PURPOSE. This study evaluated the shear bond strength between 3D printed provisional resin and conventional provisional resin depending on type of conventional provisional resin and different surface treatments of 3D printed resin. MATERIALS AND METHODS. Ninety-six disc-shaped specimens (Ø14 mm × 20 mm thickness) were printed with resin for 3D printing (Nextdent C&B, Vertex-Dental B. V., Soesterberg, Netherlands). After post-processing, the specimens were randomly divided into 8 groups (n=12) according to two types of conventional repair resin (methylmethacrylate and bis-acryl composite) and four different surface treatments: no additional treatment, air abrasion, soaking in methylmethacrylate (MMA) monomer, and soaking in MMA monomer after air abrasion. After surface treatment, each repair resin was bonded in cylindrical shape using a silicone mold. Specimens were stored in 37℃ distilled water for 24 hours. The shear bond strength was measured using a universal testing machine at a crosshead speed of 0.5 mm/min. Failure modes were analyzed by scanning electron microscope. Statistical analysis was done using one-way ANOVA test and Kruskal-Wallis test (α=.05). RESULTS. The group repaired with bis-acryl composite without additional surface treatment showed the highest mean shear bond strength. It was significantly higher than all four groups repaired with methylmethacrylate (P<.05). Additional surface treatments, neither mechanical nor chemical, increased the shear bond strength within methylmethacrylate groups and bis-acryl composite groups (P>.05). Failure mode analysis showed that cohesive failure was most frequent in both methylmethacrylate and bis-acryl composite groups. CONCLUSION. Our results suggest that when repairing 3D printed provisional restoration with conventional provisional resin, repair with bis-acryl composite without additional surface treatment is recommended.
Objectives : This study investigated the hypothesis that the dentin bond strength of self-etching adhesives (SEAs) may be improved by applying a coat of hydrophobic, neutral adhesive resin in addition to SEA. Method and Materials : The bond strengths of two SEAs - Experimental SEA (EX) and Adper Prompt (AP) - were measured with three bonding protocols. The D/E resin of All-Bond 2 was applied as the hydrophobic, neutral adhesive. Clearfil SE Bond (SE, self-etching primer system) and All-Bond 2 (AB, total etching system) were used as references. The following protocols were used: (1) EX1 (EX 1 coat); (2) EX2 (EX 2 coats); (3) EX+ (EX 1 coat + D/E resin); (4) AP1 (AP 1 coat); (5) AP2 (AP 2 coats); (6) AP+ (AP 1 coat + D/E resin); (7) SE (SE primer + SE bond); (8) SE+ (SE primer + D/E resin); (9) AB (etching + AB primer + D/E resin). Filtek Z250 composite resin was built up and the microtensile bond strength (MTBS) values of the specimens were compared. The fractured surfaces were observed using SEM. Results : When SEA was used as self-etching primer and hydrophobic, neutral adhesive was applied as well, MTBS was significantly higher than that when either one coat or two coats of SEA only were used (p < 0.05). Conclusion : The hydrophobic, neutral adhesive improved the integrity of the bonded interface obtained with SEA.
치과용 가시광선 중합형 복합수지의 광중합효율을 높이기 위해 2종의 새로운 액체형 amine 개시제인 MA, MPT와 현재 가장 많이 사용되고 있는 개시제인 AEM을 CQ, PD, DA에 각각 첨가하고 UDMA의 광중합효율을 알아본 결과 다음과 같은 결론을 얻었다. 1. 조사시간이 증가됨에 따라 amine 개시제의 종류에 관계없이 광중합효율이 점차 증가되었으며, 약 60초까지 조사였을 때에는 광중합효율이 급격히 증가되었으나 그 이상 조사하여도 광중합효율이 크게 증가되지 않았다. 2. AEM, MA와 MPT를 사용하였을 경우 모두 CQ > PD > DA의 순으로 광중합효율이 우수하게 나타났으나 AEM을 사용하였을 때 PD와 CQ는 큰 차이를 보이지 않았다. 3. CQ의 광중합효율은 새로운 광개시제인 MA와 MPT를 사용하였을 때가 범용으로 사용되고 있는 amine 개시제인 AEM을 사용하였을 경우보다 중합효율이 증가하는 결과를 보였다. 4. PD의 광중합효율은 MA와 함께 사용하였을 경우가 가장 높게 나타났으나 AEM의 경우와 큰 차이를 보이지는 않았다. 5. 이상의 결과로부터 MA와 CQ 및 PD를 함께 사용한 새로운 광중합시스템이 광중합효율을 높이는데 효율적인 것을 알 수 있었다.
본 논문은 monomer에서 결합증진에 많은 역할을 하는 MMA와 TEGDMA의 농도별 표면 처리와 silane coupling agent로 표면 처리한 것이 의치상 레진과 이장재간의 결합력에 미치는 영향에 대해 알아보고자 하였다. 의치상 레진에 MMA와 TEGDMA의 농도별 표면 처리와 silane coupling agent로 표면처리 후 이장재를 주입하여 전단결합강도를 측정하였다. MMA와 TEGDMA의 농도별 표면 처리에 따른 의치상 레진과 이장재간의 전단결합강도에서는 Vertex self curing resin에서 95%, 90%, 80%, Kooliner에서는 95%, 90%에서 유의적으로 높게 나타났다(P<0.05). 또한, silane coupling agent 5%로 표면 처리한 그룹이 Vertex self curing resin과 Kooliner 모두에서 전단결합강도가 유의적으로 높게 나타났다(P<0.05). 따라서 적절한 화학적 표면 처리는 의치상 레진과 이장재간의 결합력 증가에 영향을 미치리라 사료된다.
시판 중인 어린이 음료가 레진계 치면열구전색제에 미치는 물리 화학적 영향을 알아보기 위해 판매량이 높은 3종의 어린이 음료와 대조군으로 생수를 선정하였다. 제조사의 지시에 따라 레진 시편을 제작하여 시편의 초기 거칠기 값(Ra)를 측정하였고, 각 음료의 pH를 측정한 후, 레진 시편을 각각의 음료에 침지시켜 $37^{\circ}C$ 배양기에서 72시간 보관하였다. 72시간 후 레진 시편의 표면 거칠기를 측정하였고 시편 표면의 형태변화 관찰을 위해 주사전자현미경으로 관찰하였다. 레진 시편에서 용출된 단량체의 종류 및 용출량은 HPLC를 이용하여 비교 분석하였다. 생수를 제외한 모든 실험음료에 구연산이 첨가되어 있었고 어린이 음료의 평균 pH는 $3.25{\pm}0.17$로 '아이키커'에서 $3.03{\pm}0.01$로 가장 낮았고 '뽀로로'에서 $3.47{\pm}0.02$로 가장 높았다. 어린이 음료에 침지 후 시간 경과에 따른 표면 거칠기가 증가하였고 레진 시편의 표면에 기질의 탈락을 관찰하였다. 모든 실험음료에서 bis-GMA는 유출되지 않았으나 생수를 제외한 어린이 음료에서는 TEGDMA가 유출되었다. 이상의 결과 어린이 음료는 치면열구전색제의 열화와 단량체의 유리를 촉진할 수 있으며 유리된 단량체는 성장 중인 어린이에게 더 큰 영향을 미칠 수 있으므로 어린이 음료를 빈번히 음용하는 것은 주의가 필요하다.
Purpose: In order to find out the impact of changes in polymerization conditions of orthodontic acrylic resin on maximum load. Methods: While maintaining mixing ratio 3:1 of polymer and monomer in spray-on way in the production condition of polymerization temperature $25^{\circ}C$ or $37^{\circ}C$ for 10 minutes or 30 minutes of polymerization time by pressure $3kfg/cm^2$ or $6kfg/cm^2$ in the lab maintaining $25^{\circ}C$ of room temperature, the change in maximum load rise rate was tested by producing 5 acrylic resin specimens for orthodontics per group to meet the standards of $25mm{\times}2mm{\times}2mm$ and using INSTRON with the 3rd bar 2mm in diameter and parallel support bending device of $15{\pm}0.1mm$ as test equipment showing 30.00mm/min of crosshead speed, $50{\pm}16$ N/min of load ratio in the laboratory of $24^{\circ}C$ room temperature and as a result, the following results were obtained. Results: 1. When increasing pressure from $3kfg/cm^2$ to $6kfg/cm^2$, maximum load was lowered by -4.285%. 2. When increasing polymerization time from 10 minutes to 30 minutes, maximum load rose by 3.848%. 3. When increasing polymerization temperature from $27^{\circ}C$ to $37^{\circ}C$, maximum load rose by 5.854%. Conclusion: Considering the above test results that polymerization time and polymerization temperature when polymerizing acrylic resin for orthodontics according to changes in working conditions had an impact on the rate of rise of maximum load values but the rate of rise was lowered when increasing pressure from $3kfg/cm^2$ to $6kfg/cm^2$, we came to a conclusion that high pressure more than necessary does not affect the rate of rise of maximum load.
본 연구는 물성의 단점이 많은 희석재인 TEGDMA의 사용을 줄이기 위해, Bis-GMA의 유도체로서 중합수축이 적고 점도가 낮은 새로운 단량체인 methoxlyated Bis-GMA (Bis-M-GMA)를 첨가한 복합레진의 법랑질과 상아질 변연에서의 미세누출을 비교하였다. 40개의 발거된 상하악 소구치의 협면과 설면에 $2\;mm\;{\times}\;2\;mm\;{\times}\;2\;mm$ 와동을 형성하여 4개 군으로 분류하였다. Clearfil SE bond와 복합레진을 이용하여 와동을 수복하였다. EX1군은 실험용 복합레진 1 (Bis-M-GMA/TEGDMA = 95/5wt% ,40 nm 나노필러 함유), EX2군은 실험용 복합레진 2 (Bis-M-GMA/TEGDMA = 95/5wt%, 20 nm 나노필러 함유), EX3군은 실험용 복합레진 3 (Bis-GMA/TEGDMA = 70/30wt%, 40 nm 나노필러 함유), Z250군은 Filtek 2250으로 각각 와동을 수복하였다. 모든 시편은 실온의 실온의 생리식염수에서 7일간 보관한 후, $5^{\circ}C$와 $55^{\circ}C$ 의 수조에서 500회의 열순환을 실시하고, 2% methylene blue염색 용액에 24시간 담근 후, 협설측으로 치아 장축에 평행하게 절단하고 광학입체현미경하에서 각 수복물의 법랑질과 상아질 변연부의 색소침투 정도를 관찰하여 미세누출점수로 기록한 후 각 군의 유의성을 검증하였다. 법랑질 변연이 상아질 변연보다 유의성있게 낮은 미세변연누출을 보였다 (p = 0.007). 각 변연에서 EX1, EX2보다 EX3, Z250군의 염색침투도가 증가하는 경향을 보였지만 통계적으로 유의성 있는 차이를 보이지는 않았다 (p > 0.05). 점도가 낮은 새로운 레진단량체인 Bis-M-GMA는 기존의 단량체인 Bis-GMA의 대체재로 고려될 수 있다.
The auther measured exothermic tempreature of the 5 kinds of direct resins during polymerization. Direct resins were mixed into the rubber cup(550-600㎣ in volume) with grass rod at room temperature (23.6℃) for 30 seconds and thermometer was placed approximately at the geometric center of the resin mass in the rubber cup. Polymer-monomer ratio was determined by instruction of the packages. The results were as follows.
1) The heat generated during polymerization was under 47.3℃.
2) The time at which the highest temperature is reached during polymerization was within 20.5 minutes.
3) Slow curing resins produced lower heat than quick curing resins and quick curing resins presented higher temperature than slow curing resins.
4) The highest temperature was sustained momentarily.
치과용 복합레진은 bis GMA형의 monomer가 개발되고, 무기 filler가 첨가되어 물리적인 성질이 더욱 향상되었으며, 또한 법랑질에 대한 산부식법을 통하여 치아에 대한 결합력을 높을 수 있는 방법이 도입되면서 치과용 수복물로서 각광을 받아 왔다. 특히 복합레진은 이전까지 이용되었던 silicate cement 이나 acrylic resin에 비하여 변색이 적고, 원래의 형태를 비교적 잘 유지하는 장점을 가져서 전치부의 수복에 유용한 재료로 인식되었다. 복합레진을 이용한 전치부의 수복은 비교적 적은 치질의 삭제만으로도 가능하고, 심미적으로도 우수한 결과를 보이고 있어서 올바른 술식을 통하여 적절히 이용한다면 좋은 임상적인 결과를 얻을 수 있는 것이 사실이지만 재료학적인 한계가 아직 까지는 엄연히 존재한다. 복합레진을 이용한 전치부의 수복에 있어서, 복합레진의 문제점과 이를 줄이기 위한 방법, 임상시의 주의점 등에 관해 살펴보도록 한다.
가철성 상교정 장치에 많이 사용되는 자가중합형 상교정용 레진의 미반응 단량체는 레진의 물성과 생물학적인 면에 많은 영향을 끼친다. 따라서 미반응 단량체를 최소화하고 중합률을 최대로 하는 중합방법에 대한 연구는 중요한 의의를 갖는다. 저자는 자가중합형 상교정용 레진의 중합시간과 중합방법에 따른 중합률을 비교해보기 위해 시편을 다음과 같이 5군으로 나누어 연구를 진행하였다. 상교정용 레진의 분말과 용액을 혼합하여 제 1군은 $28^{\circ}C$의 공기중에 보관하였고, 제 2군은 $28^{\circ}C$의 물에, 제 3군은 $28^{\circ}C$의 물과 30psi의 압력에, 제 4군은 $43^{\circ}C$의 물에, 제 5군은 $43^{\circ}C$의 물과 30psi의 압력하에 각각 보관하였고, 10분, 1시간, 12시간, 1일, 3일 경과 후에 각 시편을 Fourier 변환적외선분광법을 이용하여 중합률을 측정하여 다음과 같은 결론을 얻었다. 1. 모든 군에서 중합시간이 경과함에 따라 중합률도 지속적으로 증가하는 양상을 보였다. 10분 경과 후의 결과와 비교하여 볼 때, 제 1군은 12시간 경과 후부터 중합률의 증가가 유의성이 있었고, 제 2군과 3군, 4군, 5군은 1시간 경과 후부터 유의성이 있었다(p<0.05). 2. 10분과 1일, 3일 경과 후에 제 5군, 제 4군, 제 3군, 제 2군, 제 1군의 순서대로 중합률이 높았다. 3. 중합시 온도에 따른 비교에서, 1일 경과 후를 제외하고는 모든 시간에서 $43^{\circ}C$에서 중합시킨 군의 중합률이 $28^{\circ}C$에서 중합시킨 군의 중합률 보다 유의성 있게 높았다(p<0.05). 4. 압력은 12시간 경과 후를(p<0.05) 제외하고는 중합률에 영향을 주지 못했다. 5. 보관방법은 1시간 경과 후를(p<0.05) 제외하고는 중합률에 영향을 주지 못했다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.