• Korean Chemical Engineering Research
• /
• v.57 no.2
• /
• pp.244-252
• /
• 2019

This study investigated the effect of addition of aromatics such as Toluene/LCO/resin on the coke depression and asphaltene conversion. The experiment was carried out with vacuum residue as a feedstock with Molybdenum dispersed catalysts under the slurry-phase hydrocracking condition (Temp. of $425^{\circ}C$, $H_2$ pressure of 80 bar at $80^{\circ}C$, reaction time of 4 hr, Mo-concentration of 500 ppm). As results, the coke reduction was shown to be similar irrespective of types of aromatics, while asphaltene was more converted to gas and maltene when LCO and resin with higher dipole moment were added. The addition of aromatics with change of reaction time showed no difference in terms of depression of coke formation. But the addition of LCO rather increased the coke yield after 2 hr. And it was found that asphaltene in liquid phase had the higher aromaticity index so that asphaltene is difficult to disperse in oil phase.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.2
• /
• pp.113-121
• /
• 2019

Single walled carbon nanotube (SWCNT) has been used as a material for reinforcing various advanced materials because it has superior mechanical properties. However, pure SWCNT that does not have any functional group has a hydrophobic character, and exists as bundles due to the strong Van der Waals attraction between each SWCNT. Due to these reasons, it is very difficult to disperse SWCNTs in the water. In this work, in order to use SWCNT for production of cementitious composites, SWCNT was first dispersed in water to make an aqueous solution. Sodium deoxycholate (DOC) and Sodium dodecyl sulfate (SDS) were chosen as surfactants, and the dosage of DOC and SDS were 2wt% and 1wt%, respectively. Sonication and ultracentrifugation were applied to separate each SWCNT and impurities. Using such processed SWCNT solutions, cement paste was prepared and its shear stress vs. strain rate relationship was studied. The yield stress and plastic viscosity of cement paste were obtained using Bingham model. According to the results in this work, cement pastes made with DOC and SDS showed similar rheological behavior to that of air entrained cement paste. While cement paste made with DOC 2 wt.% SWCNT solution showed similar rheological behavior to that of plain cement paste, cement paste made with SDS 1 wt.% SWCNT solution showed different rheological behavior showing much less yield stress than plain cement paste.

• Food Engineering Progress
• /
• v.21 no.3
• /
• pp.267-272
• /
• 2017

To improve dispersibility of cereal powder without additives, granulation of cereal powder was conducted using fluidized-bed granulator. Operation condition was sample 300 g, internal temperature $40^{\circ}C$, ventilation speed $30-90m^3/h$, inlet temperature $90^{\circ}C$ and spray pressure 2.5 bar. The amount of distilled water (20-45%) as binder, granulation time (10-15 min) and drying time (3-10 min) were controlled. Mean diameter over volume (Brouckere mean, $D_{4,3}$) was increased from $123{\mu}m$ to $263{\mu}m$ and dispersibility was improved from 73% to 92.25% at experiment conditions. Wettability (wetting time) was drastically decreased from 5,000 second to 7 second. Granulation of cereal powder did not affect sinkability and mean diameter over volume as wet analysis was about the same between raw and granulated cereals. Such phenomenon means that granulation with only water as binder enables cereal powder to disperse in water or milk without rapid sedimentation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.12
• /
• pp.23-32
• /
• 2020

This study investigated the thermal degradation and fading behavior of PTT dyed with vat dye and its dyeing ability. The PTT sample was dyed with vat dye using an acid treatment and pad-steam method to improve the dyeing performance. This method made dye particle nanosize and allowed it to penetrate the polymer material easily. The sample dyed using the pad-steam method showed level dyeing and enhanced dyeing affinity, compared to the batch-dyeing method. The degradation behavior of PTT dyed with vat dye after each heat and UV treatment was examined with the change in tensile strength or K/S value on the sample. The tensile strength and K/S values of the sample dyed with vat dye after the heat and UV treatment decreased with increasing temperature and exposure time. Although they showed high degradation under severe conditions, its rate constant was improved compared to the samples dyed with disperse dye. Consequently, acid treatment and the pad-steam method resulted in the introduction of vat dye on PTT. In addition, the PTT dyed with vat dye showed enhanced thermal and UV resistance because of their high molecular weight and chemical structure for stable adsorption behavior.

• Resources Recycling
• /
• v.31 no.4
• /
• pp.12-18
• /
• 2022

Korea depends on the import of raw materials such as iron ore and coal for the steel industry. These raw materials have a major impact on the cost, productivity, and quality competitiveness in the global steel industry. To secure the competitiveness of steel companies, it is necessary to reduce the country's dependence on raw materials. This can be achieved using byproducts with a high Fe content, which are primarily generated by the steel industry. These byproducts are available in the form of a very fine powder, which can disperse as dust when used directly in plant processes. Dust dispersion has a negative impact on the environment and can lead to the loss of raw materials. To enable the use of a wide range of Fe-containing byproducts, it is necessary to pretreat them in the form of larger aggregates such as pellets and briquettes. There are several methods to achieve such aggregates. There are two ways to produce briquettes: using a hot briquette, which supplies additional heat to produce briquettes, or using a cold briquette, which does not use heat. A method for producing cold briquettes using Fe-containing byproducts was investigated in this study. The yield ratio and briquette strength were examined under various manufacturing conditions.

• Korean Association of Arts Management
• /
• no.53
• /
• pp.153-177
• /
• 2020

Arts organizations commonly face a range of operational challenges, from a lack of skilled workers to limited financial resources and thus are dependent on subsidies from the government. Yet, to fully realize their mission arts organizations must both develop strategies to effectively utilize government support and seek a way forward that does not depend on public subsidies. Business diversification, a strategy from corporate management, entails the expansion of products and services, and entry into new industries, enabling companies to disperse risks and increase profits. We propose that business diversification can be effectively applied to arts organization to address the myriad operational difficulties they face. To understand how an arts organization might deploy business diversification we conducted a case study of an organization that is actively pursuing the strategy: Sanwoollim Theater. We interviewed staff members of Sanwoollim including the executive director, as well as selected audiences, to understand how the business diversification model was being applied at Sanwoollim. Our findings indicate that, in a complex arts and cultural space, business diversification is a fresh and flexible new strategy that can enable private cultural arts organizations to thrive sustainably. It is also evident that government support in the initial stages of the process encourages diversification and that successful private arts organizations will leverage government subsidies into a sustainable business plan.

• Geophysics and Geophysical Exploration
• /
• v.25 no.3
• /
• pp.99-108
• /
• 2022

Among induced polarization (IP) methods, spectral IP (SIP) uses alternating current as a transmission source to measure amplitudes and phase of complex electrical resistivity at each source frequency, which disperse with respect to source frequencies. The frequency dependence, which can be explained by a relaxation model such as Cole-Cole model or equivalent models, is analyzed to estimate SIP parameters from dispersion curves of complex resistivity employing multi-objective optimization (MOO). The estimation uses a generic algorithm to optimize two objective functions minimizing data misfits of amplitude and phase based on Cole-Cole model, which is most widely used to explain IP relaxation effects. The MOO-based estimation properly recovered Cole-Cole model parameters for synthetic examples but hardly fitted for the real laboratory measures ones, which have relatively smaller values of phases (less than about 10 mrad). Discrepancies between scales for data misfits of amplitude and phase, used as parameters of MOO method, and it is in necessity to employ other methods such as machine learning, which can deal with the discrepancies, to estimate SIP parameters from dispersion curves of complex resistivity.

• Korean Journal of Applied Biomechanics
• /
• v.33 no.1
• /
• pp.25-33
• /
• 2023

Objective: The purpose of this study was to investigate the differences in static arch height and ankle stability according to the preference for insole height and hardness in the arch area. Method: The study participants were 20 adult males (age: 22.7 ± 1.8 yrs., height: 175.3 ± 4.3 cm, body weight: 72.5 ± 7.7 kg). First, the arch heights of all subjects were measured in static postures (sitting and standing). The inversion and eversion movements of the ankle joint were analyzed during walking (1.3 m/s & 1.7 m/s) and running (2.7 m/s & 3.3 m/s). The variables (static arch height, and inversion and eversion angle of ankle joint) were compared by classifying groups according to the preference for the height and hardness of the arch of the insole. First, it was divided into a high arch insole preference group (HAG, n=8) and a low arch insole preference group (LAG, n=12) according to the preference for the arch height of the insole. Second, it was divided into a high hardness insole preference group (HHG, n=7), medium hardness insole preference group (MHG, n=7), and low hardness insole preference group (LHG, n=6), according to the preference for the arch hardness of the insole. Results: First, the range of motion (ROM) of inversion-eversion at the ankle joint during walking was statistically smaller in HAG than in LAG (p<.05). Second, the arch height change of HHG was statistically greater than that of MHG and LHG (p<.05). Conclusion: In the case of flexible flat feet with a large change in arch height, providing a high hardness arch insole that can disperse foot pressure can improve comfort. It was found that people with high medial and lateral sway of the ankle joint preferred a low arch insole, but it is necessary to differentiate and compare the insole heights of the arch part in detail. In addition, in the case of fast motion such as running, the preference for the arch height and hardness of the insole was not related to the static arch height and ankle stability.

• The Korean Journal of Franchise Management
• /
• v.5 no.1
• /
• pp.143-160
• /
• 2014

This study focuses that the business starters can refer to this study, select better franchise headquarter and make the franchise member agreement. The most concerned part for the people who want to open franchise shop is what brand is reliable and safe to them. I have analyzed disclosure report that contains overall information of franchise headquarters and researched 300 franchise shops as sample. I drew the conclusion of the decision factors of franchise member agreement, overlooked demographical status by frequency analysis with SPSS 18.0 and performed disperse analysis to examine the decision factors of franchise member agreement and the difference between sex, service type, shop size and income level. In conclusion, the most concerned factor for the franchise agreement is sales management. Sex, shop size and income level are not meaningful factors, but the cost and training management factors are considered differently based on the service type. I hope 1) this study can be utilized for the franchise business starters judge and refer information level provided by the headquarters and make a successful franchise shop business. 2) this study can make solid relationship between franchise members and present a long term vision to them. Finally, this study can be a foundation to promote franchise field through making and supplementing the law of promoting proficient and good franchise headquarters and fairness of franchise transaction and franchise encouragement.

• Journal of Bio-Environment Control
• /
• v.22 no.4
• /
• pp.341-348
• /
• 2013

Maintenance of adequate soil tension or content during the period of crop growth is necessary to support optimum plant growth and yields. A better understanding of soil tension and content for precision irrigation would allow optimal soil water condition to crops and minimize the adverse effects of water stress on crop growth and development. This research reports on a comparison of soil water tension and content variations in differently textured soils over time under drip irrigation using two different water management methods, i.e. pulse time and required water irrigation methods. The pulse time-based irrigation was performed by turning the solenoid valve on and off for preset times to allow the wetting front to disperse in root zone before additional water was applied. The required water estimation method was a new water control logic designed by Rural Development Administration that applies the amount of water required based on a conversion of the measured water tension into water content. The use of the pulse time irrigation method under drip irrigation at a high tension of -20 kPa and high temperatures over $30^{\circ}C$ was not successful at maintaining moisture tensions within an appropriate range of 5 kPa because the preset irrigation times used for water control could not compensate for the change in evapotranspiration during day and night. The response time and pattern of water contents for all of the tested soils measured with capacitance-based sensor probes were faster and more direct than those of water tensions measured with porous and ceramic cup-based tensiometers when water was applied, indicating water content would be a better control variable for automatic irrigation. The required water estimation-based irrigation method provided relatively stable control of moisture tension, even though somewhat lower tension values were obtained as compared to the target tension of -20 kPa, indicating that growers could expect to be effective in controlling low tensions ranging from -10 to -20 kPa with the required water estimation system.