• Steel and Composite Structures
• /
• v.32 no.5
• /
• pp.559-569
• /
• 2019

The bond strength between composite laminates and concrete is a key factor that controls the behavior of concrete members strengthened with fiber reinforced polymer (FRP) sheets, which can be affected by several parameters such as thermal stresses and surface preparation. This article presents the result of an experimental study on the bond strength between FRP sheets and concrete at ambient temperature after specimens had been exposed to elevated temperatures of up to $200^{\circ}C$. For this purpose, 30 specimens of plain concrete with dimensions of $150{\times}150{\times}350mm$ were prepared. Three different conventional surface preparation methods (sandblasting, wire brushing and hole drilling) were considered and compared with a new efficient method (fiber implantation). Deformation field during each experiment was monitored using particle image velocimetry. The results showed that, the specimens which were prepared by conventional surface preparation methods, preserved their bond integrity when exposed to temperature below glass transition temperature of epoxy resin (about $60^{\circ}C$). Beyond this temperature, the bond strength and stiffness decreased significantly (about 50%) in comparison with control specimens. However, the specimens prepared by the proposed method displayed higher bond strengths of up to 32% and 90% at $25^{\circ}C$ and $200^{\circ}C$, respectively.

• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.2977-2983
• /
• 2023

During normal operation, some parts of the fission product in the defective fuel rods can release into the primary loops in PWR and the escape rate coefficients are widely used to assess quantitatively the release behaviors of fission products in the industry. The escape rate coefficients have been standardized and have been validated by some drilling experiments before the 1970s. In the paper, the model to determine the escape rate coefficients of fission products has been established and the typical escape rate coefficients of noble gas and iodine have been deduced based on the measured radiochemical data in one operating PWR. The result shows that the apparent escape rate coefficients vary with the release-to-birth and decay constants for different fission products of the same element. In addition, it is found that the escape rate coefficients from the defective rod with large defects are much higher than the standard escape rate coefficients, i.e., averagely 4.4 times and 1.8 times for noble gas and iodine respectively. The enhanced release of fission products from the severe secondary hydriding of several defective fuel rods in one cycle may lead to the potential risk of the temporary shutdown of the operating reactors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.259-266
• /
• 2020

In this study, required drill bits and excavation methods were developed for an uneven drilling method that can solve the problem of performance degradation of rock bolts. The developed drill bit's excavation performance was verified using rock with a strength of 100 MPa or more. In addition, for the relative evaluation of the uneven excavation method, experimental specimens were prepared for models with and without irregularities, and tests were performed. As a result of the experiment, the model with unevenness exhibited an average critical draw resistance of 801.6 kN, which is about 1.7 times the value of 468.7 kN for the model without unevenness, thus confirming the effect sufficiently. Therefore, it is expected that the resistance performance will significantly increase despite an increase in the uneven hole diameter of 20 mm. In the future, the results of this study could be used as basic data when performing other studies using numerical analysis models and performance verification through experiments to obtain an optimized rock forming method.

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.410-415
• /
• 2001

Conventional Korean tunnel portals require a lot of overburden as, fer static reasons, about 1.5 to 2.0 times the tunnel diameter is needed for the height in order to achieve a sufficient arching effect. Thus, considerable movement of earth and support constructions are required which lead to undesirably large changes of and damage to the environment. With a massively designed pipe roof, tunnels with little overburden can be built. For the effective construction of a pipe roof as an advancing safeguarding method, the following properties are indispensable： stability, insensitivity to settling and drilling accuracy. With the AT casing system a new pipe roof method has been developed which on the one hand entirely combines the properties mentioned last, and which on the other hand permits safe, economical and environmentally friendly construction of tunnels at low overburden heights of 3 to 6 m.

• Tunnel and Underground Space
• /
• v.4 no.3
• /
• pp.237-249
• /
• 1994

A new type of cut method, called SK-cut, was developed in order to overcome the shortcomings of the conventional V-cut and Burn-cut blasting methods. Total 190 times of test blasts were performed for the evaluation of the efficiency of new blasting method. V-cut, Burn cut and SK-cut were compared by applying them to the excavation of main gallery and construction tunnel of underground oil storage cavern. Test results showed that excavation efficiency of the new method was increased by 5.9~9.8% and that specific charge was reduced to 71~92%.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.1-10
• /
• 2009

Based on recent studies, the side resistance of rock socketed drilled shafts was affected by unconfined compressive strength of rock, socket roughness, rock types and joints, and initial normal stress. Especially, the socket roughness was affected by rock types and joints, drilling methods, and diameters of pile. In this study, a new roughness measurement system (BKS-LRPS, Backyoung-KyungSung Laser Roughness Profiling System) usable in water was developed. Based on the laboratory model tests, an EMD (Effective Measurement Distances) according to various turbidity was proposed as EMD=$1149.2{\times}T^{-0.64}_b$.

• The Plant Pathology Journal
• /
• v.35 no.3
• /
• pp.234-242
• /
• 2019

Thirty-four strains of bacteria were isolated from Phellodendron amurense. Using Nectria haematococca as an indicator strain, the best strain, B18, was obtained by the growth rate method. The morphological, physiological and biochemical characteristics of strain B18 and its 16S DNA gene sequence were identified, and the biocontrol effect of strain B18 was assessed in pot and field tests, as well as in a field-control test. Drilling methods were used to determine the antibacterial activity of metabolites from strain B18 and their effects on the growth of pathogen mycelia and spores. The best bacteriostatic rate was 85.4%. B18 can hydrolyse starch and oxidize glucose but does not produce gas; a positive result was obtained in a gelatine liquefaction test. According to 16S DNA gene sequencing, strain B18 is Bacillus methylotrophicus (GenBank accession number: MG457759). The results of pot and field-control trials showed 98% disease control when inoculating $10^8cfu/ml$ of the strain. The disease control effect of the B18 culture liquid (concentrations of $10^8$, $2{\times}10^6$, $10^6$, $5{\times}10^5$ and $2.5{\times}10^5cfu/ml$) in the field-control test was higher than 80%, and the cure rate of the original delivery solution was 96%. Therefore, in the practical forestry production, a $2.5{\times}10^5cfu/ml$ culture liquidshould be applied in advance to achieve good control effects.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.21 no.1
• /
• pp.136-179
• /
• 1976

Effects of seeding pattern and rate on the yield and some agronomic characters of barley under different cultural conditions were observed at Suweon, Daejeon and Jinju during the barley growing season from 1972 to 1974. Plant height and culm length were increased by dense seeding, shading, heavy fertilization, moving location down to the lower latitude. The tiller number per plant, dry matter weight, leaf number on main stem, percentage of valid tillers, RGR, NAR, and $R_{A}$ were increased by heavy fertilization, sparse seeding, reduced furrow width and drilling likewise the length, width and angle of leaf. The newer cultivar had higher RGR and NAR. The higher yielding cultivars had higher potential for carbohydrate assimilating ability. Straw weight and grain yield were increased by dense seeding, reduced furrow width, drilling, heavier fertilization and moving the location to the south, and then decreased by shading and late seeding. High yield increase by drilling was found in late seeding. The optimum seeding rate for the yield increase were 15l/10a for furrow and 25l/10a for drilling. The spike number type cultivars were favourable for the sparse seeding and the spike weight type cultivars seemed to be suitable to the dense seeding, The repeatability of days to heading due to location and fertilizer level was higher than that of seeding time and seeding method. Repeatability of culm length was extremly high in seeding method and comparatively high in fertilizer level while low in location. The repeatability of yield due to location and seeding methods was comparatively high, but the tendency was different along with different cultivars. Also the repeatability of yield due to the fertilizer level was generally high except cultivar Haganemngi.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.35 no.1
• /
• pp.17-25
• /
• 2015

The following experiments were used to evaluate the effect of seeding method and pre-emergence herbicides on weed control and the production of the $sorghum{\times}sudangrass$ [sorghum bicolor (L.) Moench] hybrid under field and in vitro conditions. Under the in vitro condition, we evaluated how different kinds of herbicides affect the rate of seed germination and the growth of early seedlings in the $sorghum{\times}sudangrass$ hybrid treated with herbicides. Simazine, alachlor, and methabenzthiazuron were used, and their concentration levels were 0%, 40%, 70%, and 100%. The germination ratio of the seeds was reduced by the application of simazine, methabenzthiazuron, and alachlor compared with the control (distilled water). The alachlor application severely decreased the sorghum germination ratio. However, seed germination was not greatly influenced by the concentration level of the herbicides. Root and shoot length were increased in the following order: control > simazine > methabenzthiazuron > alachlor. Overall, alachlor significantly reduced root length more than shoot length. The differential tolerance of the $sorghum{\times}sudangrass$ hybrid to pre-emergence herbicides by seeding method was then tested under the field condition. The plants were severely injured by the alachlor application, leading to a great reduction in the number of stems. However, for the simazine and methabenzthiazuron applications the number of stems lost was slightly lower than it was for the alachlor and simazine + alachlor applications. In the seeding method, drilling was more effective in reducing herbicide injury than broadcasting. All of the herbicides effectively controlled weeds. The simazine and methabenzthiazuron applications showed a significantly higher dry matter (DM) yield. However, the alachlor and simazine + alachlor applications severely reduced the DM yield. This result suggests that the alachlor application has a significant effect on plant production. Similarly, the total digestible nutrient (TDN) yield was greatly reduced by the alachlor and simazine + alachlor applications. From the results presented above, we concluded that the yield of DM was the highest for broadcasting with no herbicide. and drilling was the most-effective way to reduce herbicide injury. The simazine application was the most-effective herbicide, showing the highest forage yield and TDN yield.

• Tunnel and Underground Space
• /
• v.5 no.4
• /
• pp.336-346
• /
• 1995

Geotechnical Information System (GTIS) for efficient management of three dimensional borehole data has been developed. Some problems were raised during the input process of borehole data, and alternative solutions were sought. According to the previous geotechnical reports, there is no unified weathering classification scheme. A criterion, 100 times/30cm from SPT, was turned out inappropriate to the discrimination of weathered rock from weathered soil. It has also been suggested that weathered soil, weathered rock, soft rock, and hard rock should be defined as CW, HW, MW, and SW~fresh condition. For better comparison of RQD, the use of NX size coring is recommended for the whole area although BX size coring has been used in excavated area. The limit of drilling depth up to 1 m from the top of surface of hard rock should be extended to avoid possible wrong interpretation of rock head due to the existence of corestone. The input data were analysed by geostatistical methods. It is found that the range in semivariogram is about 300m, and the variance of gneiss is greater than that of granite. It is because the granite data analysed came from almost single uniform rock mass(i.e.Seoul granite), but gneiss data came from the rock mass(i.e. Gyeonggi gneiss complex experienced several metamorphic metamorphic processes.