• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(2)
• /
• pp.76-79
• /
• 2000

The 3$\mu\textrm{m}$-thick PVDF (Polyvinyiidene fluoride) thin film have been prepared using physical vapor deposition with electric field, and its FT-IR specrum, dielectric property and electric conduction phenomenon have been investigated. Since the characteristic peaks ate detected at 509.45 and 1273.6〔cm〕 in the FT-IR spectrum, we are confirmed that the ${\beta}$ -phase is dominant in the PVDF thin film. In the results of dielectric properties, the PVDF thin film shows anomalous dispersion, i.e. gradual decrease of dielectric constant with increase of frequency, and also that the dielectric absorption point changes from 200Hz to 7000Hz with increasing temperature of thin film, which is consistent with the Debye's theory. The activation energy (ΔH) obtained from temperature dependence of dielectric loss is 21.64 ㎉/㏖. We confirm that the electric conduction mechanism of PVDF thin film is dominated by ionic conduction by investigating the dependence of the leakage current of the thin film on the temperature and the electric field.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.212-215
• /
• 2000

This paper presents the temperature effect of PET Film for insulation EHV Gas VT. We measured the Breakdown Voltage (BDV) and the Partial Discharge Initial Voltage(PDIV) for fresh and heated PET film. In this results, The BDV and PDIV of PET Film was affected by temperature variation and the number of PET Film. The PDIV and BDV of PET Film slightly increased for heating treatment increased as the temperature is increased. however, decreased over about $150^{\circ}C$.

• 한국수소및신에너지학회논문집
• /
• 제17권2호
• /
• pp.234-240
• /
• 2006

Al film(135.5 nm thick) with Pd film(39.6 nm thick) on the top of it was made by thermal evaporation method. Hydrogen absorption of Al/Pd film was measured by quartz crystal microbalance(QCM) method at room temperature. The sample was activated by hydrogen absorption and desorption cycling at room temperature. Hydrogen was introduced into the film by increasing hydrogen gas pressure step by step up to 640 torr at room temperature. Hydrogen concentration reached up to 25% at $5{\sim}10$ torr. But at high pressure the concentration decreased. This strange tendency was not understood yet. Further study is needed to find out the mechanism of hydrogen absorption in Al in Al/Pd film.

• 소성∙가공
• /
• 제21권1호
• /
• pp.30-35
• /
• 2012

FIM(Film Insert Molding) is an innovative method of producing decorated parts for a wide range of products. Because it requires fewer steps when compared to conventional production methods, the time and cost of manufacturing high quality components can be reduced considerably. In this paper, the effects of processing conditions on the warpage of film-insert molded plate were investigated by using a design of experiments. The dominant factors affecting warpage were mold temperature and holding pressure. Warpage increased with the temperature difference between stationary mold and fixed one. Even when the mold temperature difference was zero, the plate with a film was bent after ejection such that the film side protruded. As holding pressure increased, warpage decreased significantly. In addition warpage increased with time increment for the film-insert molded plates.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.99-100
• /
• 2002

Radial, tilting-pad proceeding bearings are applied in high speed rotating machines operating at stable small and mean loads and the peripheral speeds of proceeding reaching 150 m/s. The operation of bearing can be determined by static characteristics including the oil film pressure, temperature and viscosity distributions, minimum oil film thickness, load capacity, power loss, oil flow. The operation of 5-lobe tilted-pad proceeding bearing has been introduced at the assumption of adiabatic oil film. The oil film pressure, temperature and viscosity distributions habe received by iterative solution of the Reynolds', energy and viscosity equations. The resulting oil film force, minimum oil film thickness, power loss. oil flow, maximum oil film pressure, maximum temperature were computed for different sets of bearing geometric parameters as: bearing length to diameter ratio, pad angular length and width as well as pad relative clearance.

• 설비공학논문집
• /
• 제11권6호
• /
• pp.835-845
• /
• 1999

The objective of the present study was to investigate heat and mass transfer characteristics in a vertical falling film type absorber using LiBr-$H_2O$ solution with 6owt%. The experimental apparatus consisted of an absorber with inner diameter of 17.2 mm and length of 1150mm, a generator, an evaporator/condenser, a solution tank, a sampling trap etc. The parameters were solution temperature of 45 and $50^{\circ}C$, coolant temperature of 30 and $35^{\circ}C$, and film Reynolds numbers from 50 to 150. Pressure drop in the absorber increased as solution and coolant temperatures decreased. Pressure drop in the absorber increased up to the film Reynolds number of 90, and then decreased at the further increase of the Reynolds number above 90. The maximum absorption mass flux observed at the film Reynolds number of 90. Absorption mass flukes increased as coolant temperature decreased. Absorption mass fluxes and heat transfer coefficients under subcooled condition were larger than those under superheated condition. Heat transfer coefficients were affected by solution temperature more than coolant temperature. The maximum absorption effectiveness under the subcooled condition was 23% for coolant temperature of $30^{\circ}C$ and 31% for coolant temperature of $35^{\circ}C$ under the present experimental conditions.

• 센서학회지
• /
• 제31권3호
• /
• pp.163-167
• /
• 2022

In this study, we investigated a carbon nanotube (CNT) film sensor to detect hazardous and noxious substances distributed in seawater. The response change of the sensor was studied according to environmental temperature, and its temperature coefficient of resistance (TCR, α) was measured. The temperature of the CNT film (~50 ㎛) was in the range of 20-50 ℃, and αCNT was calculated to be -0.0011 %/ ℃. We experimentally confirmed that the CNT film had a smaller TCR value than that of the conventional sensor. Therefore, we investigated the response change of the CNT sensor according to temperature. The CNT sensor showed a relatively small error of approximately 2.3 % up to 30 ℃, which is within the temperature range of the seawater of the Korean Peninsula. However, when the temperature exceeded 40 ℃, the error in the CNT sensor increased by more than 5.2 %. We fabricated a metal oxide (ITO, indium-tin-oxide) film and compared its performance with that of the CNT sensor. The ITO sensor showed an error of >12.5 % at 30 ℃, indicating that in terms of the stability of the sensor to temperature, the CNT film sensor has superior performance.

• 대한기계학회논문집B
• /
• 제24권2호
• /
• pp.177-187
• /
• 2000

Measurements of temperature fields and film-cooling effectiveness have been conducted for a shower-head film cooling on the leading edge of a blunt body, which simulates a first-stage turbine stator. In this study, three injection cases are employed for an average blowing ratio based on freestream velocity, M, of 0.5, 1.0 and 1.5. Two (Case 1), four (Case 2) and six (Case 3) rows of normal holes are symmetrically drilled on the three tested circular-cylinder leading edges. The measurements show that regardless of M, the film-cooling effectiveness increases as the injection row is situated at farther downstream location. In Case 1, the film-cooling effectiveness is highest for M = 0.5 and lowest for M = 1.5. On the contrary, in Case 3, the film-cooling effectiveness is highest for M = 1.0 and lowest for M = 0.5. When M = 0.5, the film coverage by the first row of the injection holes deteriorates as the number of the injection row increases. In particular, the film-cooling effectiveness due to the injection through the first row of the holes in Case 3, has a nearly zero value.

• 한국정밀공학회지
• /
• 제25권8호
• /
• pp.88-95
• /
• 2008

Young's modulus of electroplated nickel thin film is systematically investigated using the resonance method of atomic force microscope. Thin layers of nickel to be measured are electroplated onto the surface of an AFM silicon cantilever and Young's modulus of plated nickel film is investigated as a function of process conditions such as the plating temperature and applied current density. It is found that Young's modulus of plated nickel thin film is as high as that of bulk nickel at low plating temperature or low current density, but decreases with increasing plating temperature or current density. The results imply that the plating rate increases as increasing the plating temperature or current density, therefore, slow plating rate produces a dense plating material due to the sufficient time fur nickel ions to form a dense coating.

• 한국전기전자재료학회논문지
• /
• 제18권4호
• /
• pp.297-302
• /
• 2005

Chemical mechanical polishing(CMP) performances can be optimized by several process parameters such as equipment and consumables (pad, backing film and slurry). Pad properties are important in determining removal rate and planarization ability of a CMP process. It is investigated the performance of oxide CMP process using commercial silica slurry after the pad conditioning temperature was varied. Conditioning process with the high temperature made the slurry be unrestricted to flow and be hold, which made the removal rate of oxide film increase. The pad became softer and flexible as the conditioning temperature increases. Then the softer pad provided the better surface planarity of oxide film without defect.