• Journal of Broadcast Engineering
• /
• v.14 no.2
• /
• pp.107-113
• /
• 2009

In Digital On-Channel Repeaters (DOCR) of Terrestrial-DMB (Digital Multimedia Broadcasting), there exist feedback signals generated from transmit antenna and re-entering at receive antenna. Therefore DOCR becomes unstable unless the feedback signal is properly eliminated. Previous research proposed a feedback canceller to estimate the feedback channel to deal with this problem. However formerly used estimation algorithms show unsatisfied performance in terms of convergence rate and quality although their implementations are simple. This paper applies PNLMS (Proportionate Normalized Least Mean Squares) adaptive algorithm to feedback channel estimation and evaluates the performances which solve the problem of feedback signal effectively.

• Journal of KSNVE
• /
• v.2 no.2
• /
• pp.107-116
• /
• 1992

An adaptive signal processing technique is implemented for the active noise cancellation of the plane acoustic wave propagating in a duct. To avoid the instability caused by the acoustic feedback from the control speaker to the detect microphone, an off-line modeling of the acoustic feedback plant is done using the FIR filter. Auxiliary path required for the filtered-x LMS algorithm is modeled as well. Before going into the experiments, a simulation is carried out under the same conditions with experiments. The simulation shows that the longer the length of the adaptive filter is, the better the results are achieved. Experiments have been carried out at lower audio frequency range (50 - 400Hz), and the results are in good agreements with those of simulation study. As a results of this adaptive noise control, around 50dB is reduced for a pure tone noise, and for a bandlimited noise with the bandwidth of 316Hz, a maximum of 30dB noise reduction is attained.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.69-72
• /
• 2002

In this paper, adaptive minimum mean-squared error (MMSE) multiuser detector combined with decision-feedback detector (DFD) is considered fur near-far resistant DS-CDMA system. To provide a reliable input to the adaptive MMSE detector, multiple-access interference (MAI) is regenerated using bit estimates from DFD and subtracted from the received signal. In the adaptive MMSE detector, the effect of the imperfect cancellation is compensated by a least mean square (LMS) algorithm. Through the numerical results, it is shown that, in a near-far situation, the proposed scheme provides superior performance to the matched filter (MF) receiver, adaptive MMSE detector, and DFD in terms of the bit error rate (BER).

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.183-184
• /
• 2007

As the mobile communication service is widely used, the demand for wireless repeaters is rapidly increasing because of the easiness of extending service areas. But wireless repeaters has a problem that the output of the transmit antenna is partially fed back to the receive antenna, which results in feedback interference. In this paper, we investigate the performance of adaptive variable step-size NLMS-based algorithms for cancelling the interference signals in the W-CDMA system under time-varying multipath channels. The criteria for comparison are tracking capability, convergence speed, and complexity.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.40-46
• /
• 2013

Automatic swing door for an automotive application is considered. The equation of motion for a driver side swing door is introduced and gravity cancellation control scheme is adapted. The control scheme supposed to cancel the moment due to the tilt of the car. A speed control is suggested for door operation automation but the output of the speed control is not suppose to be precise as for the manufacturing system control. In the frame of the velocity control of the door, feedback linearization was applied for collision detection. The collision detection performance is satisfactory. The estimate of the magnitude of disturbance due to the collision is close to the actual magnitude of disturbance. Simulation study has been performed to gain insight into the system behavior. Also real test on the prototype hardware has been performed for verification purpose.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.12
• /
• pp.2353-2362
• /
• 2015

In this paper, we employ the single channel full duplex radio for wireless local area network (WLAN) systems, and design digital interference cancellers using adaptive signal processing. When the full duplex scheme is used for WLAN systems with multiple transmit and receive antennas, some interference is caused through the feedback of transmit signals from multiple antennas. To remove the feedback interference, we derive the least mean square (LMS), normalized LMS (NLMS), and recursive least squares (RLS) algorithms based on adaptive signal processing techniques. In addition, we analyze the theoretical convergence of the proposed LMS and RLS methods. The channel capacity of full duplex radios increases by two times than that of half duplex radios, when the packet error rate (PER) performances for the two systems are identical. Through numerical simulations in WLAN systems, it is shown that the full duplex method with the proposed interference cancellers has a similar PER performance with the conventional half duplex transmission scheme.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.45-51
• /
• 2011

This paper presents a wideband low-noise amplifier (LNA) covering 800MHz~5.8GHz for various wireless communication standards by utilizing in a 0.13um CMOS technology. Particularly, the LNA consists of two stages to improve the low-noise characteristics, that is, a cascode input stage and an output buffer with noise cancellation technique. Also, a feedback resistor is exploited to help achieve wideband impedance matching and wide bandwidth. Measure results demonstrate the bandwidth of 811MHz~5.8GHz, the maximum gain of 11.7dB within the bandwidth, the noise figure of 2.58~5.11dB. The chip occupies the area of $0.7{\times}0.9mm^2$, including pads. DC measurements reveal the power consumption of 12mW from a single 1.2V supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.11C
• /
• pp.911-916
• /
• 2010

This paper proposes a new algorithm to cancel the acoustic feedback and noise signals in digital hearing aids. The proposed algorithm combines the feedback canceller to remove acoustic feedback signals and the noise canceller to reduce background noises. The feedback canceller is implemented by normal adaptive FIR filter, and the noise canceller is implemented by using the Wiener solution in frequency domain. This noise canceller has the transfer function presented by the power spectral density of signals. To verify the performances of the proposed algorithm, the simulations were carried out for the system. As the results of simulations, it was proved that we can advance 10.85dB output SNR on the average for the forward path gain of 0dB, and 11.04dB output SNR on the average for the forward path gain of 6dB, in the case of using the proposed algorithm.

• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.25-27
• /
• 2010

This paper presents a gain and phase mismatch calibration technique for an image-reject RF receiver. The gain mismatch is calibrated by directly measuring the output signal amplitudes of two signal paths. The phase mismatch is calibrated by measuring the output amplitude of the final IF output at the image band. The calibration of the gain and phase mismatch is performed at power-up, and the normal operation of the RF receiver does not interfere with the mismatch calibration circuit. To verify the proposed technique, a 2.4-GHz Weaver image-reject receiver with the gain and phase mismatch calibration circuit is implemented in a 0.18-${\mu}m$ CMOS technology. The overall receiver achieves a voltage gain of 45 dB and a noise figure of 4.8 dB. The image rejection ratio(IRR) is improved from 31 dB to 59.76 dB even with 1 dB and $5^{\circ}$ mismatch in gain and phase, respectively.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.11
• /
• pp.1447-1454
• /
• 2018

In this paper, the design of robust DSC-PLL(Delayed Signal Cancellation Phase Locked Loop) is proposed for coping with frequency variation. This method shows significant performance for detection of fundamental positive sequence component voltage when the grid voltage is polluted by grid unbalance and frequency variation. The feedback frequency estimation of DSC-PLL is tracking the drift in the phase by unbalance and frequency variation. The robust DSC PLL is to present the analysis on method and performance under frequency variations. These compensation algorithms can correct for discrepancies of changing the frequency within maximum 193[ms] and improve traditional DSC-PLL. Linear interpolation method is adopted to reduce the discretized errors in the digital implementation of the PLL. For verification of robust characteristic, PLL methods are implemented on FPGA with a discrete fixed point based. The proposed method is validated by both Matlab/Simulink and experimental results based on FPGA(XC7Z030).