• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 D
• /
• pp.2370-2373
• /
• 2004

In this paper we describe the design of a Dual-Redundant Power Controller(DRPC) for Control Rod Control System(CRCS). The CRCS also provides information regarding rod motion, rod position, and status of the Rod Control System. It has Hot/Stand-by type, and also has the function of fault detection for controller itself and power modules. We have implemented the various functions with the dual-redundant Power Controller. Due to the developed DRPC, we are assured that the commmecial use by this controller be made before long.

• 한국조명전기설비학회지:조명전기설비
• /
• 제9권5호
• /
• pp.71-79
• /
• 1995

This paper describes the design and implementation of dryer controller using the dual processor. This system has higher performance of system recovery from the noise than the existing single processor dryer. And in this paper temperature control method of Dryer using on-off fuzzy logic is proposed to improve the overshoot of temperature in dryer. Experimental results shows that the performance of fuzzy controller is better than that of controller based upon on-off control method.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1999년도 제14차 학술회의논문집
• /
• pp.317-320
• /
• 1999

A robust end time optimal conかof strategy for dual-stage servo system is presented. The time optimal trajectory for a mass-damper system is determined and given os a reference input to the servo system. The feedback controller is constructed so that the fine stage tracks the coarse stage errors and robustly designed as the“perturbation compensated sliding mode control(PCSMC)”law, a combination of slid-ing mode controller(SMC) and perturbation observer(PO). In addition, a null motion controller which regulates the fine stage at its neutral position is designed based on the“dynamic consistency”So, the overall dual-stage servo system exhibits the robust and time-optimal performance. The inherent merit and performance of the dual-stage system will be shown.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.530-533
• /
• 2001

Interleaved Dual Boost(IDB) converter can reduce current ripple, switching loss and harmonics without filter in input power line. Moreover, this improve power factor. In this paper, we will use the state average methode and small signal analysis at the Interleaved dual boost converter. 4-type controllers were designed by using control transfer function. The result of these controller simulations is analyzed and proposed a proper controller at IDB

• Journal of Electrical Engineering and Technology
• /
• 제6권1호
• /
• pp.133-138
• /
• 2011

This paper proposes a simple but robust self-tuning fuzzy logic controller for the speed regulation of a dual star induction machine based on indirect field oriented control. For feed the two star of this machine, two voltage source inverters based on sinus-triangular pulse-width modulation techniques are introduced. The simulation results show the robustness and good performance of the proposed controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.1327-1331
• /
• 1990

A new dual loop controller using color LCD bar graphs with LED back lights has been developed. An optional memory card is used to load or save the controller configuration, which may be a preprogrammed standard package or a user-programmed configuration, in addition to the built-in functions ready for user selection. The bar-graph display is selectable for single-loop or dual-loop use. A high grade of self-tuning functions using a modeling technique is built-in as standard. The controller can accommodate optional plug-in modules for thermocouples, communication, etc. All the options are fully field upgradable.

• 로봇학회논문지
• /
• 제13권1호
• /
• pp.72-78
• /
• 2018

This paper proposes a Dual Controller System for Precision Control (DCSPC) for control of the gripper. The DCSPC consists of two subsystems, CDSP (Controller based DSP) and CARM (Controller based ARM processor). The CDSP is developed on a DSP processor and controls the gripping motor and LVDT. In particular, the CARM is implemented using Linux and ARM processor according to recent research related to open-source. The robot for high-precision assembly is divided into the robot control and the gripper control section and controls CARM and CDSP systems respectively. In this paper, we also proposed and measured the performance of communication API. As a result, it is expected to recognize improvements in communication between CARM and the robot controller, and will continue to conduct relevant research among other commercial robot controllers.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.46-51
• /
• 2001

To reach high areal density, less track pitch is expected and more servo bandwidth is required. One approach to overcoming the problem is by using dual stage servo system. In this system, a voice coil motor (VCM) is used as the primary stage while a milliactuator is used as the secondary stage. We have suggested new milliactuator based on the shear mode of piezoelectric elements to drive the head suspension assembly. In this paper, we introduce controller design method, PQ method. PQ method reduces the controller design problem for DISO(dual-input/single-output) systems to two standard controller design problems for SISO(single-input/single-output) problems. The first part of PQ method directly address the issue of actuator output contribution, and the second part allows the use of traditional loop shaping to achieve the overall system performance. This paper shows how to employ the PQ method to meet aggressive close-loop performance specifications for a disk drive system with a VCM and piezoelectric milliactuator.

• 한국공작기계학회논문집
• /
• 제13권1호
• /
• pp.35-47
• /
• 2004

In this paper presents a new approach to the design and real-time implementation of fuzzy control system based-on digital signal processors(DSP:IMS320C80) in order to improve the precision and robustness for system of industrial robot(Dual-Arm with 8 joint Robot). The need to meet demanding control requirement in increasingly complex dynamical control systems under significant uncertainties, leads toward design of intelligent manipulation robots. The IMS320C80 is used in implementing real time fuzzy control to provide an enhanced motion control for robot manipulators. In this paper, a Self-Organizing Fuzzy Controller(SOFC) for the industrial robot manipulator with a actuator located at the base is studied. A fuzzy logic composed of linguistic conditional statements is employed by defining the relations of input-output variables of the controller. In the synthesis of a FLC(Fuzzy Logic Controller), one of the most difficult problems is the determination of linguistic control rules from the human operators. To overcome this difficult SOFC is proposed for a hierarchical control structure consisting of basic and high levels that modify control rules. The proposed SOFC scheme is simple in structure, Int in computation, and suitable for implementation of real-time control. Performance of the SOFC is illustrated by simulation and experimental results for a Dual-Arm robot with eight joints.

• 수산해양기술연구
• /
• 제31권3호
• /
• pp.264-271
• /
• 1995

제어전용 마이크로 프로세서와 PC간에, 본 연구에서 제안하는 이중 포트 램을 이용한 병렬처리 방식으로 하드웨어를 설계 제작하고, 제어응답실험을 행한 결과 기존의 범용 A/D & D/AC 카드로 수행하기 어려웠던 2개 이상의 제어 대상을 제어하고 모니터링 하는 작업을 원활히 수행할 수 있음을 확인하였다