• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1778-1780
• /
• 2004

Microwave heating system of KSTAR consists of ECH and LHCD. ECH and LHCD offer the reliability of operation in the beginning of plasma formation and non-inductive current drive for long time steady state operation with maintaining MHD stability, respectively. LHCD demands 5 GHz of frequency and consists of c-band waveguide, 4-port circuitor, dry dummy load, dual directional coupler, E-bend, arc detector. Our system is a lineup type pulse modulator that has 45 kV of output pulse voltage, 90 A of pulse current, 4 us of pulse width. 1:4 step-up pulse transformer, 7 stages of PFN and thyratron tube (E2V, CX1191D) are used in this modulator. The purpose of this paper is to show the modulator design and experimental result.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1275-1277
• /
• 1995

We designed and constructed an extremly high power s-band traveling wave resonator for the test of high power microwave components using 80MW pulsed klystron with $4{\mu}s$ pulse width. The 10dB directional coupler for the input power coupling was used, and the ring consists of phase shifter, tuner, H-band, and other microwave components. The designed total electrical length of the system is 10 times of the waveguide wavelength, ${\lambda}_g$=15.3cm, and the measured total insertion loss is 0.15dB. The low power test measurment showed the power multiplication of 14.69. The design goal is to achieve the peak power of 300MW, pulse width $4{\mu}s$ with 30 pulse repetition rate. In this article we discuss the treveling wave resonant ring constructed at the PAL laboratory together with the test results.

• Korean Journal of Optics and Photonics
• /
• v.11 no.6
• /
• pp.423-428
• /
• 2000

We have demonstrated a -8 dB additional reduction in the intensity sidelobe of an apodized-interaction-strength guide-wave acousto-optic filter with a center passband of 1551.6 nm. Acoustic-intensity weighting was achieved by launching a surface acoustic wave (SAW) beam in a straight acoustic waveguide, and gradually transferring this SAW intensity to the active device, and back out, by evanescent-wave coupling across a 50 !lm barrier over a 19 rom interaction length. The intensity sidelobe was -4.27 dB for an unapodized filter with abmpt onset and cutoff of the interaction, but sidelobes were reduced to at most -12.68 dB for a SAW intensity with raised-cosine weighting. The RF driving power was 17.78 mW. A linear tuning rate of 8.86 nmIMHz and a spectral width of -1.7 nm were demonstrated. rated.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.9
• /
• pp.93-99
• /
• 1998

A novel four-channel narrowband wavelength demultiplexer using integrated four vertical directional coupler structures is proposed and theoretically investigated. Four ridge waveguide with different ridge width are vertically coupled to a strip-loaded waveguide which results four different wavelengths filtered out to each ridge waveguide. In order to reduce the side-lobes, the coupling coefficients are varied along the propagation direction. The spectral responses of channels were found to be quite uniform. An average channel spacing of 7 nm with power coupling efficiency of ~90%, 3-dB passband width of 2 nm, and 20 dB side-lobe suppression ratio was achieved.

• Korean Journal of Optics and Photonics
• /
• v.10 no.1
• /
• pp.40-46
• /
• 1999

We present a new modified effective index method which can be used to analyze lightwave circuit devices in 3-dimensional structure fast and accruatly using 2-dimensional BPM (beam propagating method). This method can analyze the devices with the cross-section of rectangular, ridge, or similar shapes accurately but more quickly than the 3-dimensional BPM, which is impractical to use on account of long calculating time. As an example, we showed that the calculation error of coupling length in a directional coupler by this method is significantly less than the 2-dimensional BPM using the effective index method.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.4 no.3
• /
• pp.45-53
• /
• 1993

The shielding effectiveness of materials is determined by measuring the ratio of the incident electromagnetic power to that which passes through the material under test. The measurement system is constructed using several test fixtures, tracking generator, spectrum analyzer, step attenuator, RF switches, and amplifiers, etc.. The automation of measurements is completed using a personal computer. Especially, incident power, reflected power, and transmitted power are measured with only one spectrum analyzer using a dual directional coupler and RF switches. Therefore the system is to be used in design of shielding materials, as well as shielding effectiveness measurements. This system has dynamic range of more than 120 dB in the frequency range of 10 MHz to 1 GHz, and it can be used to measure shielding effectiveness of composite materials.

• Journal of electromagnetic engineering and science
• /
• v.13 no.1
• /
• pp.54-61
• /
• 2013

An equivalent model has been developed to estimate the electromagnetic immunity for integrated circuits under a complex electromagnetic environment. The complete model is based on the characteristics of the equipment and physical configuration of the device under test (DUT) and describes the measurement setup as well as the target integrated circuits under test, the corresponding package, and a specially designed printed circuit board. The advantage of the proposed model is that it can be applied to a SPICE-like simulator and the immunity of the integrated circuits can be easily achieved without costly and time-consuming measurements. After simulation, measurements were performed to verify the accuracy of the equivalent model for immunity prediction. The improvement of measurement accuracy due to the added effect of a bi-directional coupler in the test setup is also addressed.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.1
• /
• pp.74-82
• /
• 1999

We proposed an efficient beam Propagation Method(BPM) algorithm for 3-D analysis, which can handle great amount of data on PC efficiently. The new algorithm, which is an expanded version of DuFort-Frankel algorithm for 3-D analysis, can reduce the number of computations for a given BPM analysis. The algorithm was applied to a rib-type directional coupler to find the same results as those from the coupled mode theory.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2B
• /
• pp.167-173
• /
• 2004

This paper reports on the development of a 60㎓ wide bandwidth wireless transceiver using NRD waveguide. We fabricated a wireless transceiver using NRD waveguide, which consists of a 3 dB directional coupler, a bandpass filter, a Gunn oscillator, an ASK modulator, and a Balanced Mixer. The new transceiver is capable of transmitting an output power of 10mW to a distance of more than 1 Km, operating in 60㎓ frequency and bandwidth of 2㎓. The value of BER reached approximately 10 when the transceiver was tested at the 155.52Mbps ATM(OC 3) at the communication distance of 1 km. It demonstrated an impressively stable transmission feature of BER l0$^{6}$ even in the heavy rainfall.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.5C
• /
• pp.530-534
• /
• 2002

In the thesis, For improving the Stability of VCHRO(Voltage Controlled Hair-pin Resonator Oscillator) the new structure using the parallel feedback of the second harmonic is proposed for self-phase locking effect. This module is composed of wilkinson divider, frequency doubler, directional coupler, and bandpass filter using a hair-pin resonator, which are integrated into miniaturized hybrid circuit. The module exhibits output power of 2.5 dBm at 19.5 GHz, -29.83 dBc fundamental frequency suppression and -76.52 dBc/Hz phase noise at 10 kHz offset frequency from carrier of center frequency 19.5 GHz.