• 비파괴검사학회지
• /
• 제27권2호
• /
• pp.173-182
• /
• 2007

콘크리트 구조물에 발생한 균열은 내구성과 사용성 측면의 문제가 발생할 수 있기 때문에 정기적으로 관리하여야 한다. 대부분의 균열 측정은 균열 현미경과 균열 게이지와 같은 장비를 이용하여 균열의 폭, 길이, 방향 등과 같은 균열의 특징을 육안조사나 수작업에 의해 수행되고 있다. 그러나 기존의 방법들은 시간과 인력이 많이 필요할 뿐만 아니라 계측자의 주관이 개입될 여지가 많다. 따라서 이 연구에서는 이미지 프로세싱과 인공신경회로망을 이용하여 콘크리트 표면 균열 평가 기법을 제시하고자 한다. 개발된 기법은 세부분(균열 검출, 균열 분석, 균열 패턴인식)으로 나누어진다. 개발된 기법의 유효성을 검증하기 위하여 실험을 수행하였고, 실험 결과 개발된 기법은 콘크리트 표면 균열을 효과적으로 검출, 분석할 수 있었고, 5가지 균열 패턴을 정확히 인식하였다.

• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.8-13
• /
• 2008

Emissions from automobiles have long been considered a prime source of pollutants involved in smog formation and ozone production. Especially VOCs are associated with serious environmental problems such as photo-chemical smog as well as human health effects. Since motor vehicles are a major source of VOCs, estimating of emission from mobile source is the most important factor to control VOCs. VOCs are emitted from various pollution like motor vehicles, mobile and stationary source that has characteristics of toxicity, cancer-causing, bio-accumulation, durability in air and diffusion can exert a bad influence upon human health and environment. However we don't have any standard or regulation about VOCs emissions. This study is summarized as VOCs emission characteristics from in-use light-duty diesel and LPG fueled vehicles. The vehicle exhaust-gas test mode is CVS cycle and nier-10 cycles that developed on EPA and National Institute of Environmental Research. TO-14 method (Toxic Organic) was chosen for VOCs analysis from EPA in USA. This study results will be useful when make a emission factor and rule making of emission standard about domestic VOCs emission for the improve to air condition.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.586-591
• /
• 2001

This research investigated the feasibility of the accelerated carbonation of cement waste forms with carbon dioxide in a supercritical state. Hydraulic cement has been used as a main solidification matrix for the immobilization of radioactive and/or hazardous wastes. As a result of the hydration reaction for major compounds of portland cement, portlandite (Ca(OH)$_2$) is present in the hydrated cement waste form. The chemical durability of a cement form is expected to increase by converting portlandite to the less soluble calcite (CaCO$_3$). For a faster reaction of portlandite with carbon dioxide, SCCD (supercritical carbon dioxide) rather than gaseous $CO_2$, in ambient pressure is used. The cement forms fabricated with an addition of slated lime or Na-bentonite were cured under ambient conditions for 28days and then treated with SCCD in an autoclave maintained at 34$^{\circ}C$ and 80atm. After SCCD treatment, the physicochemical properties of cement matrices were analyzed to evaluate the effectiveness of accelerated carbonation reaction. Conversion of parts of portlandite to calcite by the carbonation reaction with SCCD was verified by XRD (X-ray diffraction) analysis and the composition of portlandite and calcite was estimated using thermogravimetric (TG) data. After SCCD treatment, tile cement density slightly increased by about 1.5% regardless of the SCCD treatment time. The leaching behavior of cement, tested in accordance with an ISO leach test method at 7$0^{\circ}C$ for over 300 days, showed a proportional relationship to the square root of the leaching time, so the major leaching mechanism of cement matrix was diffusion controlled. The cumulative fraction leached (CFL) of calcium decreased by more than 50% after SCCD treatment. It might be concluded that the enhancement of the characteristics of a cement matrix by an accelerated carbonation reaction with SCCD is possible to some extent.

• 한국분말재료학회지
• /
• 제20권6호
• /
• pp.460-466
• /
• 2013

4 mol% Yttria-stabilized zirconia (4YSZ) coatings with $200{\mu}m$ thick are fabricated by Electron Beam Physical Vapor Deposition (EB-PVD) for thermal barrier coating (TBC). $150{\mu}m$ of NiCrAlY based bond coat is prepared by conventional APS (Air Plasma Spray) method on the NiCrCoAl alloy substrate before deposition of top coating. 4 mol% YSZ top coating shows typical tetragonal phase and columnar structure due to vapor phase deposition process. The adhesion strength of coating is measured about 40 MPa. There is no delamination or cracking of coatings after thermal cyclic fatigue and shock test at $850^{\circ}C$.

• 한국표면공학회지
• /
• 제49권6호
• /
• pp.530-538
• /
• 2016

There is a close relationship between the performance and the heat generation of the electronic device. Heat generation causes a significant degradation of the durability and/or efficiency of the device. It is necessary to have an effective method to release the generated heat. Based on demands of the printed circuit board (PCB) manufacturing, it is necessary to develop a robust and reliable plating technique for substrates with high thermal conductivity, such as alumina ($Al_2O_3$), aluminium nitride (AlN), and silicon nitride ($Si_3N_4$). In this study, the plating of metal layers on an insulating silicon nitride ($Si_3N_4$) ceramic substrate was developed. We formed a Pd-$TiO_2$ adhesion layer and used APTES(3-Aminopropyltriethoxysilane) to form OH groups on the surface and adhere the metal layer on the insulating $Si_3N_4$ substrate. We used an electroless Ni plating without sensitization/activation process, as Pd particles were nucleated on the $TiO_2$ layer. The electrical resistivity of Ni and Cu layers is $7.27{\times}10^{-5}$ and $1.32{\times}10^{-6}ohm-cm$ by 4 point prober, respectively. The adhesion strength is 2.506 N by scratch test.

• 대한기계학회논문집A
• /
• 제34권3호
• /
• pp.353-359
• /
• 2010

최근 환경문제로 인한 차량의 연료절감이 중요해지면서 수송산업에서도 대형 수송기계의 경량설계에 대한 필요성이 지속적으로 커지고 있다. 본 연구에서는, 고강도강으로 대체된 대형 평판 트레일러 프레임의 경량모델을 개발하기 위하여 구조해석을 수행하였다. 이를 위하여, 트레일러 프레임의 주요 설계변수들을 선정하고 다구찌 기법을 적용하여 응력, 처짐량 그리고 비틀림 강성에 대하여 최적화된 결과를 도출하였다. 또한, 도출된 경량설계안의 타당성을 검토하기 위하여 시작품을 제작하여 실제 내구시험을 수행하였다.

• 한국재료학회지
• /
• 제19권12호
• /
• pp.649-656
• /
• 2009

Inorganic oxide colloids dispersed in alcohol were applied to a stainless steel substrate to produce oxide coatings for the purpose of minimizing emissive thermal transfer. The microstructure, roughness, infrared emissive energy, and surface heat loss of the coated substrate were observed with a variation of the nano oxide sol and coating method. It was found that the indium tin oxide, antimony tin oxide, magnesium oxide, silica, titania sol coatings may reduce surface heat loss of the stainless steel at 300${\circ}C$. It was possible to suppress thermal oxidation of the substrate with the oxide sol coatings during an accelerated thermal durability test at 600${\circ}C$. The silica sol coating was most effective to suppress thermal oxidation at 600${\circ}C$, so that it is useful to prevent the increase of radiative surface heat loss as a heating element. Therefore, the inorganic oxide sol coatings may be applied to improve energy efficiency of the substrate as the heating element.

• 조명전기설비학회논문지
• /
• 제15권3호
• /
• pp.67-73
• /
• 2001

본 논문에서는 ZnO 피뢰기 소자에 대한 내구성 평가와 열화실험을 위한 저항분 누설전류 검출장치의 개발과 열화진단기법에 대하여 기술하였다. 저항분 누설전류는 ZnO 피뢰기 소자가 정상상태인지 불안정상태인지에 대한 판단의 지표로서 사용할 수 있다. 본 논문에서는 보상회로로 구성된 저항분 누설전류 측정시스템을 설계하여 구성하고, 실증실험으로서 ZnO 소자에 대한 저항분 누설전류의 측정과 고속프리에 변환기법(Fast Fourier transform)을 통해 저항분 누설전류의 주파수특성을 조사·분석하였다. 분석결과 제안한 저항분 누설전류의 측정 시스템은 실험실에서 산화아연 바리스터의 전기적·물성적 특성을 연구하고, 전력계통에 있어서 ZnO 피뢰기의 열화의 진단과 예측기술을 개발하는데 유용하게 활용할 수 있다.

• 한국안전학회지
• /
• 제34권4호
• /
• pp.1-5
• /
• 2019

In the field of combined cycle power generation, thermal barrier coating(TBC) protects the super-heat-resistant alloy, which forms the core component of the gas turbine, from high temperature exposure. As the turbine inlet temperature(TIT) increases, TBC is more important and durability performance is also important when considering maintenance cost and safety. Therefore, studies have been made on the fabrication method of TBC and super-heat-resistant alloy in order to improve the performance of the TBC. In recent years, due to excellent properties such as high temperature creep resistance and high temperature strength, turbine blade material have been replaced by a single crystal superalloy, however there is a lack of research on TBC applied to single crystal superalloy. In this study, to understand the isothermal degradation performance of the TBC applied to the single crystal superalloy, isothermal exposure test was conducted at various temperature to derive the delamination life. The growth curve of thermally grown oxide(TGO) layer was predicted to evaluate the isothermal degradation performance. Also, microstructural analysis was performed by scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDS) to determine the effect of mixed oxide formation on the delamination life.

• 대한금속재료학회지
• /
• 제49권8호
• /
• pp.596-600
• /
• 2011

Thermal degradation behavior of a $WO_3-TiO_2$ monolithic catalyst was investigated in terms of structural, morphological, and physico-chemical analyses. The catalyst with 4 wt.% $WO_3$ contents were prepared by a wet-impregnation method, and a durability test of the catalysts were performed in a temperature range between $400^{\circ}C$ and $800^{\circ}C$ for 3 h. An increase of thermal stress decreased the specific surface area, which was caused by grain growth and agglomeration of the catalyst particles. The phase transition from anatase to rutile occurred at around $800^{\circ}C$ and a decrease in the Brønsted acid sites was confirmed by structural analysis and physico-chemical analysis. A change in Brønsted acidity can affect to the catalytic efficiency; therefore, the thermal degradation behavior of the $WO_3-TiO_2$ catalyst could be explained by the transition to a stable rutile phase of $TiO_2$ and the decrease of specific surface area in the SCR catalyst.