• The Journal of the Acoustical Society of Korea
• /
• v.28 no.3
• /
• pp.229-238
• /
• 2009

This paper describes a sound engine of Korean traditional instruments, which are the Gayageum and Taepyeongso, by using a TMS320F2812. The Gayageum and Taepyeongso models based on commuted waveguide synthesis (CWS) are required to synthesize each sound. There is an instrument selection button to choose one of instruments in the proposed sound engine, and thus a corresponding sound is produced by the relative model at every certain time. Every synthesized sound sample is transmitted to a DAC (TLV5638) using SPI communication, and it is played through a speaker via an audio interface. The length of the delay line determines a fundamental frequency of a desired sound. In order to determine the length of the delay line, it is needed that the time for synthesizing a sound sample should be checked by using a GPIO. It takes $28.6{\mu}s$ for the Gayageum and $21{\mu}s$ for the Taepyeongso, respectively. It happens that each sound sample is synthesized and transferred to the DAC in an interrupt service routine (ISR) of the proposed sound engine. A timer of the TMS320F2812 has four events for generating interrupts. In this paper, the interrupt is happened by using the period matching event of it, and the ISR is called whenever the interrupt happens, $60{\mu}s$. Compared to original sounds with their spectra, the results are good enough to represent timbres of instruments except 'Mu, Hwang, Tae, Joong' of the Taepyeongso. Moreover, only one sound is produced when playing the Taepyeongso and it takes $21{\mu}s$ for the real-time playing. In the case of the Gayageum, players usually use their two fingers (thumb and middle finger or thumb and index finger), so it takes $57.2{\mu}s$ for the real-time playing.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.258-261
• /
• 2003

This paper is a studying of the vector control of AC servo motor using a high performance DSP(TMX320F2812). This DSP has many special peripheral circuits to drive a AC Servo motor as AD converter, QEP and so on. It makes us reduce the time of developing a control system and also can be simple size controller. We use vector control algorithm for instantaneous torque control and SVPWM algorithm by offset voltage methods.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.140-142
• /
• 2006

This paper represents a digital parallel control of a synchronous buck converter using a digital signal processor (DSP). The digital PWM and load sharing controller is implemented in the DSP TMS320F2812 and the experimental results are provided to show the feasibility of the digital synchronous buck regulator.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.3
• /
• pp.193-200
• /
• 2006

This paper suggests a 6-pulse-shift converter structure with PWM current-source inverter based on buck-boost configuration to improve the efficiency and to reduce the switching frequency of inverter for photovoltaic generation system, the device can be operated as interface system between solar module system and power system grid without energy storage cell. The circuit has six current-source buck-boost converter which operate chopper part and kas one full bridge inverter which make a decision the polarity of AC output. Therefore, the proposed PWM power inverter has advantages such as the reduction of witching loss and realization of unity power factor operation. The theoretical backgrounds are discussed and the input-output characteristics for the implemented prototype inverter using TMS320F2812 are verified experimentally in this paper.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.6
• /
• pp.29-34
• /
• 2007

It is important to analyse the frequency spectrum for the measurement of modulated signal, distortion, and noise. The frequency spectrum analysis is performed by the execution of Radix-2 DIT DFT i.e. FFT algorithm. The discrete input signal converted by A/D converter from the input signal in time domain is mathematically transformed to the frequency spectrum by FFT algorithm. In this study, we design the digital spectrum analyser by the hardware based on the TMS320F2812 DSP and AD9244 converter, and by the software based on the C28x S/W modules. We can timely analyse the frequency spectrum in mobile communication system by the digital frequency analyser based on the high performance DSP and S/W modules. This real-time analysing capability is the important performance in the internet-based mobile communication server system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.2
• /
• pp.110-118
• /
• 2008

The regulated peak power tracking (RPPT) systems such as the series structure and the parallel structure are commonly used in the satellite space power system. However, this structure processes the solar array power to the load through two regulators during one orbit cycle, which reduces the energy transfer efficiency. The series-parallel structure for the RPPT system can improve the power conversion efficiency, but an additional regulator increases the cost, size and weight of the system. In this paper, a simplified series-parallel space power system that consists of two regulators is proposed. The proposed system has the similar energy transfer efficiency with the series-parallel structure by adding one switch to the series structure, which reduces the cost, size and the weight. The large signal stability analyses is provided to understand the four main modes of system operation. In order to compare the energy efficiency with a series structure, the simulation is performed. The experimental verifications are performed using a prototype hardware with TMS320F2812 DSP and 200W solar arrays.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.827-830
• /
• 2011

In this paper, a wind speed & direction module and the DSP(Digital Signal Processor) sensor interface circuit board are proposed. This DSP system accepts and process the informations from a wind speed & direction module, the atmospheric pressure sensor, the ambient air temperature sensor and transfers it to the PC monitering system. Especially, a wind speed & direction module and a DSP hardware are directly designed and applied. A wind speed & direction module have a construction that it have four film type RTD(Resistive Temperature Detectors) or film type Piezo sensors adhered around the circular metal body for obtaining vector informations about wind. By this structure, the module is enabled precise measurement having a robustness about vibration, humidity, corrosion. A sensor signal processing circuit is using TMS320F2812 TI(Texas Instrument) Corporation high speed DSP.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.3
• /
• pp.66-74
• /
• 2005

This paper presents an implementation of digital servo speed control system of SPMSM(Surface-mounted Permanent Magnet Synchronous Motor) for industrial application with Direct Torque Control(DTC) using TMS320F2812 DSP. Although, the vector control scheme is adapted in many industrial servo system, but the DSP calculation ratio is increased by reference frame transformation and SVPWM of vector control. Therefore, this paper investigate the possibility of DTC scheme for industrial servo drive system instead of vector control scheme. DSP calculation ratio is compared between vector control and DTC algorithm in addition to the characteristic of speed control response. The suggested SPMSM control system shows the possibility of DTC scheme for industrial servo motor drive system instead of a vector control algorithm.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.897-900
• /
• 2007

This paper presents a study on the DSP controller and IGBT inverter driver design for the power-by-wire(PBW) system using BLDC servo motor. This BLDC servo motor system was realized with DSP(Digital Signal Processor) and IGBT inveter module. The PBW system needs speed control of servo motor for linear thrust action. This paper implements a servo controller with vector control and min-max PWM technique. As CPU of controller, TMS320F2812 DSP was adopted because it has PWM(Pulse Width Modulation) waveform generator, A/D(Analog to Digital) converter, SPI( Serial Peripheral Interface) port and many input/output port etc.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.3
• /
• pp.141-147
• /
• 2011

This paper proposes an efficient two-stage fault prediction algorithm for fault detection and diagnosis of induction motors. In the first phase, we use a linear predictive coding (LPC) method to extract fault patterns. In the second phase, we use a dynamic time warping (DTW) method to match fault patterns. Experiment results using eight vibration data, which were collected from an induction motor of normal fault states with sampling frequency of 8 kHz and sampling time of 2.2 second, showed that our proposed fault prediction algorithm provides about 45% better accuracy than a conventional fault diagnosis algorithm. In addition, we implemented and tested the proposed fault prediction algorithm on a testbed system including TI's TMS320F2812 DSP that we developed.