• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.416-421
• /
• 2000

The performance of gas turbine engines is affected by instabilities, like as rotating stall and/or surge. Rotating Stall is a transient intermediate stage between normal flow and complete flow breakdown leading to engine surge. Rotating Stall is associated with large amplitude nonaxisymmetric flow variations rotating around the compressor annulus. This paper presents the evolutions of stall propagation in a compressor cascade by numerical analysis. The flow phenomena due to stall cells and propagation speed are examined using 2 dimensional Navier - Stokes equations.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.5
• /
• pp.492-497
• /
• 2015

Currently, there are many kinds of tracked armored vehicles in service and they have encountered various environment and situations. So there are many obstacles to operate them improperly such as an engine stall. The causes of engine stall are an insufficient fueling, a mixture of air-fuel or vapor lock, and load increment which results from a rapid steering or increasing a viscosity of lubricant by low temperature. In this paper, engine stall by load increment due to a rapid steering or increasing of lubricant viscosity on tracked armored vehicles is analyzed, the ways to prevent it are applied, and their degrees of improvement are evaluated.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.16 no.3
• /
• pp.1-6
• /
• 2008

The stalling speed flight test of light airplane, ChangGong-91, was performed to acquire the certification. With power-off engine condition, the wings level stall flight tests were conducted at the aircraft configuration of various flap angle - clean, 20degree, and full flap, respectively. They were performed considering with the combination of the maximum and minimum test weight, and forward and afterward center of gravity. The stalling speeds and the minimum speeds of light airplane were determined from the results of flight test. Also, the appropriateness of stall warning speeds are evaluated through the flight test measures. The airplane is recoverable only with pitch control and engine throttle from stall state without exceptional operation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.1063-1066
• /
• 1996

On the prediction of driving performance, an acceleration performance is normally simulated in stall starting condition which is the engine status of full-throttle and high-speed. The lack of transient engine torque data makes the difficulty of predicting an acceleration performance on engine-idle start condition. A experimental equation of transient engine torque is derived from vehicle performance test data. It is applied to simulation the accleration performance prediction on idle starting condition.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.7
• /
• pp.105-111
• /
• 2006

The aircraft engine is to generate thrust for the maneuver of aircraft and to provide the power to the related hydraulic system and electrical system. Since the power provided to the systems is extracted from the high pressure compressor of aircraft engine, the extracted power is called horsepower extraction (HPX). If the HPX provided from the engine is smaller than the HPX required from the related systems, there could be abnormal engine behavior, like engine rollback or stall. Analysis on comparing the required HPX and the engine HPX capability had been performed during the T/A-50 FSD (Full Scale Development) period. The analysis results make the engine schedule changed, and T/A-50 flight test has been performed with the changed engine schedule. The analysis results and changing the engine control schedule were verified to be valid with the flight test results.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.6
• /
• pp.89-95
• /
• 2000

The engine idle speed mode becomes worse as one drives a vehicle for several years. This is due to ageing of engine and power-train parts. In this case, unstable idle conditions such as engine stall and droop are frequently experienced when the engine gets heavy torque loads due to power steering pump and air conditioning compressor. The objective of this paper is to study on the idle speed control using PID controller under load disturbances. The input of the PID controller is an error of rpm. The output of the PID controller is an ISCV duty cycle. The dSPACE Controller Boards are used to interface with engine. The on-vehicle test is realized using by SIMULINK and BLOCKSETS tools. The real time interface control panel supplied by Control Desk S/W is designed to have good results in engine idle speed control.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.161-167
• /
• 2001

This paper presents an approach to nonlinear engine idle controller and intake manifold absolute pressure(MAP) observer based on mean torque production model. A stable engine idle speed is important in that the unstable engine Idle mode can make engine to drooping or stall state. A sliding fuzzy controller has been designed to control engine idle speed under load disturbance. A sliding observer is also developed to estimate the intake manifold absolute pressure and compared with the actual MAP sensor value. The sliding mode observer has shown good robustness and good tracking performance. The inputs of sliding fuzzy controller are the errors of rpm and MAP. The output is a duty cycle(DC) for driving a idle speed control valve(ISCV).

• 한국전산유체공학회:학술대회논문집
• /
• 2002.10a
• /
• pp.121-126
• /
• 2002

Aircraft propulsion systems often use diffusing S-duct to convey air flow from the wing or fuselage intake to the engine compressor, Well designed S-duct should incur minimal total pressure losses and deliver nearly uniform flow with small transverse velocity components at the engine compressor entrance. Reduced total pressure recovery lowers propulsion efficiency and nonuniform flow conditions at the engine face lower engine stall limits. In this study, S-duct which has maximum total pressure recovery and nearly uniform flow profiles at the compressure intake should be found using design optimization methods with 3-dimensional Wavier-Stokes analyses.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.5
• /
• pp.134-140
• /
• 2015

A control program of an engine control module (ECM) was developed, and its control performance was verified on a 750Ps marine diesel engine. The control method was designed for an engine rotational speed control system. For ECM hardware, the commercial rapid control prototype (RCP) ECM was used. The programming tool for control algorithm development was the MatLab/Simulink. The main control algorithm assembled many control models as engine cranking, run, and stall. Each model has sub-models to input/output control signals. The target engine speed was input signal from a speed control lever, and control output signal of the ECM was sent to the unit-injectors for fuel injection. The engine test was performed under various conditions of engine rotational speeds and dynamometer loads. The test results show that the control function of the ECM is suitable for electrical marine diesel engines.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.879-885
• /
• 2000

This study is carried out to make clear the reason of occurrence of sudden acceleration incident of AT vehicle. The stepping motor is used to control the engine speed at idle by compensating the volume of air. By the way it's valve is contaminated by blow-by gas, deposit and back fire etc. This contamination could occur the load of motor at low temperature. This plays an important role in damaging the motor's coil with the motor's performance interfered. If it's coil is damaged the ISC could malfunction. If these phenomena occur, the speed of engine may increase or the engine may stall with hunting.