• Korean Journal of Materials Research
• /
• v.25 no.8
• /
• pp.386-390
• /
• 2015

Fe-base superalloy powders with $Y_2O_3$ dispersion were prepared by high energy ball milling, followed by spark plasma sintering for consolidation. High-purity elemental powders with different Fe powder sizes of 24 and 50 mm were used for the preparation of $Fe-20Cr-4.5Al-0.5Ti-O.5Y_2O_3$ powder mixtures (wt%). The milling process of the powders was carried out in a horizontal rotary ball mill using a stainless steel vial and balls. The milling times of 1 to 5 h by constant operation (350 rpm, ball-to-powder ratio of 30:1 in weight) or cycle operation (1300 rpm for 4 min and 900 rpm for 1 min, 15:1) were applied. Microstructural observation revealed that the crystalline size of Fe decreased with an increase in milling time by cyclic operation and was about 15 nm after 3 h, forming a FeCr alloy phase. The cyclic operation had an advantage over constant milling in that a smaller-agglomerated structure was obtained. The milled powders were sintered at $1100^{\circ}C$ for 30 min in vacuum. With an increase in milling time, the sintered specimen showed a more homogeneous microstructure. In addition, a homogenous distribution of Y-compound particles in the grain boundary was confirmed by EDX analysis.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.1
• /
• pp.6-10
• /
• 2018

Ni germanide (NiGe) is a promising alloy material with small contact resistance at the source/drain (S/D) of Ge MOSFETs. However, it is necessary to reduce the specific contact resistance between NiGe and the doped Ge S/D region in high-performance MOSFETs. In this study, a novel method is proposed to reduce the specific contact resistance between NiGe and p-type Ge (p-Ge) using a Tb interlayer. The specific contact resistance between NiGe and p-Ge was successfully decreased with the introduction of the Tb interlayer. To investigate the mechanism behind the reduction in the specific contact resistance, the elemental distribution and crystalline structure of NiGe were analyzed using secondary ion mass spectroscopy and X-ray diffraction. It is likely that the reduction in specific contact resistance was caused by an increase in the concentration of boron in the space between NiGe and p-Ge due to the influence of the Tb interlayer.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.4
• /
• pp.171-179
• /
• 2018

Copper powder dispersed with 4 vol.% of $Cr_2O_3$ was successfully produced by a simple milling at 210 K with a mixture of $Cu_2O$, Cu and Cr elemental powders, followed by Hot Pressing (HP) at 1123 K and 50 MPa for 2h to consolidate the milled powder. The microstructure of the HPed material was characterized by standard metallographic techniques such as XRD (X-ray Diffraction), TEM and STEM-EDS. The results of STEMEDS analysis showed that the HPed materials comprised a mixture of nanocrystalline Cu matrix and $Cr_2O_3$ dispersoid with a homogeneous bimodal size distribution. The mechanical properties of the HPed materials were characterized by micro Vickers hardness test at room temperature. The thermodynamic considerations on the heat of formation, the incubation time to ignite MSR (Mechanically induced Self-sustaining Reaction), and the adiabatic temperature for the heat of displacement reaction between the oxide-metal are made for the delayed formation of $Cr_2O_3$ dispersoid in terms of MSR suppression. The results of TEM observation and hardness test indicated that the relatively large dispersoids in the HPed materials are attributed to the significant coarsening for the high temperature consolidation; this leads to the low Vickers hardness value. Based on the thermodynamic calculation for the operating processes with a limited number of parameters, the formation kinetics and coarsening of the $Cr_2O_3$ dispersoid are discussed.

• Smart Structures and Systems
• /
• v.23 no.2
• /
• pp.107-122
• /
• 2019

As one of the most important parameters in structural health monitoring, structural frequency has many advantages, such as convenient to be measured, high precision, and insensitive to noise. In addition, frequency-change-ratio based method had been validated to have the ability to identify the damage occurrence and location. However, building a precise enough finite elemental model (FEM) for the test structure is still a huge challenge for this frequency-change-ratio based damage detection technique. In order to overcome this disadvantage and extend the application for frequencies in structural health monitoring area, a novel method was developed in this paper by combining the cross-model cross-mode (CMCM) model updating algorithm with the frequency-change-ratio based method. At first, assuming the physical parameters, including the element mass and stiffness, of the test structure had been known with a certain value, then an initial to-be-updated model with these assumed parameters was constructed according to the typical mass and stiffness distribution characteristic of shear buildings. After that, this to-be-updated model was updated using CMCM algorithm by combining with the measured frequencies of the actual structure when no damage was introduced. Thus, this updated model was regarded as a representation of the FEM model of actual structure, because their modal information were almost the same. Finally, based on this updated model, the frequency-change-ratio based method can be further proceed to realize the damage detection and localization. In order to verify the effectiveness of the developed method, a four-level shear building was numerically simulated and two actual shear structures, including a three-level shear model and an eight-story frame, were experimentally test in laboratory, and all the test results demonstrate that the developed method can identify the structural damage occurrence and location effectively, even only very limited modal frequencies of the test structure were provided.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.10 no.1
• /
• pp.92-99
• /
• 2005

To discriminate the provenance of shelf sediments in the East China Sea, textural and elemental compositions along with strontium isotopic ratio ($^{87}Sr/^{86}Sr$) were analyzed and compared with the sediments originated from Chinese rivers. The sediments in the study area are composed of fine-grained mud with a mean grain size of $47\;{\phi}$ and their $CaCO_3$, contents range from 3.9 to 11.5% (average 7.6%). In the study area, the content of most metallic elements are strongly constrained by sediment grain size (quartz dilution effect) and that of biogenic material and, thereby, their spatial distribution seems not enough for understanding sediment provenance in the study area. The muddy sediments of the Yangtze river have much lower $^{87}Sr/^{86}Sr$ ratio ($0.71197{\sim}0.71720$) than the Yellow Sea shelf muddy sediments which are supposed to be originated from the Huanghe river ($0.72126{\sim}0.72498$), suggesting the distribution pattern of $^{87}Sr/^{86}Sr$ ratios as a new tracer to discriminate the provenance of shelf sediments in the study area. Different source rock compositions and weathering processes between both drainage basins may account for the differences in $^{87}Sr/^{86}Sr$ ratio. Although the ratios show wide range, from 0.71445 to 0.72184 with an average 0.71747 in the study area, they are close to the values of the Yangtze river sediments, suggesting that the sediments were mainly originated from the Yangtze river. The previous studies on the dispersal pattern of modern sediments and the physico-chemical properties of seawater in the Yellow and East China seas support the possibility that the fine-grained Yangtze river sediments can reach to the East China Sea shelf as well as to the southeastern Yellow Sea.

• Journal of the Korean Chemical Society
• /
• v.58 no.3
• /
• pp.267-276
• /
• 2014

The collection of $PM_{10}$ and $PM_{2.5}$ fine particulate matter samples was made at the 1100 m site of Mt. Halla of Jeju Island, located at the atmospheric boundary layer (ABL) of background area, during the fall of 2012. Their ionic and elemental species were analyzed, in order to investigate the chemical compositions and size distribution characteristics. In $PM_{2.5}$ fine particles ($d_p$ < $2.5{\mu}m$), the concentrations of the secondary formed nss-$SO{_4}^{2-}$, $NH_4{^+}$ and $NO_3{^-}$ species were 4.84, 1.98, and $1.27{\mu}g/m^3$, respectively, showing 58.2% of the total $PM_{2.5}$ mass. On the other hand, their concentrations in $PM_{10-2.5}$ coarse particles (2.5 < $d_p$ < $10{\mu}m$) were 0.63, 0.21 and $1.10{\mu}g/m^3$, respectively, occupying 22.8% of the total $PM_{10-2.5}$ mass. The comparative study of size distribution has resulted that $NH_4{^+}$, nss-$SO{_4}^{2-}$, $K^+$ and $CH_3COO^-$ are mostly existed in fine particles, and $NO_3{^-}$ is distributed in both fine and coarse particles, but $Na^+$, $Cl^-$, $Mg^{2+}$ and nss-$Ca^{2+}$ are rich in coarse particle mode.

• Journal of Energy Engineering
• /
• v.17 no.1
• /
• pp.38-45
• /
• 2008

In this work, we investigated the variation of physical and chemical characteristics of solvent-insolubles and solvent-solubles in Canada's Athabasca oil sands by solvent-insolubles experiments. N-Heptane, n-Hexane, and n-Pentane were tested for solvents and asphaltenes were separated from maltenes by using a modified ASTM D 3279 method. Elemental analysis, boiling point distribution (SIMDIS), molecular weight distribution, heavy metal contents, API gravity, viscosity and SARA fractions were measured for thorough samples. The asphaltenes-removed maltenes contained less sulfur and heavy metal amounts and had lower molecular weight than the original bitumen. N-Pentane solvent could lower sulfur and heavy metal amounts, molecular weight, and viscosity of maltenes compared to the other solvents. Eventually, we confirmed that the obtained experimental data could be used as basic informations of bitumen upgrading processes for the production of SCO (synthetic crude oil).

• Bulletin of the Korean Chemical Society
• /
• v.35 no.11
• /
• pp.3289-3293
• /
• 2014

Femtosecond laser ablation (fs LA) was used in this study to identify pollution by heavy metals and the distribution of elemental nutrients at different rice milling ratios. Polished rice (degrees of milling of 3, 5, 7, 9, and 11) was collected from major Korean supermarkets and one sample thereof was selected. An internal quality control experiment was conducted using a rice flour certified reference material from the Korea Research Institute of Standards and Science (KRISS CRM) for the evaluation of the efficacy. To assess the effectiveness of the analysis method, the reliability was validated using a food analysis performance assessment scheme (FAPAS), with chili powder serving as an external quality control. The results of the analysis of the inorganic elements Ti, Ca, Al, Fe and Mn in white and brown rice with degrees of milling of 3, 5, 7, 9 and 11 using ICP-MS, ICP-OES and AAS revealed contents of 0.40, 49.2, 2.43, 5.36 and 10.3 mg/kg in white rice and 0.59, 78.0, 7.52, 11.0 and 18.5 mg/kg in brown rice, respectively. Among the elements, there were remarkable differences in the measured contents. By comparing the contents of the elements at different degrees of milling, Ti, Co, As, Ca, Al, Cu, Fe, and Mn were determined to be distributed on the surface of the rice grains, whereas the contents of Cd and Pb increased toward the center of the rice grains, and Si was evenly distributed. After the quantitative analysis of rice samples polished to different degrees of milling, Ca and Al, which were contained in large amounts, and Si were analyzed with specificity by fs LA. The results show that Ca and Al were distributed in the rice husk (protective covering of rice) and Si was distributed in all parts of the rice.

• Journal of Environmental Impact Assessment
• /
• v.28 no.2
• /
• pp.113-128
• /
• 2019

The concentration and coating thickness of black carbon (BC) were measured along with fine dust in the fall of 2018, at the Seoul Metropolitan Area Intensive Monitoring Station (SIMS). In fall, the concentration of $PM_{10}$ and $PM_{2.5}$ was $23{\pm}12.6{\mu}g/m^3$ and $12{\pm}5.8{\mu}g/m^3$, respectively, lower than that in other seasons. The BC level, measured using an Aethalometer, was $0.73{\pm}0.43{\mu}g/m^3$, while the levels of elemental carbon (EC) and refractory-BC (rBC), measured by semi-continuous carbon analyzer (SOCEC) and single particle soot photometer (SP2), were $0.34{\pm}0.18{\mu}g/m^3$ and $0.32{\pm}0.18{\mu}g/m^3$, respectively. As such, the concentration level differed according to the measurement method, but its time-series distribution and diurnal variation showed the same trends. The BC concentration at SIMS was primarily affected by automobiles with higher levels of BC during morning and evening commuting times due to increased traffic congestion. rBC, measured by SP2, had a peak concentration and coating thickness of 84 nm and 43 nm, respectively. Notably, the coating thickness had an inverse relationship with particle size.

• Korean Journal of Agricultural Science
• /
• v.38 no.1
• /
• pp.101-108
• /
• 2011

In forest work, working conditions are very hard to improve. The proper distribution of work time and good posture is believed to bring about direct improvements such as accident prevention. On this, this study has analyzed forest workers' posture and their working hours in order to improve their working conditions in stone channel work. Authors has chosen several core elements of stone channel work to focus on, which include stone masonry, excavation of bed, moving stone, directing work, choosing stone, and breaking stone. The ratio of real working time over total working time was shown as 84.6%. As for the time ratio of each elemental work over the real working time, the stone masonry was 60.4%, the directing work was 15.1%, moving stone was 12.1%, choosing stone was 7.1%, breaking stone was 3.3%, and excavation of bed was 2.0%. According to the analytical results provided by OWAS, the ratio of category III (Work posture has a distinctly harmful effect on the musculoskeletal system) has shown that moving stone turned out 65.2%, choosing stone was 61.5%, stone masonry was 46.1%, breaking stone was 14.3%, excavation of bed was 12.5% and directing work was 6.8%. Furthermore, the ratio of category IV (Work posture with an extremely harmful effect on the musculoskeletal system) has shown that excavation of bed turned out 37.5%, breaking stone was 28.6%, stone masonry was 27.3%, choosing stone was 7.7%, moving stone was 6.1% and directing working was 4.5%. These results are expected to be utilized for the improvement with respect to both working methods in the stone channel work and the workers' working posture.