• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.4
• /
• pp.25-35
• /
• 2002

This work describes an 8b 200MHz time-interleaved subranging analog-to-digital converter (ADC) based on a single-poly digital CMOS process. Two fine ADCs for lower digital bits of the proposed ADC employ a time-sharing double-channel architecture to increase system speed and a new reference voltage switching scheme to reduce settling time of the reference voltages and chip area. The proposed intermeshed resistor string, which generates reference voltages for fine ADCs, improves linearity and settling time of the reference voltages simultaneously. The proposed sample- and-hold amplifier(SHA) is based on a highly linear common-drain amplifier and passive differential circuits to minimize power consumption and chip area with 8b accuracy and employs input dynamic common mode feedback circuits for high dynamic performance at a 200MHz sampling rate. A new encoding circuit in a coarse ADC simplifies the signal processing between the coarse ADC and two successive fine ADCs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.189-193
• /
• 2005

In this paper, we propose a direct conversion double-balanced down-converter fer MB-OFDM W system, which is implemented using $0.18\;{\mu}m$ CMOS technology and its measurement results are shown. The proposed down-converter adopts a resistive current-source instead of general transconductance stage using MOS transistor to achieve wideband characteristics over RF input frequency band $3\~5\;GHz$ with good gain flatness. The measured conversion gain is more than +3 dB, and gain flatness is less than 3 dB for three UWB channels. The dc consumption of this work is only 0.89 mA from 1.8 V power supply, leading to the low-power W application.

• Journal of Broadcast Engineering
• /
• v.20 no.5
• /
• pp.676-686
• /
• 2015

A 4D light field image is represented in traditional 2D spatial domain and additional 2D angular domain. The 4D light field has a resolution limitation both in spatial and angular domains since 4D signals are captured by 2D CMOS sensor with limited resolution. In this paper, we propose a dictionary learning-based superresolution algorithm in 4D light field domain to overcome the resolution limitation. The proposed algorithm performs dictionary learning using a large number of extracted 4D light field patches. Then, a high resolution light field image is reconstructed from a low resolution input using the learned dictionary. In this paper, we reconstruct a 4D light field image to have double resolution both in spatial and angular domains. Experimental result shows that the proposed method outperforms the traditional method for the test images captured by a commercial light field camera, i.e. Lytro.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.332-332
• /
• 2017

Rice ratooning is the cultural practices to produce easily second rice from the stubble left behind after the main-crop harvest. The main advantage of rice ratooning is that in areas where rice is the main crop, double crop of rice can be grown for additional returns. Three early ripened rice cultivars were tested for estimation their milled rice quality and starch characteristics from main and ratoon rice. The main crop was harvested at mass maturity, after which the tillers were mowed to stubbles of about 10 cm tall. And then it left without any further input until the ratooned plant was ready for harvest. Highly significant variations were detected in the milled rice quality between main and ratoon rice. Protein and amylose contents of ratoon rice were more increased than those of main rice. The Toyo value (gloss) of cooked rice of ratoon crop was measured also higher than that of main crop. It resulted from higher air temperature during grain ripening compared with that of ratoon crop. The mean temperature during ripened period of ratoon rice was favorable for optimal maturation for early ripened rice cultivars. Normalized chromatograms of branch chain length distribution of amylopectin are demonstrated a distinct difference between main and ratoon rice flour. Ratoon rice had higher amount of short chains than that of main crop rice starches. Microscopic examination of rice flours with scanning electron microscopy shows starch granule shapes affected by the cropping types, main and ratoon rice. It showed significant differences among rice starch granule shapes and in granule size between main and ratoon rice. Starch of ratoon rice had more neat and smaller granules than that of main rice.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.4
• /
• pp.319-324
• /
• 2018

In this paper, we designed and implemented a code conversion method between ISO/IEC 10646 and the multi-byte code set. The Universal Multiple-Octet Coded Character Set(UCS) provides codes for more than 65,000 characters, huge increase over ASCII's code capacity of 128 characters. It is applicable to the representation, transmission, interchange, processing, storage, input and presentation of the written form of the language throughout the world. Therefore, it is so important to guide on code conversion methods to their customers during customer systems are migrated to the environment which the UCS code system is used and/or the current code systems, i.e., ASCII PC code and EBCDIC host code, are used with the UCS together. Code conversion utility including the mapping table between the UCS and IBM new host code is shown for the purpose of the explanation of code conversion algorithm and its implementation in the system. The programs are successfully executed in the real system environments and so can be delivered to the customer during its migration stage from the UCS to the current IBM code system and vice versa.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.10
• /
• pp.2341-2349
• /
• 2015

The commonly used Goldschmidt's floating-point divider algorithm performs two multiplications in one iteration. In this paper, a tentative error corrected K'th Goldschmidt's floating-point number divider algorithm which performs K times multiplications in one iteration is proposed. Since the number of multiplications performed by the proposed algorithm is dependent on the input values, the average number of multiplications per an operation in single precision and double precision divider is derived from many reciprocal tables with varying sizes. In addition, an error correction algorithm, which consists of one multiplication and a decision, to get exact result in divider is proposed. Since the proposed algorithm only performs the multiplications until the error gets smaller than a given value, it can be used to improve the performance of a divider unit. Also, it can be used to construct optimized approximate reciprocal tables.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.103-106
• /
• 2012

A memory access method that data are read with different sequences with writing order is a simple but important procedure in many image compression standards, such as JPEG, MPEG1/2/4, H.264, and HEVC. For real time processing, double buffering is widely used using two block sized buffers, that accesses buffers concurrently with alternative way to read and write. In some cases like a transpose memory in 2D DCT with a simple and regular access order, a single buffering which requires only single block sized buffer can be used. This paper shows that even in complex access orders there is a regularity among updating orders within a finite turns, and suggested an effective implementation method using a single block sized buffer to process concurrent read/write operation with different access orders.

• Progress in Superconductivity
• /
• v.13 no.1
• /
• pp.1-6
• /
• 2011

Measurement of magnetic signals generated from electric activity of myocardium provides useful information for the functional diagnosis of heart diseases. Key technical component of the magnetocardiography (MCG) technology is SQUID. To measure MCG signals with high signal-to-noise ratio, sensitive SQUID magnetic field sensors are needed. Present magnetic field sensors based on Nb SQUIDs have field sensitivity good enough to measure most of MCG signals. However, for accurate measurement of fine signal pattern or detection of local atrial fibrillation signals, we may need higher field sensitivity. In addition to field sensitivity, economic aspect of the SQUID system is also important. To simplify the SQUID readout electronics, the output voltage or flux-to-voltage transfer of SQUID should be large enough so that direct measurement of SQUID output can be done using room-temperature preamplifiers. Double relaxation oscillation SQUID (DROS), having about 10 times larger flux-to-voltage transfers than those of DC-SQUIDs, was shown to be a good choice to make the electronics compact. For effective cancellation of external noise inside a thin economic shielded room, first-order axial gradiometer with high balance, simple structure and long-baseline is needed. We developed a technology to make the axial gradiometer compact using direct bonding of superconductive wires between pickup coil and input coil. Conventional insert has mechanical support to hold the gradiometer array, and the dewar neck has equal diameter with the dewar bottom. Boiling of the liquid He can generate mechanical vibrations in the gradiometer array due to mechanical connection structure. Elimination of the mechanical support, and direct mounting of the gradiometer array into the dewar bottom can reduce the dewar neck diameter, resulting in the reduction of liquid He consumption.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.509-516
• /
• 1999

In this paper, it is designed a microstrip U-slotted patch antenna with double resonances to enhance the bandwidth. In the design of an U-slotted patch antenna, there are considered the input impedance, the width of patch, the total length of the slot, the height of foam, the position of the probe and the radius of feed pin. The broadband behavior of antenna can be obtained by adjusting the length and width of the slot. The radiation from the antenna is linear polarized with the E-paine parallel to the vertical slots and the H plane parallel to horizontal slot. The radiation pattern, impedance locus, and VSWR of the antenna are calculated using "ENSEMBLE" software, and compared with the experimental results. Experimental results show that the bandwidth for VSWR $\le$ 2:1 is about 28.6%, a directivity 14.18dBi at 6.040GHz. 6.040GHz.

• Journal of Welding and Joining
• /
• v.20 no.3
• /
• pp.74-83
• /
• 2002

In order to investigate the hot cracking phenomena of the Inconel 690 overlay welds, the hot cracking test(modified Varestraint test) was performed by varying augmented strain and welding speed in GTAW. A total of five kinds of specimens was used in the hot cracking test. The specimens used were two kinds of one layer specimens that were composed of just Inconel 690 deposited metal and three kinds of double layer specimens that were composed with as upper part of Inconel 690 weld metal and lower part of SA508 cl.3 or STS 309L. The main results are as fo11ows: In the welds composed of just Inconel 690, as the augmented strain was more increased and the welding speed was more decreased, the extent of cracking was more increased. And these cracks were mainly solidification cracks, and liquation cracks were also observed partially in HAZ. And hot cracking susceptibily of Inconel 690 welds by using filler metals containing Nb were higher than that of the welds with Nb free. The hot cracking susceptibility of Inconel 690 weld metal was increased with dilution of SA 508 cl.3 and STS 309L, and the influence of SA 508 cl.3 was higher than that of 575 309L. The results of calculation of $TSC\Delta$ and $TLC\Delta$ in Inconel 690 weld metal changed by dilution with base metal or neighboring welds were agreed well with the results of hot cracking test in this study. Therefore, it was expected that the hot cracking was considerably decreased or prevented by using proper welding conditions such as lower heat input, filler metals, base metal and neighboring welds.