• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.2
• /
• pp.191-197
• /
• 2015

The message passing interface (MPI) and hybrid programming models for the parallel computation of a pressure equation were compared in a distributed memory system. Both models were based on domain decomposition, and two numbers of the sub-domain were selected by considering the efficiency of the hybrid model. The parallel performances for various problem sizes were measured using up to 96 threads. It was found that in addition to the cache-memory size, the overhead of the MPI communication/OpenMP directives affected the parallel performance. For small problems, the parallel performance was low because the percentage of the overhead of the MPI communication/OpenMP directives increased as the number of threads increased, and MPI was better than the hybrid model because it had a smaller communication overhead. For large problems, the parallel performance was high because, in addition to the cache effect, the percentage of the communication overhead was relatively low compared to that for small problems, and the hybrid model was better than MPI because the communication overhead of MPI was more dominant than that of the OpenMP directives in the hybrid model.

• Journal of the Korean Institute of Gas
• /
• v.21 no.6
• /
• pp.52-60
• /
• 2017

In diffusion process exhaust line during semiconductor manufacturing process, In order to improve the transportation efficiency in the piping by removing "The reaction by-product, $ZrO_2$ and The unreacted material, TEMAZ, TMA, $O_3$, etc" and "Powder being deposited", the piping temperature was raised to $80^{\circ}C$ or more by using the heater jacket, and the bellows at the rear end of the vacuum pump ruptured. So conducted a case study and try to prevent the similar accidents from occurring through case studies. The causes of the accident were analyzed as follows: the inflow of outside air due to the generation of a gap on the suction side of the vacuum pump and heating the pipe with the heater jacket resulted in the overpressure in the pipe due to the volumetric expansion of the gas generated by decomposition of the unreacted TEMAZ, It can be assumed that the most vulnerable bellows of the piping has been ruptured. In order to prevent such accidents, This study is aimed to identify the cause of pipeline rupture accident and to establish safety measures for the prevention of similar accidents by evaluating physical hazards of TEMAZ, which is assumed to be the cause of pipe rupture accident.

• Journal of the Korean Chemical Society
• /
• v.10 no.1
• /
• pp.32-42
• /
• 1966

The electrolysis of tungstic oxide dissolved in the bath of calcium chloride and calcium oxide was studied to produce metallic tungsten using carbon as anode and iron as cathode in the temperature range of 900^{\circ}$ to $1200^{\circ}C$. The binary phase diagrams $CaCl_2$-CaO and $CaCl_2-CaWO_4$ systems were constructed to determine the suitability of bath composition and the range of temperatures for the electrolysis. As $WO_3$ reacted with $CaCl_2$ to form oxychloride in the fused salt, the addition of the proper amount of CaO was necessary to avoid the loss of $WO_3$. The optimum compositions of fused bath were $CaCl_2$ 100 parts, CaO and $WO_3$ each 10 to 20 parts, with the CaO, $WO_3$ ratio greater than unity, to keep freezing point low and to prevent the vaporization of $CaCl_2$. The observed decomposition voltage at which $WO_3$ decomposes to W and CO was-0.1 volt, whereas the calculated was -0.3 volt. Metallic tungsten deposited at the cathode reacted easily with CO formed secondarily at the anode surface, to form WC below $1050^{\circ}C$, so that the cell temperature should be above $1050^{\circ}C$. The effects of cathode current densities on current efficiency were minor in the range of 1 to 5 $amp/cm^2$.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.25 no.1
• /
• pp.35-45
• /
• 2017

In order to improve the anaerobic digestion efficiency of the sewage sludge, the methane potential of the hydrolysate generated from the hydro-thermal reaction at 170, 180, 190, 200, 210, $220^{\circ}C$ was analyzed and the constitutional characteristics of the organic materials were estimated by dividing organic materials of hydro-thermal hydrolysate into easily biodegradable, decomposition resistant, and non-biodegradable organic materials applying the parallel first order kinetics model. The ultimate methane potential of sewage sludge hydro-thermal hydrolysate increased to 0.39, 0.39, 0.40, 0.44, 0.45, and $0.46Nm^3/kg-VS_{added}$ as hydro-thermal reaction temperature increased from 170, 180, 190, 200, 210, $220^{\circ}C$. It has been shown that the organic matter of sewage sludge is solubilized to increase the content of biodegradable organic material($VS_B$). The easily degradable organic matter($VS_e$) content was highest at hydro-thermal reaction temperature of 200 and $210^{\circ}C$, and optimum hydro-thermal reaction temperature for organic matter solubilization of sewage sludge was in the range of $200{\sim}210^{\circ}C$. In addition, the amount of biodegradable organic material($VS_B$) and easily biodegradable organic matter ($VS_e$) in the hydrolysate of sewage sludge was the highest at hydro-thermal reaction temperature of $200^{\circ}C$.

• Korean Journal of Medicinal Crop Science
• /
• v.22 no.3
• /
• pp.231-236
• /
• 2014

This experiment was carried out to establish the optimum cutting time, plant growth regulator, and bed-soil for rooting by greenwood cutting of Schisandra chinensis. Approximately 7 cm long-shoots of greenwood cuttings were transplanted by various cutting times, plant growth regulators, and bed-soils in the plastic-film house. The rooting rate of greenwood cutting was 12.5% in the April 5th, 73.5% in the May 8th, and 75.5% in the August 5th. The number and length of primary root in greenwood cutting were more in the early May than those in the early August. For mass propagation of Schisandra chinensis. using greenwood cutting, shoots were treated with plant growth regulators on May to increase rooting rate. Rooting rate was 100% with IAA $50mg/{\ell}$, 92.9% with NAA $100mg/{\ell}$, and NAA $1,000mg/{\ell}$, for 60 min. To select effective media for rooting, various medias for bed-soil were treated by single and mixture form for 100 days after cutting. Rooting rate was 91.8% in the single treatment of peat moss or decomposition of granite soil, and this result was better than those in other treatment. The treatment by 1 : 1 mixture of peat moss and horticulture bed soil was rooting with 94.0% best rooting rate.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.8
• /
• pp.492-497
• /
• 2015

VOCs (Volatile Organic Compounds) are generally generated in the painting process, or at the company and laundry where use organic solvents. The VOCs consist of various hydrocarbons and has low calorific value due to its dilution with atmospheric air. Therefore, the VOCs are difficult to burn by a conventional fuel combustor. In this study, a novel plasma dump combustor was proposed for the treatment of low calorific VOC gases. This combustor was designed a combination of the characteristics in a plasma burner, a dump combustor and a 3D matrix burner. The combustor has good structure for maintaining enough residence time and reaction temperature for stable flame formation and VOC destruction. For investigating the performance characteristics of the plasma dump combustor, an experiment was achieved for VOC feed rate, VOC injector position, etc. Toluene was used as a surrogate of VOC. The novel combustor gave better performance than a conventional combustor, showing that VOC destruction rate and energy efficiency were 89.64% and 12.27 kg/kWh respectively, at feeding rate of 450 L/min of VOC of 3,000 ppm of toluene concentration.

• Geotechnical Engineering
• /
• v.14 no.4
• /
• pp.151-162
• /
• 1998

The compressibility and the permeability of organic soil are so high that they cause many engineering problems when constructing a structure on the soil. If the organic content of the soil could be reduced by any applicable engineering technique, the engineering properties of the soils can be improved to some extent. The purpose of this study would thus be focused on how to decrease the amount of organic matters by applying aerobic biodegradation for eliminating post-construction settlement problems. To enhance the aerobic decomposition, oxygen was supplied to the soil samples prepared by the mixture of kaolinite and sawdust as organic matter. The dissolved oxygen and the organic content of the soil samples were measured, in accordance with the passage of time through the bests. As oxygen suppliers, HaOa liquid and pure oxygen gas were compared to meet the requirement of the test purposes. Newly manufactured oedometer with the diameter of 130 mm and the height of 300 mm was used for 100 days to perform the compressibility tests for the soils. Based on the results of this experiment, the oxygen gas-treated samples with nutrient settled 30% more than the samples untreated. This confirmed the efficiency of the aerobic biodegradation. $NaNO_3$ added into the soils as nutrients was proved more effective than $K_2HP0_4$. To confirm the activity of micro-organisms, sodium azide was also added to the soils.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.29-34
• /
• 2019

Silicon carbide is considered to be a potentially useful material for high-temperature electronic devices, as its large energy band gap and the p-type and/or n-type conduction can be controlled by impurity doping. Particularly, electric conductivity of porous n-type SiC semiconductors fabricated from ${\beta}-SiC$ powder at $2000^{\circ}C$ in $N_2$ atmosphere was comparable to or even larger than the reported values of SiC single crystals in the temperature region of $800^{\circ}C$ to $1000^{\circ}C$, while thermal conductivity was kept as low as 1/10 to 1/30 of that for a dense SiC ceramics. In this work, for the purpose of decreasing sintering temperature, it was attempted to fabricate porous reaction-sintered bodies at low temperatures ($1400-1600^{\circ}C$) by thermal decomposition of polycarbosilane (PCS) impregnated in n-type ${\beta}-SiC$ powder. The repetition of the impregnation and sintering process ($N_2$ atmosphere, $1600^{\circ}C$, 3h) resulted in only a slight increase in the relative density but in a great improvement in the Seebeck coefficient and electrical conductivity. However the power factor which reflects the thermoelectric conversion efficiency of the present work is 1 to 2 orders of magnitude lower than that of the porous SiC semiconductors fabricated by conventional sintering at high temperature, it can be stated that thermoelectric properties of SiC semiconductors fabricated by the present reaction-sintering process could be further improved by precise control of microstructure and carrier density.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.10
• /
• pp.5-12
• /
• 2022

In this study, we investigated the UV/H₂O₂ process to treat organic compound-spilled water. In consideration of usage and properties, benzene, toluene, phenol, and methyl ethyl ketone were selected as representative organic compounds. The selected material was first removed by natural volatilization and aeration that simulated the pretreatment of the prcoess. After that, UV/H₂O₂ oxidation experiments were conducted under various H₂O₂ concentration conditions. Benzene and toluene were mostly volatilized before reaching the oxidation process due to high volatility. Considering the volatility, oxidation experiments were performed at an initial concentration of 5 mg/L for benzene and toluene. The UV/H₂O₂ oxidation process achieved 100% of benzene and toluene removal after 20 minutes under all hydrogen peroxide concentration conditions. The phenol was rarely removed from the volatile experiments and oxidation tests were performed at an initial concentration of 50 mg/L. The process showed 100 % phenol removal after 30 minutes under 0.12 v/v% of hydrogen peroxide concentration condition. Methyl ethyl ketone was removed 58 % after 2 hours of volatile experiments. The process showed 99.7% Methyl ethyl ketone removal after 40 minutes under 0.08 v/v% of hydrogen peroxide concentration condition. It was confirmed that the UV/H₂O₂ process showed high decomposition efficiency for the four selected organic compounds, and identified the amount of hydrogen peroxide in classified organic contaminants.

• Journal of the Korean GEO-environmental Society
• /
• v.25 no.5
• /
• pp.5-13
• /
• 2024

This paper investigates the stabilization feasibility of contaminated sediment contaminated with benzyl butyl phthalate (BBP) using acid/base-modified activated carbon. The efficiency of stabilizers was evaluated by analyzing the impact of the activated carbon on the decomposition and adsorption of the contaminant, along with the biological effects on earthworms. Additionally, the contaminant migration was monitored with the BBP concentration in pore water using low-density polyethylene. The research results indicated that the accumulated concentration of BBP was approximately 2% lower in the experimental group applying a 5% mixture ratio of modified activated carbon compared to the group applying a 10% mixture ratio. The leaching into water was reduced by over 18% in all experimental conditions after 7-day exposure period. Over 25% reduction was observed after 28-day exposure. The pore water concentrations were measured. After 7 days of exposure, the mechanically mixed experimental group exhibited a higher pore water stabilization rate compared to the biologically mixed group. Within the mechanically mixed group, the experimental group with 10% mixture of modified activated carbon showed a 1% higher stabilization rate than the group with 5% mixture. After 28 days of exposure, the biologically mixed experimental group demonstrated a higher pore water stabilization rate compared to the mechanically mixed group. Moreover, within the biologically mixed group, the experimental group with 10% mixture of modified activated carbon showed approximately 0.1% higher stabilization rate than the group with 5% mixture.