• Journal of Convergence for Information Technology
• /
• v.11 no.2
• /
• pp.117-123
• /
• 2021

The effects of electrolyte concentration on the electrochemical properties of Fe4[Fe(CN6)]3(FeHCF) as a novel active material for the electrode of aqueous zinc-ion batteries was investigated. The electrochemical reactions and structural stability of the FeHCF electrode were significantly affected by the electrolyte concentration. In the electrolyte solutions of 1.0-7.0 mol dm-3, the charge-discharge capacities increased with increasing electrolyte concentration, however gradually decreased as the cycle progressed. On the other hand, in the 9.0 mol dm-3 electrolyte solution, the initial capacity was relatively small, however showed good cyclability. Additionally, the FeHCF electrode after five cycles in the former electrolyte solutions, had a change in crystal structure, whereas there was no change in the latter electrolyte solution. This suggests that the performance of the FeHCF electrode is greatly influenced by the hydration structure of zinc ions present in electrolyte solutions.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.3
• /
• pp.123-129
• /
• 1999

Initial electrochemical characteristics of $LiCoO_2$ electrode for lithium ion battery with various content of super s black as conductive material were evaluated through the charge/discharge with the potential range of 4.3V to 2.0V versus $Li^+/Li^+$. The rate of C/4 and C/2 by the 3 electrode test cell composed with an electrolytic solution of 1 mol/l $LiPF_6/EC+DEC(1:3\;by\; weight)$. Lithium was used as reference electrode. High impedance charge behavior was observed at early stage of charge. In the case of $3\%w/w$ of super s black as conductive material, the specific resistance of the high impedance releasing was $3.82\;{\Omega}\;{\cdot}\;g-LiCoCo_2$ at the current density of $0.5 mA/cm^2$, which corresponds 7 times of the specific resistance of electrode $(0.728 g-LiCoO_2)$. At second charge, the specific resistance of the high impedance releasing was 63 mn · g-Lico02, which corresponds 12eio of the specific resistance of electrode and only $1.7\%$ of that of the first charge. The first charge and discharge specific capacities at C/4 rate were 160-161 and $153\~155mAh/g-LiCoO_2$, respectively, to lead $95.4\~96.4\%$ of coulombic efficiencies and ca. $6 mAh/g-LiCoO_2$ of initial irreversible specific capacity. Specific resistance at the end of charge and rest showed low value at content of super s black between 2 and $7\%w/w$, which agreed with characteristics of irreversible specific capacity. Capacity densities were reduced by the increasing the content of conductive material. They were 447 and 431mAh/ml when 2 and $2.9\%w/w$ of super s black were used, respectively, at the rate of C/4.

• Journal of Wetlands Research
• /
• v.17 no.3
• /
• pp.221-227
• /
• 2015

Urbanization increases the impervious cover, which affects the discharge of stormwater runoff and non-point source pollutants to the waterbodies. In order to improve the water quality and restore the aqua-ecosystem, the Ministry of Environment (MOE), Korea MOE introduced the Low Impact Development(LID) techniques on development projects. Therefore, research was performed to develop the bioretention technology for managing the stormwater runoff from urban areas. The test-bed was established on 2013 up to evaluate the performance of pollutant and runoff reduction. A total of 11 storm events have been monitored from November 2013 to present. Even though the SA/CA (surface area of bioretention/catchment area) is approximately 2.2%, the facility shows high pollutant and runoff reduction during storm events by increasing retention and infiltration capacities. The bioretention shows a 100% total runoff reduction at 0mm < R < 10mm rainfall range and more than 90% of runoff reduction at a rainfall range of 10mm < R < 20mm. Due to runoff volume reduction, more than 90% of nonpoint source pollutant were also removed by the bioretention.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.2
• /
• pp.85-90
• /
• 2013

Graphite is a commercial anode material to have the specific capacity of 372 mAh/g and the true density of 2.2 g/ml. Many effort had been pouring to find out the better material than graphite. Good candidates are silicon, tin, etc. Zinc is also a plausible candidate to have the specific capacity of 412 mAh/g and the true density of 7.14 g/ml. In this study, the Zn based anode material including indium and nickel as minor additives was synthesised. In order to get the homogeneouly mixed Zn-In-Ni composite material, the sol-gel method was used. The anode prepared by Zn-In-Ni composite material has the $1^{st}$ specific capacity of 910 mAh/g. Through prolonged charge-discharge cycling, the specific capacities were reduced to 365 (at $31^{st}$ cycle) and 378 mAh/g (at $62^{th}$ cycle). The $1^{st}$ Ah efficiency was 45% and Ah efficiencies were exhibited at the prolonged cycle.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.1
• /
• pp.1-8
• /
• 2016

Capacity of layered lithium nickel-cobalt-manganese oxide ($LiNi_{1-x-y}Co_xMn_yO_2$) cathode material can increase by raising the charge cut-off voltage above 4.3 V vs. $Li/Li^+$, but it is limited due to anodic instability of conventional electrolyte. We have been screening and evaluating various sulfone-based compounds of dimethyl sulfone (DMS), diethyl sulfone (DES), ethyl methyl sulfone (EMS) as electrolyte additives for high-voltage applications. Here we report improved cycling performance of $LiNi_{0.5}Co_{0.2}Mn_{0.3}O_2$ cathode by the use of dimethyl sulfone (DMS) additive under an aggressive charge condition of 4.6 V, compared to that in conventional electrolyte, and cathode-electrolyte interfacial reaction behavior. The cathode with DMS delivered discharge capacities of $198-173mAhg^{-1}$ over 50 cycles and capacity retention of 84%. Surface analysis results indicate that DMS induces to form a surface protective film at the cathode and inhibit metal-dissolution, which is correlated to improved high-voltage cycling performance.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.4
• /
• pp.787-798
• /
• 2017

This is a study on characteristics according to the material of sheet-type mask packs being sold on the market. The absorption capacities of water soluble components such as purified water, 1.3-propanediol, 1.3-butylene glycol, glycerine, and hyaluronic acid are compared with that of various oils including cyclomethicone, dimethicone, phytosqualane, caprylic capryl triglyceride, grape seed oil, and macadamia nut oil. As a result, all of the water soluble components except purified water showed higher moisture absorption capacity as the viscosity increased. And in case of oil, all oil showed higher oil absorption capacity according to the viscosity. During this test, the mask sheets with the type of acetic acid fermented bio-cellulose showed 500~1,000 times or more absorption capacity on water soluble wetting agent or all oils, which is due to the fine mesh structure seen in the 5,000x enlarged photograph at surface structure. This mesh structure was well recognized on the cross section and these structural features enhance the absorption capacity of water and oil. It is also believed that largely contained water-soluble components and oils facilitate the discharge over time. In addition, since each mask sheet shows their characteristics according to their material, it is intended to be a basic research for manufacturing mask packs good for skin.

• Korean Chemical Engineering Research
• /
• v.56 no.6
• /
• pp.819-825
• /
• 2018

Porous nanofibers comprising hollow ${\alpha}-Fe_2O_3$ nanospheres were prepared by applying both template method and Kirkendall diffusion effect to electrospinning process. During heat-treatment processes, the solid Fe nano-metals formed by initial heat-treatment in the carbon matrix were converted into the hollow structured ${\alpha}-Fe_2O_3$ nanospheres. In particular, PS nanobeads added in the spinning solution were decomposed and formed numerous channels in the composite, which served as a good pathway for Kirkendall diffusion gas. The resulting porous nanofibers comprising hollow ${\alpha}-Fe_2O_3$ nanospheres were applied as an anode material for lithium-ion batteries. The discharge capacities of the nanofibers for the 30th cycle at a high current density of $1.0A\;g^{-1}$ was $776mA\;h\;g^{-1}$. The good lithium ion storage property was attributed to the synergetic effects of the hollow ${\alpha}-Fe_2O_3$ nanospheres and the interstitial nanovoids between the nanospheres. The synthetic method proposed in this study could be applied to the preparation of porous nanofibers comprising hollow nanospheres with various composition for various applications, including energy storage.

• Korean Journal of Clinical Laboratory Science
• /
• v.51 no.2
• /
• pp.164-170
• /
• 2019

The absorption and release capacities, survival efficiency, and recovery rates of five kinds of transport media were evaluated based on the swab elution method (Quantitative) of CLSI (Clinical and Laboratory Standards Institute) M40-A2. Liquid media showed mostly better results than semi-solid media in the three evaluations. The flocked swabs had better ability to absorption and discharge bacteria than the standard swabs. The liquid medium (S4) had the best survival efficiency. Pneumococcal strains with poor growth had a higher survival efficiency and recovery rate in liquid media (S4, S5). The results of microbial recovery showed that S. pyogenes met all the CLSI standards in all media. S. pneumoniae was inadequate in the semi- solid media (S2, S3) and all the remaining media met the criteria. H. influenzae was unsuitable in semi-solid media (S1, S3) and met the criteria in semi-solid medium (S2) and liquid medium (S4, S5). The viability of the H. influenzae, pneumococcal strain causing respiratory disease, was poor in most media. Overgrowth of P. aeruginosa was observed at room temperature. The combination of liquid medium and flocked swab confirmed the best results in the three evaluation methods.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.4
• /
• pp.99-107
• /
• 2017

This paper proposes a battery model coefficient correction method for improving the accuracy of existing lithium battery equivalent models. BMS(battery management system) has been researched and developed to minimize shortening of battery life by keeping SOC(state of charge) and state of charge of lithium battery used in various industrial fields such as EV. However, the cell balancing operation based on the battery cell voltage can not follow the SOC change due to the internal resistance and the capacitor. Various battery equivalent models have been studied for estimation of battery SOC according to the internal resistance of the battery and capacitors. However, it is difficult to apply the same to all the batteries, and it tis difficult to estimate the battery state in the transient state. The existing battery electrical equivalent model study simulates charging and discharging dynamic characteristics of one kind of battery with error rate of 5~10% and it is not suitable to apply to actual battery having different electric characteristics. Therefore, this paper proposes a battery model coefficient correction algorithm that is suitable for real battery operating environments with different models and capacities, and can simulate dynamic characteristics with an error rate of less than 5%. To verify proposed battery model coefficient calibration method, a lithium battery of 3.7V rated voltage, 280 mAh, 1600 mAh capacity used, and a two stage RC tank model was used as an electrical equivalent model of a lithium battery. The battery charge/discharge test and model verification were performed using four C-rate of 0.25C, 0.5C, 0.75C, and 1C. The proposed battery model coefficient correction algorithm was applied to two battery models, The error rate of the discharge characteristics and the transient state characteristics is 2.13% at the maximum.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.3
• /
• pp.172-180
• /
• 2012

The $LiMn_2O_4$ cathodes for lithium ion battery were synthesized from various precursors of manganese oxides and manganese hydroxides. As the first step, nanosized precursors such as ${\alpha}-MnO_2$ (nano-sticks), ${\beta}-MnO_2$ (nano-rods), $Mn_3O_4$ (nano-octahedra), amorphous $MnO_2$(nano-spheres), and $Mn(OH)_2$ (nano-plates) were prepared by a hydrothermal or a precipitation method. Spinel $LiMn_2O_4$ with various sizes and shapes were finally synthesized by a solid-state reaction method from the manganese precursors and LiOH. Nano-sized (500 nm) octahedron $LiMn_2O_4$ showed high capacities of 107 mAh $g^{-1}$ and 99 mAh $g^{-1}$ at 1 C- and 50 C-rate, respectively. Three dimensional octahedral crystallites exhibit superior electrochemical characteristics to the other one-dimensional and two-dimensional shaped $LiMn_2O_4$ nanoparticles. After 500 consecutive charge discharge battery cycles at 10 C-rate with the nano-octahedron $LiMn_2O_4$ cathode, the capacity retention of 95% was observed, which is far better than any other morphologies studied in this work.