• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1491-1495
• /
• 2004

In this paper, resonant ultrasound spectroscopy(RUS) was used to determine the natural frequency of a spherical and a aspherical lens. The objective of the paper is to evaluate defect and shape error by using nondestructive evaluation method with Resonant Ultrasound Spectroscopy(RUS). The principle of RUS is that the mechanical resonant frequency of the materials depends on density, and the coefficient of elasticity. We evaluated existence of flaws through comparison with resonant frequency of a spherical and a aspherical lens. The spherical glass lenses were made of BK-7 glass, one's diameter in 2mm and 5mm. The polished spherical glass lenses had no deflection or a deflection below 2.0${\mu}{\textrm}{m}$. Also, The aspherical lens were made of same material and ones diameter in 7mm and thickness in 3.4mm. In the experiment, we were performed to investigate relationship between frequency measuring parameter($\beta$) and mass of each specimens. The difference between resonant frequency and mode of aspherical glass lens which has no defect was distinguished from aspherical glass lens which has some defects.

• Journal of Chest Surgery
• /
• v.17 no.4
• /
• pp.729-734
• /
• 1984

Bochdalek hernia is a type of congenital diaphragmatic defect in the posterolateral portion of the diaphragm. The defect is usually Lt. sided due to protective effect of liver on right. Sex distribution is male preponderance [2:1] and it is diagnosed during neonate, mostly first 24 hours, due to severe respiratory distress. We experienced a rare case of old aged female patient with congenital Bochdalek hernia on Rt. side which was found incidentally during treatment of spontaneous pneumothorax of Rt. side. 17 year old female patient was admitted to CS department for chest discomfort on right and mild dyspnea with duration of 20 days. Under the diagnosis of spontaneous pneumothorax, Rt. closed thoracostomy and underwater sealed drainage with continuous suction was applied. On follow-up chest x-ray, poorly defined hazy increased density with multiple air-fluid levels in Rt. lower lung field and Lt. subphrenic free air were noted. So, Barium enema was done under the impression of Rt. diaphragmatic hernia, and nearly entire colon proximal to sigmoid was demonstrated in the Rt. hemithorax. Operation was done-for surgical repair of defected diaphragm through Rt. posterolateral thoracotomy. Operative findings were as follows; 1.Hypoplastic Rt. lung, esp. RML & RLL. 2.Nearly entirely intestines were herniated. 3.Diaphragmatic defect was located on posterolateral portion of the diaphragm, about 10x3cm in size with blunt smooth margin. 4.A large bleb on apex of RUL of lung. Herniated intestines were repaired into abdominal cavity manually and defect of diaphragm was repaired with No. I black silk interrupted sutures directly, and bleb was resected. Postoperative courses were uneventful and the patient was discharged with good condition on POD 14th.

• Imaging Science in Dentistry
• /
• v.46 no.1
• /
• pp.39-45
• /
• 2016

The incidental finding of an enlarged mastoid foramen on the right posterior mastoid region of temporal bone is reported, together with a discussion of its clinical significance. A 67-year-old female underwent the pre-implant assessment of a maxillary left edentulous region. A cone-beam computed tomographic (CBCT) image was acquired and referred for consultation. Axial CBCT slices revealed a unilateral, well-defined, noncorticated, low-attenuation, transosseous defect posterior to the mastoid air cells in the right temporal bone. The borders of the osseous defect were smooth and continuous. No other radiographic signs suggestive of erosion or sclerosis were noted in the vicinity. The density within the defect was homogenous and consistent with a foramen and/or soft tissue. The patient's history and physical examination revealed no significant medical issues, and she was referred to a neuroradiologist for a second opinion. The diagnosis of an enlarged mastoid foramen was made and the patient was reassured.

• Nuclear Engineering and Technology
• /
• v.55 no.1
• /
• pp.209-214
• /
• 2023

The effect of thermal annealing on defect recovery of in-core neutron-irradiated 4H-SiC was investigated. Au/SiC Schottky diodes were manufactured using a 4H-SiC epitaxial wafer that was neutron-irradiated at the HANARO research reactor. The electrical characteristics of their epitaxial layers were analyzed under various conditions, including different neutron fluences (1.3 × 10¹⁷ and 2.7 × 10¹⁷ neutrons/cm²) and annealing times (up to 2 h at 1700 ℃). Capacity-voltage measurements showed high carrier compensation in the neutron-irradiated samples and a recovery tendency that increased with annealing time. The carrier density could be recovered up to 77% of the bare sample. Deep-level-transient spectroscopy revealed intrinsic defects of 4H-SiC with energy levels 0.47 and 0.68 eV below the conduction-band edge, which were significantly increased by in-core neutron irradiation. A previously unknown defect with a high electron-capture cross-section was discovered at 0.36 eV below the conduction-band edge. All defect concentrations decreased with 1700 ℃ annealing; the decrease was faster when the defect level was shallow.

• Journal of the Korean Ceramic Society
• /
• v.36 no.9
• /
• pp.954-964
• /
• 1999

The effect of fabrication variables and microstructures on the compressive strength of open cell alumina zirconia and silicon nitride ceramics fabricated by polymeric sponge method was investigated. Bulk density and compressive strength of open cell ceramics were mainly affected by coating characteristics of ceramic slurry on polymeric sponge that controlled a shape thickness and defect of the struts. Sintering temperature was optimized for enhancement of strut strength and compressive strength of open cell ceramics. Relative density and compressive strength behaviors were relatively well matched with the predicted values. Open cell ceramics of lower relative density below 0.1 prepared by first relatively well matched with the predicted values. Open cell ceramics of lower relative density below 0.1 prepared by first coating of ceramic slurry had thin triangular prismatic struts that were often broken or longitudinally cracked. With an application of second coating of slurry shape of struts was transformed into thickner cylindrical one and defects in struts were healed but the relative density increased over 0.2 Open cell zirconia had both the highest bulk density and compressive strength and alumina had the lowest compressive strength while silicon nitrides showed relatively high compressive strength and the lowest density. Based upon the analysis open cell silicon nitride was expected to be one of potential structural ceramics with light weight.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.45 no.2
• /
• pp.97-107
• /
• 2019

Objectives: Small animal maxillofacial models, such as non-segmental critical size defects (CSDs) in the rabbit mandible, need to be standardized for use as preclinical models of bone regeneration to mimic clinical conditions such as maxillofacial trauma. The objective of this study is the establishment of a mechanically competent CSD model in the rabbit mandible to allow standardized evaluation of bone regeneration therapies. Materials and Methods: Three sizes of bony defect were generated in the mandibular body of rabbit hemi-mandibles: $12mm{\times}5mm$, $12mm{\times}8mm$, and $15mm{\times}10mm$. The hemi-mandibles were tested to failure in 3-point flexure. The $12mm{\times}5mm$ defect was then chosen for the defect size created in the mandibles of 26 rabbits with or without cautery of the defect margins and bone regeneration was assessed after 6 and 12 weeks. Regenerated bone density and volume were evaluated using radiography, micro-computed tomography, and histology. Results: Flexural strength of the $12mm{\times}5mm$ defect was similar to its contralateral; whereas the $12mm{\times}8mm$ and $15mm{\times}10mm$ groups carried significantly less load than their respective contralaterals (P<0.05). This demonstrated that the $12mm{\times}5mm$ defect did not significantly compromise mandibular mechanical integrity. Significantly less (P<0.05) bone was regenerated at 6 weeks in cauterized defect margins compared to controls without cautery. After 12 weeks, the bone volume of the group with cautery increased to that of the control without cautery after 6 weeks. Conclusion: An empty defect size of $12mm{\times}5mm$ in the rabbit mandibular model maintains sufficient mechanical stability to not require additional stabilization. However, this defect size allows for bone regeneration across the defect. Cautery of the defect only delays regeneration by 6 weeks suggesting that the performance of bone graft materials in mandibular defects of this size should be considered with caution.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.29-35
• /
• 1998

Substrates, SiC raw materials and graphite crucibles were purified for growing the high quality 6H-SiC single crystal ingot. Especially, XRD data of raw materials were analyzed before and after purification. We have grown 6H-SiC single crystal ingot up to 33 mm in diameter and 11 mm in length and SiC wafer for using the substrate and observing the internal defects was about 33 mm in diameter and 0.5 mm in thickness. Utilizing optical microscpe and Raman spectroscopy, internal defects density and crystallinity of the SiC wafer obtained by purification processes before crystal growth were measured. As a result, micropipe density and planar defect density were 100/$\textrm{cm}^2$ and 30/$\textrm{cm}^2$ respectively. Therefore, high quality 6H-SiC single crystal could be grown because internal defects density of 6H-SiC single crystal ingot was decreased by the purification processes before crystal growth.

• Journal of Korea Multimedia Society
• /
• v.7 no.4
• /
• pp.451-458
• /
• 2004

A leather quality inspection by naked eyes has known as unreliable because of its biological characteristics like accumulated fatigue caused from an optical illusion and biological phenomenon. Therefore it is necessary to automate the leather quality inspection by computer vision technique. In this paper, we present automatic leather qua1ity classification system get information from leather surface. Leather is usually graded by its information such as texture density, types and distribution of defects. The presented algorithm explain how we analyze leather information like texture density and defects from the gray-level images obtained by digital camera. The density data is computed by its ratio of distribution area, width, and height of Fourier spectrum magnitude. And the defect information of leather surface can be obtained by histogram distribution of pixels which is Windowed from preprocessed images. The information for entire leather could be a standard for grading leather quality. The proposed leather inspection system using machine vision can also be applied to another field to substitute human eye inspection.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.10a
• /
• pp.363-366
• /
• 2001

The present process of grading leather quality by the rare eyes is not reliable. Because inconsistency of grading due to eyes strain for long time can cause incorrect result of grading. Therefore it is necessary to automate the process of grading quality of leather based on objective standard for it. In this paper, leather automatic classification system consists of the process obtaining the information of leather and the process grading the quality of leather from the information. Leather is graded by its information such as texture density, types and distribution of defects. This paper proposes the algorithm which sorts out leather information like texture density and defects from the gray-level images obtained by digital camera. The density information is sorted out by the distribution value of Fourier spectrum which comes out after original image is converted to the image in frequency domain. And the defect information is obtained by the statistics of pixels which is relevant to Window using searching Window after sort out boundary lines from preprocessed images. The information for entire leather is used as standard of grading leather quality, and the proposed algorithm is practically applied to machine vision system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1997.02a
• /
• pp.47-48
• /
• 1997