• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.83-87
• /
• 2022

Recently, as the thickness of the semiconductor package becomes thinner, warpage has become a major issue. Since the warpage is caused by differences in material properties between package components, it is essential to precisely evaluate the material properties of the EMC(Epoxy molding compound), one of the main components, to predict the warpage accurately. Especially, the cure shrinkage of the EMC is generated during the curing process, and among them, the effective cure shrinkage that occurs after the gelation point is a key factor in warpage. In this study, the gelation point of the EMC was defined from the dissipation factor measured using the dielectric sensor during the curing process similar with actual semiconductor package. In addition, DSC (Differential scanning calorimetry) test and rheometer test were conducted to analyze the dielectrometry measurement. As a result, the dielectrometry was verified to be an effective method for monitoring the curing status of the EMC. Simultaneously, the strain transition of the EMC during the curing process was measured using the FBG (Fiber Bragg grating) sensor. From these results, the effective cure shrinkage of the EMC during the curing process was measured.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.10
• /
• pp.141-149
• /
• 2007

This paper introduce to improve the reliability of the expected service life and the insulation condition evaluation of the high voltage induction motors by assessing, comparing and analyzing the correlation between the dielectric properties of the off-line insulation diagnostic test and dielectric strength on the insulation breakdown test. The insulation diagnostic tests include insulation resistance, polarization index(P.I.), dissipation factor($tan{\delta}$), maximum partial discharges($Q_{max}$) and AC breakdown test. This study evaluated the correlation between insulation diagnostic test and AC breakdown test for stator winding of high voltage induction motor. On the basis of these test results, we expect that this study can be used for effectively assessing the results of insulation diagnostic tests for similar class induction motors in service at industrial field.

• Korean Journal of Materials Research
• /
• v.18 no.7
• /
• pp.373-378
• /
• 2008

$Ba(Ti,Sn)O_3$ thin films, for use as dielectrics for MLCCs, were grown from Sn doped BaTiO3 sources by e-beam evaporation. The crystalline phase, microstructure, dielectric and electrical properties of films were investigated as a function of the (Ti＋Sn)/Ba ratio. When $BaTiO_3$ sources doped with $20{\sim}50\;mol%$ of Sn were evaporated, $BaSnO_3$films were grown due to the higher vapor pressure of Ba and Sn than of Ti. However, it was possible to grow the $Ba(Ti,Sn)O_3$ thin films with {\leq}\;15\;mol%$ of Sn by co-evaporation of BTS and Ti metal sources. The (Ti＋Sn)/Ba and Sn/Ti ratio affected the microstructure and surface roughness of films and the dielectric constant increased with increasing Sn content. The dielectric constant and dissipation factor of $Ba(Ti,Sn)O_3$ thin films with {\leq}\;15\;mol%$ of Sn showed the range of 120 to 160 and $2.5{\sim}5.5%$ at 1 KHz, respectively. The leakage current density of films was order of the $10^{-9}{\sim}10^{-8}A/cm^2$ at 300 KV/cm. The research results showed that it was feasible to grow the $Ba(Ti,Sn)O_3$ thin films as dielectrics for MLCCs by an e-beam evaporation technique.

• Composites Research
• /
• v.30 no.3
• /
• pp.202-208
• /
• 2017

Resin transfer molding (RTM) is a mass production process that allows the fabrication of composites ranging in size from small to large. Recently, fast curing resins with a curing time of less than about 10 minutes have been used in the automotive and aerospace industries. The viscosity of resin is bound up with the degree of cure, and it can be changed rapidly in the fast-cure resin system during the mold filling process. Therefore, it is advantageous to experimentally measure and evaluate the degree of cure because it requires much effort to predict the flow characteristics and cure of the fast curing resin. DMA and dielectric technique are the typical methods to measure the degree of cure of composite materials. In this paper, the resin flow and degree of cure were measured through the multi-channel dielectric system. A total of 8 channels of dielectric sensors were used and resin flow and degree of cure were measured and compared with each other under various pressure conditions.

• Applied Science and Convergence Technology
• /
• v.25 no.5
• /
• pp.88-91
• /
• 2016

The $Pb[(Mg_{1/3}Ta_{2/3})_{0.7}Ti_{0.3}]O_3$+xwt%PbO systems at temperature of $1250^{\circ}C$ for 4 hours was successful synthesized. In this study, PbO-doped $Pb[(Mg_{1/3}Ta_{2/3})_{0.7}Ti_{0.3}]O_3$ systems with non-linear behaviors showed ordering-degree dependence at the low temperature range were prepared using the columbite precursor method. And the characteristic of remnant polarization vs. electric field were analyzed. The pyroelectric, dielectric and piezoelectric properties of partially disordered $Pb[(Mg_{1/3}Ta_{2/3})_{0.7}Ti_{0.3}]O_3$+xwt%PbO solid solutions were studied as a function of temperature, frequency, and electric field. It showed distinct features of temperature dependent of pyroelectric coefficient, spontaneous polarization and dielectric constant at about $50^{\circ}C$. The figure of merit was calculated as pyroelectric coefficient, dielectric constant and dissipation factor. It was found that the high voltage responsivity FV, high detectivity FD were $0.0373m^2/C$ and $0.6735{\times}10^{-4}Pa{-1/2}$, respectively, in the $Pb[(Mg_{1/3}Ta_{2/3})_{0.7}Ti_{0.3}]O_3$+3.0 wt%PbO system.

• Electrical & Electronic Materials
• /
• v.9 no.2
• /
• pp.146-151
• /
• 1996

PZT powders were prepared by the molten salt synthesis method. The porous PZT ceramics were made from a mixture of PZT and polyvinylalcohol(PVA) by BURPS(Bumout Plastic Sphere) technique. The 3-3 type composites were fabricated by impregnating an sintered porous PZT ceramics with various polymer matrices. The relative permittivity of 3-3 type composite specimens was shown 860-1,100 smaller than that of solid PZT ceramics(2,100), and the dissipation factors of composite specimens were about 0.02 to 0.03. The piezoelectric coefficient d$_{33}$ of composite specimens(285-328*10$^{12}$ C/N) was comparable with that of single phase PZT specimens(364*10$^{-12}$ C/N). The thickness mode coupling factor k$_{t}$(O.5-0.6) of composite specimens was comparable with that of single phase PZT specimens(k$_{t}$-0.7), and the mechanical quality factor of composite specimens was smaller than 10, and thus these 3-3 type composite specimens would be believed as a good candidates for broad band transducer applications.ons.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.1
• /
• pp.8-13
• /
• 1990

The microscopic relaxation parameters for the single crystal were measured by using thermally stimulated depolarization (TSD). Initial rise method, various heating rate method and total glow peak method were used for the determination of the activation energy and Debye relaxation time from TSD glow curves. Activation energy, pre-exponential factor and relaxation time for impurity-vacancy dipole reorientation were 0.55eV, 1.97$\times$10 super(-12) sec and 12.19sec in average, respectively. Dielectric dissipation factor for the crystal was calculated from the measured TSD glow curve, its value being about 3$\times$10 super(-2).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.94-98
• /
• 2000

Polycrystalline SBTN ferroelectric thin films were prepared by sol-gel method with various Nb mole ratios on Pt/ $SiO_2$/Si (100) substrates. The films were annealed at different temperatures and characterized in terms of phase and microstructure. Relatively a well saturated hysteresis pattern was obtained at x =0.2 in S $r_{0.8}$B $i_{2.3}$(T $a_{1-x}$ N $b_{x}$)$_2$ $O_{9+}$$\alpha$/ thin films. At an applied voltage of 5V, the dielectric constant ($\varepsilon$$_{r}$) and dissipation factor (tan $\delta$) of typical S $r_{0.8}$B $i_{2.3}$(T $a_{1-x}$ N $b_{x}$)$_2$ $O_{9+}$$\alpha$/ thin film (x=0.2) were about 236.2 and 0.034. Measured remanent polarization (2Pr) and coercive field (Ec) were 4.28C/c $m_2$, and 38.88kv/cm respectively. No fatigue was observed up to 6$\times$10$_{10}$ switching cycles at 5V and the normalized polarization reduced by a factor of only 4%.%. 4%.%. 4%.%.%.%.%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.5
• /
• pp.301-313
• /
• 2021

Theoretical background for the meaning of various piezoelectric properties can be easily found in a number of textbooks and academic papers. In contrast, how they are actually measured and characterized are rarely described, though this information would be the most important especially to the researchers who just started working on the field. It follows that this report was intended to provide a practical guidance for measuring basic but essential properties of ferroelectric-based piezoelectric materials. The discussion begins with how to measurement dielectric properties such as dielectric permittivity and loss (dissipation factor), followed by piezoelectric properties such as piezoelectric constants, electromechanical coupling factor, and quality factor as well as ferroelectric features, i.e., electric field dependent polarization hysteresis. Though our discussion here is limited to the techniques that are already well-standardized, it is expected to make a seed to be developed into more challenging and creative ones.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.99-99
• /
• 2009

Two different micro-flows during the evaporation of ink droplets were achieved by engineering both surface tension gradient and compositional gradient across the ink droplet: (1) Coffee-ring generating flow resulting from the outward flow inside the ink droplet & (2) Marangoni flow leading to the circulation flow inside the ink droplet. The surface tension gradient and the compositional gradient in the ink droplets were tailored by mixing two different solvents with difference surface tension and boiling point. In order to create the coffee-ring generating flow (outward flow), a single-solvent system using N,N-dimethylformamide with nano-sized spherical alumina particles was formulated, Marangoni flow (circulation flow) was created in the ink droplets by combining N,N-dimethylformamide and fotmamide with the spherical alumina powders as a co-solvent ink system. We have investigated the effect of these two different flows on the formation of ceramic films by inkjet printing method, The packing density of the ceramic films printed with two different ink systems (single- and co-solvent systems) and their surface roughness were characterized. The dielectric properties of these inkjet-printed ceramic films such as dielectric constant and dissipation factor were also studied in order to evaluate the feasibility of their application to the electronic ceramic package substrate.