• Earthquakes and Structures
• /
• 제8권2호
• /
• pp.305-377
• /
• 2015

The problem of earthquake induced torsion in buildings is quite old and although it has received a lot of attention in the past several decades, it is still open. This is evident not only from the variability of the pertinent provisions in various modern codes but also from conflicting results debated in the literature. Most of the conducted research on this problem has been based on very simplified, highly idealized models of eccentric one-story systems, with single or double eccentricity and with load bearing elements of the shear beam type, sized only for earthquake action. Initially, elastic models were used but were gradually replaced by inelastic models, since building response under design level earthquakes is expected to be inelastic. Code provisions till today have been based mostly on results from one-story inelastic models or on results from elastic multistory idealizations. In the past decade, however, more accurate multi story inelastic building response has been studied using the well-known and far more accurate plastic hinge model for flexural members. On the basis of such research some interesting conclusions have been drawn, revising older views about the inelastic response of buildings based on one-story simplified model results. The present paper traces these developments and presents new findings that can explain long lasting controversies in this area and at the same time may raise questions about the adequacy of code provisions based on results from questionable models. To organize this review better it was necessary to group the various publications into a number of subtopics and within each subtopic to separate them into smaller groups according to the basic assumptions and/or limitations used. Capacity assessment of irregular buildings and new technologies to control torsional motion have also been included.

• 산업경영시스템학회지
• /
• 제39권4호
• /
• pp.60-66
• /
• 2016

Compound logistics is a service aimed to enhance logistics efficiency by supporting that shippers and consigners jointly use logistics facilities. Many of these services have taken place both domestically and internationally, but the joint logistics services for e-commerce have not been spread yet, since the number of the parcels that the consigners transact business is usually small. As one of meaningful ways to improve utilization of compound logistics, we propose a brokerage service for shipper and consigners based on the hybrid recommendation system using very well-known classification and clustering methods. The existing recommendation system has drawn a relatively low satisfaction as it brought about one-to-one matches between consignors and logistics vendors in that such matching constrains choice range of the users to one-to-one matching each other. However, the implemented hybrid recommendation system based brokerage agent service system can provide multiple choice options to mutual users with descending ranks, which is a result of the recommendation considering transaction preferences of the users. In addition, we applied feature selection methods in order to avoid inducing a meaningless large size recommendation model and reduce a simple model. Finally, we implemented the hybrid recommendation system based brokerage agent service system that shippers and consigners can join, which is the system having capability previously described functions such as feature selection and recommendation. As a result, it turns out that the proposed hybrid recommendation based brokerage service system showed the enhanced efficiency with respect to logistics management, compared to the existing one by reporting two round simulation results.

• 한국의류산업학회지
• /
• 제17권5호
• /
• pp.718-730
• /
• 2015

This study investigated the correlation between the level of consistency in fashion show models' appearance and design concept through a statistical and qualitative analysis of the S/S Paris Collection 2014. The following conclusions have been drawn in this study. First, the percentage of models of color was very low in regards to the physical appearance of models; in addition, there was a higher percentage of Caucasian models for collections with a high level of consistency in models' physical appearance. Collections with a high percentage of models of color indicate more casual design concepts and the promotion of diversity in racial background is considered more effective for street fashion. Second, collections with a high level of consistency in models' physical appearance tend to control various elements that constitute a physical appearance through more detailed planning and stage direction. Third, there is a tendency to reinforce design concepts by creating a consistency in the overall physical appearance of models. This affirms that their physical appearance is determined by brand (i.e. designer) and is used to maximize a design concept delivery. The results of this study suggests that the physical appearance of models must be determined in line with the design concept versus detailed planning that must consider audience perspectives as well as adjust the show's length and the interval between each model appearing on the stage.

• 대한기계학회논문집
• /
• 제15권1호
• /
• pp.252-261
• /
• 1991

본 연구에서는 2상 횡분류의 평균 유동특성을 비교적 정확히 예측할 수 있는 방법을 제시하는데 있다. 이를 위하여 2상 기체 분류속에 유입되는 자유흐름의 질량 유입을 Keffer와 Baines의 유입함수를 이용하기로 하며, 입자와 기체분류사이의 궤적 이탈을 고려하기로 한다. 이런 모델을 이용하여 2상 횡분류의 분출초기의 입자와 기 체분류의 속도비(particle to gas velocity ratio at the jet exit)가 유동에 미치는 영향을 알아보고자 한다.

• 대한치과교정학회지
• /
• 제35권3호
• /
• pp.238-249
• /
• 2005

악골부조화가 심할수록 기능향상을 위해 악골 및 치아 치조부에서의 보상반응이 현저해진다. 대표적인 현상으로 하악과두의 변위와 상악교합평면의 변화 등을 들 수 있다. 이러한 상하악골에서의 적응성 변화는 안모의 심미성과 교합의 기능 향상을 위해, 술후 안정성을 높이기 위해서 악교정수술을 통해 반드시 수정해야 할 요소이다 적절한 상악골 수술을 위해서 통상적으로 model surgery를 시행하여 왔으나 이의 단점을 보완하기 위해 Surgical Jaw Relator를 고안하였으며 이는 교합기의 mounting plate 대신에 부착함으로써 상하악 모형의 삼차원적 이동과 회전이 가능하도록 설계되어 있으며 기존의 모든 종류(Panadent. Sam, Denar, Hanau 등)의 교합기에 손쉽게 부착하여 수술용 스프린트의 제작 시간을 대폭 줄일 수 있는 장점이 있다 상악골 상방 이동이 필요한 하악전돌 증례와 상악골 하방 이동이 요구되는 하악후퇴 증례 등에 본 기구를 적용한 결과 양호한 수술 결과를 얻었으며, 이로써 정교한 상악 수술을 요하거나 명확한 수술 계획이 설정된 증례 등에서 본 기구를 적절하게 사용할 경우 수술용 스프린트를 효율적으로 제작하는데 다소 도움이 될 것으로 생각된다.

• 한국수자원학회논문집
• /
• 제43권1호
• /
• pp.95-104
• /
• 2010

최근 지표수의 취수원 다변화 및 수질에 대한 불신 등으로 강변여과 개발에 관심이 모아지고 있다. 선진국에서의 강변여과 개발은 150년 정도의 역사를 가지고 있으며, 우리나라에서도 지속적으로 증가하고 있는 용수수요에 안정적으로 대처하기 위한 원수 확보방안으로 강변여과에 대한 조사가 1990년대부터 시작되었고, 현재 낙동강을 중심으로 몇몇 지자체에서는 강변여과를 활용한 상수도 공급이 이루어지고 있다. 그러나 지금까지는 강변여과에 의한 개발가능량 산정과 관정개발에 연구가 집중되어 개발가능지 선정에 관한 체계적인 연구가 이루어지지 않고 있는 실정이다. 본 논문에서는 게임이론을 활용한 강변여과 개발 적지선정에 대해 연구하였다. 게임이론은 수학적 분석이론의 하나로 사회과학(특히 경제학)과 생물학, 공학, 컴퓨터과학 등에 적용되고 있으며, 본 연구에서는 강변여과 개발을 위한 적정 후보지 결정에 이용되었다. 제안된 정책모형은 확률적 접근을 시도한 새로운 방법론이며, 적지선정을 위한 효율적인 분석이 가능한 것으로 나타났다.

• 대한치과보철학회지
• /
• 제40권3호
• /
• pp.246-261
• /
• 2002

The screw loosening is one of the complications that happen frequently in dental implant prostheses. The purpose of this study was to evaluate the changes of reverse/loosening (opening) torque of the screw according to the surface modifications by sandblasting and 24K gold electroplating as well as to determine the possibility of the clinical use of a washer in dental implant. The reverse torque of 4 experimental conditions(control, sandblasted, use of washers, electroplasted) was measured by digital torque gauge (Model MGT50Z, Mark-10 Corp., 458 West John Street Hicksville, NY 11801 USA). Electronic torque controller (Nobel Biocare DEA 020) was used in fastening the gold screws into abutment replicas. Mixed Linear Model Analysis method was used for statistical analysis. To examine the changes of screw thread surface, microphotographs were taken by Olympus PME-3 metallurgic microscope (Olympus Optical Co. Ltd., Tokyo, Japan). Within the limitations of this study, the following results were drawn: 1. The surface modifications of the gold screws and the use of a washer have significantly affected the reverse torque value compared to the control group (P<0.01). 2. Sandblasting and electroplating treatments demonstrated significantly higher reverse torque value than that of control group. 3. The use of a washer may be one of the useful clinical methods that prevent the screw loosening. However, further studies are necessary for the material selection and design of the washer.

• 한국가구학회지
• /
• 제21권1호
• /
• pp.26-39
• /
• 2010

This is a leading study to replace the structural analysis methodology on the specific traditional joint by a numerical analysis. Tests were carried out to test the compressive methodologies with the numerical results. The Japanese larch was used as a sample. The Orthotropic property of wood was specifically considered for the finite element numerical analysis. Linear numerical analysis and non-linear numerical analysis for the BEAM element and the two SOLID elements of ANSYS were used to analyze the compressive performance. In addition, more finely divided elements were used to raise the accuracy of the numerical result. Finally, the statistically significant differences were tested between that of the analytical and numerical results. It could be concluded that the SOLID 64 element shows the most optimum result when the non-linear analysis with the more finely divided element was used. However, finely dividing of the element is a considerable time consuming process, and it is quite difficult to raise the accuracy of the non-linear numerical analysis. Therefore, if considering the vertical displacement to be of the only interest, the BEAM element is more efficient than the SOLID element because the BEAM element is reflected as a simple line, which is less time consuming and difficult in dividing the elements. But, the BEAM element cannot accurately model the knot as a strength defect factor which is an important property in the orthotropic property of wood. Therefore, the SOLID element should be used to model the strength defect factor, knot, as it can be efficiently applied on the structural size flexure member which could be more strongly effected by the knot. In addition, it is useful at times when the failure types of members are to be more closely investigated, as the SOLID element is able to examine the local stress distribution of the member. The conclusion drawn by this study is of the good concordance between analytical results and numerical results of compressive wood members, but how orthotropic properties should only be considered. The numerical analysis on the specific Korean traditional joints will be based on the current study results.

• 한국IT서비스학회지
• /
• 제10권4호
• /
• pp.171-189
• /
• 2011

KAs information and knowledge are increasingly becoming more important in the knowledge-driven society, knowledge management, as a very important management paradigm, is securing firm position in private and public sectors. Complying with this paradigm, government-funded research institutes in science-technology sector are actively utilizing knowledge management by employing knowledge management system and evaluating its applications' performance. The purpose of this study is to develop evaluation items and measurement indices to rationally measure knowledge management performance of the government-funded research institutes and to verify the feasibility of applying these evaluation items and indices. To achieve this research goal, the evaluation model of knowledge management performance was constructed by reviewing and integrating the existing studies, and subsequently, evaluation areas, evaluation items, measurement indices were derived from this evaluation model. Also, the feasibility analysis on the evaluation items and measurement indices was performed by means of FGI(Focus Group Interview) with the knowledge management experts belonging to Korean government-funded institutions in science-technology sector. The implications of this study are as follows : in theoretical perspective, this study has proposed a criterion frame to evaluate knowledge management performance, and has rationally drawn evaluation items and measurement indices from the criterion frame. And in practical perspective, this study has improved the validity and practicality of the measurement indices, which can lead to more reasonable and easier evaluation of knowledge management performance of the government-funded research institutes.

• 한국근적외분광분석학회:학술대회논문집
• /
• 한국근적외분광분석학회 2001년도 NIR-2001
• /
• pp.1614-1614
• /
• 2001

The sweetness (。Bix) of fruit is the main quality factor contributing to the fruit taste. The brix of the apple fruit can be measured non-destructively by near infrared (NIR) spectroscopy, allowing the sweetness grading of individual apple fruit. However, the fruit quality is influenced by various factors such as growing location, producing year, variety and harvest time etc., accordingly the robust NIR calibration is required. In this experimental results are presented the influence of two variations such as growing location and producing year of apple fruit in establishing of calibrations for sweetness, and developed a stable and highly accurate calibration. Apple fruit (Fuji) was collected every year from 1995 to 1997 in 3 different growing locations (Andong, Youngchun and Chungsong) of Kyungpook in Korea. NIR reflectance spectra of apple fruit were scanned in wavelength range of 1100∼2500nm using an InfraAlyzer 500C (Bran+Luebbe) with halogen lamp and PbS detector. The multiple linear regression and stepwise was carried out between the NIR raw spectra and the brix measured by refractometer to select the best regression equations. The calibration models by each growing district were well predicted to dependent sample set, but poorly predicted to independent sample set. Combined calibration model using data of three growing districts predicted reasonable well to a population set drawn from all growing districts(SEP = 0.69%, Bias=-0.075). The calibration models by each harvest year were not transferable across harvest year, however a combined calibration model using data of three harvest years was sufficiently robust to predict each sample sets(SEP = 0.53%, Bias = 0.004).