• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.54 no.6
• /
• pp.1036-1044
• /
• 2021

A linear array acoustic transducer with 12 tonpilz elements mounted independently on a gradual wedge-shaped tail mass was fabricated, tested and analyzed. The compensated transducer, which is modified by including a series inductance of 137 µH in the developed linear array transducer, attained improved figure of merit (FOM) performance characteristics compared with the uncompensated transducer. The four resonant frequency bands were identified from the measured FOM curve. The FOM response patterns over the frequency ranges of 31 to 40 kHz and 50 to 60 kHz were relatively uniform, whereas sharp resonance peaks were observed at around 73 kHz and 84 kHz. These results indicate that the developed linear array transducer can be used as an enhanced broadband transducer of echo sounder, and the operating frequency can be selected for more effective echo surveys in the fishing ground.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.729-731
• /
• 2013

The compensation characteristics of 40 Gbps optical signals depending on figure of merit (FOM) of dispersion compensating fiber with dispersion coefficient of -125 ps/nm/km are investigated in this research. Simulation results show that the more fiber span number and launch power increase, the more the effects of FOM of DCF on the compensated signals increase. However, it is also confirmed that the more the effects of optical nonlinearity increase, the more FOM decrease.

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.567-572
• /
• 2023

In this paper, the breakdown voltage of Pi-LDMOS (Partial isolation lateral double diffused metal oxide semiconductor) was analyzed by simulation. Breakdown voltage variation is investigated under various settings of Parial buied oxide(P-BOX) parameters(length, thickness, location) and their mechanism is specified. In addition, the change in on-resistance in the breakdown voltage and trade-off relationship was analyzed according to the change in the P-BOX parameter, and the Figure-of-merit(FOM) was calculated and compared. In proposed structure, Lbox=5 ㎛, tbox=2 ㎛, and Lbc=2 ㎛ showed the highest breakdown voltage of 138V, and Lbox=5 ㎛, tbox=1.6 ㎛, and Lbc=2 ㎛ showed the highest FOM. Compared to conventional LDMOS, the breakdown voltage is 123% and FOM is 3.89 times improved. Therefore, Pi-LDMOS has a high breakdown voltage and FOM, which can contribute to the improvement of the stable operating range of the Power IC.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.3
• /
• pp.284-291
• /
• 1997

A hydrogen liquefaction equipment by direct cooling has been designed and built at KIST. Cool-down characteristics and liquefaction performance of the equipment have been investigated. The hydrogen liquefaction equipment consists of a GM refrigerator, a liquefaction velssel, a radiation shield and a cryostat. It is found that the hydrogen starts to be liquefied in the liquefaction vessel after 40~50 minutes of cool-down from the gas state of 270K. The effect of natural convection phenomena of charged gas in liquefaction vessel on the cool-down characteristics is evaluated by comparing with those in vacuum of liquefaction vessel. It is seen that the cool-down time of a liquefaction vessel is substantially increased in vacuum environment of liquefaction vessel. The experiments have been performed for 1~5 atm of hydrogen pressure to investigate the influence of hydrogen pressure on the liquefaction rate and figure of merit(FOM). It is found that both liquefaction rate and FOM are increased as the charged hydrogen pressure is increased.

• Current Optics and Photonics
• /
• v.4 no.2
• /
• pp.134-140
• /
• 2020

A significant enhancement of the magneto-optical Faraday rotation and extraordinary optical transmission (EOT) in the cascaded double-fishnet (CDF) structure with periodic rectangular apertures is theoretically predicted by using the extended finite difference time domain (FDTD) method. The results demonstrate that the transmittance spectrum of the CDF structure has two EOT resonant peaks in a broad spectrum spanning visible to near-infrared wavebands, one of them coinciding with the enhanced Faraday rotation and large figure of merit (FOM) at the same wavelength. It is most important that the resonant position and intensity of the transmittance, Faraday rotation and FOM can be simply tailored by adjusting the incident wavelength, the thickness of the magnetic layer, and the offset between two metallic rectangular apertures, etc. Furthermore, the intrinsic physical mechanism of the resonance characteristics of the transmittance and Faraday rotation is thoroughly studied by investigating the electromagnetic field distributions at the location of resonance. It is shown that the transmittance resonance is mainly determined by different hybrid modes of surface plasmons (SPs) and plasmonic electromagnetically induced transparency (EIT) behavior, and the enhancement of Faraday rotation is mostly governed by the plasmonic electromagnetically induced absorption (EIA) behavior and the conversion of the transverse magnetic (TM) mode and transverse electric (TE) mode in the magnetic dielectric layer.

• Journal of the Korean Ceramic Society
• /
• v.54 no.6
• /
• pp.530-534
• /
• 2017

The figures of merit in the on-resonance and off-resonance conditions ($FOM_{on}$ and $FOM_{off}$) for the piezoelectric energy harvester (PEH) were measured and compared in $[(K_{0.485}Na_{0.515})_{1-X}Li_X](Nb_{0.99}Ta_{0.01})O_3$ (x = 0.04 ~ 0.09) (KNLNT) ceramics with various Li contents. The crystal structure of CuO-doped KNLNT ceramics changes from orthorhombic to tetragonal around the Li fraction of 0.065. The stable temperature range for the tetragonal phase widens to both higher and lower temperatures as Li is substituted. The piezoelectric charge constant ($d_{33}$), electromechanical coupling factor ($k_p$) and mechanical quality factor ($Q_m$) have maximum values at the Li fraction between 0.055 and 0.065 where the phase boundary lies between the orthorhombic and tetragonal phases. Both $FOM_{on}$ and $FOM_{off}$ have peak values around the phase boundary but the peak compositions are not exactly coincided. The optimal Li fraction in the KNLNT ceramic for a PEH application was found to be between 0.055 and 0.065.

• Journal of Power Electronics
• /
• v.19 no.6
• /
• pp.1440-1448
• /
• 2019

In wireless power transfer systems, it is important to design resonant energy links in order to increase the power transfer efficiency and to obtain desired system performances. This paper proposes a method for designing and analyzing the resonant energy links in a series-series configured IPT (inductive power transfer) system using the FOM-rd plane. The proposed FOM-rd graphical design plane can analyze and design the voltage gain and the power efficiency of the energy links while considering changes in the misalignment between the coils and the termination load condition. In addition, the region of the bifurcation phenomena, where voltage gain peaks are split over the frequency, can also be distinctly identified on the graphical plane. An example of the design and analysis of a 100 W inductive power transfer system with the proposed method is illustrated. The proposed method is verified by measuring the voltage gain and power efficiency of implemented hardware.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.2
• /
• pp.81-85
• /
• 2017

$SnO_2/Ag/Nb_2O_5/SiO_2/SnO_2$ multilayer films were prepared on glass substrate by sequential using RF/DC magnetron sputtering at room temperature. The influence of top $SnO_2$ layer thickness on optical and electrical properties of the multilayer films was investigated. Experimentally measured results exhibit transmittances over 84.3 ~ 85.8% at 550 nm wavelength. As the top $SnO_2$ layer thickness increased from 40 to 55 nm, the sheet resistance (Rs) increased from 5.81 to $6.94{\Omega}/sq$. The Haacke's figure of merit (FOM) calculated for the samples with various $SnO_2$ layer thicknesses was a maximum at 45 nm ($35.3{\times}10^{-3}{\Omega}^{-1}$).

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.464-466
• /
• 2003

In this paper an advanced algorithm for selecting a seam line automatically, which used to be selected by human operator for mosaicked images is presented. In addition to four factors proposed by automation theory, the FOM(Figure Of Merit) of tie point were taken into account to suggest the method to select a seam line applicatively and the algorithm was applied to mosaic test images.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.2
• /
• pp.131-139
• /
• 2000

A direct hydrogen liquefaction equipment has been developed and tested, which consists of a GM refrigerator, a liquefaction vessel, a radiation shield, a cryostat, and an ortho-para converter with catalyst. The effect of ortho-para hydrogen conversion on the performance of hydrogen liquefaction has been investigated. The time needed for the hydrogen liquefaction process with hydrogen pressure charge of 4 atm was delayed to around 75 minutes, and the liquefied mass flow rate of the hydrogen was about 0.0150∼ 0.0205 g/s when the hydrogen was liquefied with the direct hydrogen liquefaction system considering ortho-para conversion. With ortho-para conversion, the liquefied mass flow rate decreased up to 20%. Considering ortho-para conversion, there were up to 30% increase in the work input per unit liquefied mass flow rate. When the ortho-para conversion was considered, FOM decreased to be about 0.031∼0.045.