCTMP because of its shortest fiber length and highest specific surface area. Higher fines content in the stock increased the adsorption ratio of polyelectrolyte onto pulp fiber and it required a higher amount of polyelectrolyte for charge neutralization. For the pulp stock with higher fines content, a higher level of polyelectrolyte and the increased layer number were required to modify and stabilize the electrochemical properties of pulp fibers.

• 한국항해항만학회지
• /
• 제29권3호
• /
• pp.263-268
• /
• 2005

세립분의 함유량, 구속압력과 건조밀도에 따른 Sand Column의 투수성에 대한 시험을 실시하였다. 삼축투수시험은 세립분의 함유량 (5, 15, 25, $35{\%}$), 구속압력($\sigma_3^'=0.5,\;1.0,\;2.0,\;3.0{\cal}kg/{\cal}cm^2$)과 건조밀도($\gamma_d=1.50,\;1.55,\;1.60,\;1.65 {\cal}g/{\cal}cm^3$)를 달리한 여러 종류의 시료에 대하여 수행되었다. 삼축투수시험 결과 세립분 함유량, 구속압력 및 건조밀도가 커질수록 투수계수는 작아지는 것을 알 수 있었다. 특히, 세립분의 함유량에서는 $0.01{\cal}mm$ 입경 이하의 세립분이 증가할수록 투수성이 매우 크게 감소하고, 구속압력과 건조밀도에서는 낮은 구속압력수준 ($\sigma_3^'=0.5{\~}1.0{\cal}kg/{\cal}cm^2$)과 낮은 수준의 밀도($\gamma_d=1.50{\~}1.55{\cal}g/{\cal}cm^3$) 변화에서 투수성의 감소가 매우 크게 일어남을 알 수 있었다.

• 해양환경안전학회지
• /
• 제15권2호
• /
• pp.135-142
• /
• 2009

본 연구는 고성능콘크리트의 강도조절과 수화열 저감을 위하여 쇄석 쇄사 생산시 발생되는 쇄석미분말을 사용하여 고성능콘리트의 강도, 유동성 내구성능 및 건조수축 특성을 검토한 것이다. 실험결과 쇄석미분말은 치환율 10% 증가시마다 무치환시의 압축강도를 약 $10{\sim}15%$씩 감소시키며, 변형계수와 물구속비를 감소시켜 고성능콘크리트의 유동성 향상에 효과적이다. 또한, 고성능콘크리트에서 쇄식미분말 10% 치환시 마다 단위시멘트량 감소에 따른 최고 단열온도상승량을 약 $4^{\circ}C$씩 감소시켰다. 반면 건조수축랑은 10% 치환시마다 약 5% 증가시키는 것으로 나타났다. 한편 고성능콘크리트의 내구성은 단위분체량과 유동성향상에 따른 조직의 치밀화로 쇄석미분말의 치환에 관계없이 상대동탄성계수 100%이상으로 우수하게 나타났다. 이와 같이 문제로서 쇄석미분말의 사용은 치환량에 따른 고성능콘크리트의 강도조절이 가능하며 수차 발열량을 저감시킬 수 있다.

• 한국지반공학회논문집
• /
• 제28권9호
• /
• pp.97-106
• /
• 2012

본 논문에서는 혼합토의 역학적 특성을 해명하기 위한 기초연구로 모래와 비소성 실트로 구성된 혼합토를 대상으로 모래가 골격구조의 주체를 이루는 범위 안에서 다양한 세립분함유율로 조성된 공시체를 제작하였다. 모래입자의 파쇄가 발생하는 고압영역의 등방압축실험을 수행하기 위하여 고압삼축시험기를 이용하여 혼합토의 압축특성 및 파쇄에 대한 영향을 조사했다. 시험 결과, 모래의 압축특성은 입자파쇄가 발생함에 따라 항복에 도달한 뒤에는 1개의 NCL에 수렴하는 경향을 나타낸다. 한편, 혼합토의 압축특성은 세립분함유율이 증가함에 따라 조립자가 세립분에 의해 둘러싸여 쿠션작용에 의해, 조립자가 파쇄를 일으키기 어려워지므로 압축곡선의 최대경사가 완만해지고 항복응력 또한 증가함을 알 수 있다.