• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.354-354
• /
• 2007

Titanium nitride (TiN) thin films are widely used for hard coatings due to their superior hardness. In this paper, we wanted see how the films properties are changed according to DC power. TiN thin films were deposited by direct current (DC) magnetron sputtering method using TiN compound target on silicon substrates. The films structural properties are examined by X-ray Diffractions (XRD) and tribological properties are measured by nano-indentation, nano-scratch tester, nano-stress tester. Especially in DC power of 150 W, the maximum hardness and the minimum residual stress of TiN film exhibited about 25 GPa and 1 GPa, respectively. And also, the critical load of TiN film prepared by magnetron sputtering method were measured over 30 N.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.2
• /
• pp.23-27
• /
• 2000

Indium in oxide(ITO) films have been deposited on PET and glass substrates by DC reactive magnetron sputtering without post-deposition thermal treatment, The high quality for microstructure, electrical and optical properties of the as-deposited ITO films on unheated substrates is dominated by the sputtering parameters, The influence of the working gas pressure, DC power and oxygen partial pressure has been systematically investigated, The lowest DC power, and oxygen partial pressure has been systematically investigated, The lowest resistivity of ITO films deposited on PET substrates was 6$\times$10$^{-4}$ $\Omega$cm. It has been obtained at a working pressure of 3 mTorr and DC power of 30 W. The sheet resistance and optical transmittance of these film were 22 $\Omega$/square and 84% respectively. The best values of figures of merit for the electrical and optical characteristics such as T/ $R_{sh}$ and $T^{10}$ / $R_{sh}$ are approximately 38.1 and 7.95($\times$10$^{-3}$ $\Omega$$^{-1}$ ), respectively.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.3
• /
• pp.31-35
• /
• 2018

Tungsten disulfide($WS_2$) thin films were directly deposited by direct-current(DC) sputtering and annealed by rapid thermal processing(RTP) to materialize two-dimensional p-type transition metal dichalcogenide (TMDC) thin films on soda-lime glass substrates without any complicated exfoliation/transfer process. $WS_2$ thin films deposited at various DC sputtering powers from 80 W to 160W were annealed at different temperatures from $400^{\circ}C$ to $550^{\circ}C$ considering the melting temperature of soda-lime glass. The optical microscope results showed the stable surface morphologies of the $WS_2$ thin films without any defects. The X-ray photoelectron spectroscopy (XPS) results and the Hall measurement results showed stable binding energies of W and S and high carrier mobilities of $WS_2$ thin films.

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.688-694
• /
• 1999

Ti-6Al-4V-N films have been grown onto glass substrates by dc reactive magnetron sputtering from a Ti-6Al-4V-N alloy target at different nitrogen partial pressure, input powers and sputtering times. The influence of various sputtering conditions on structural properties of Ti-6Al-4V-N films was investigated by measuring their X-ray diffraction. The quaternary Ti-6Al-4V-N film is crystallizing in a face centered cubic TiN structure, the lattice parameter is smaller than the TiN parameter as titanium atoms of the TiN lattice are replaced by aluminum and vanadium atoms. The films show the (111) preferred orientation and the (111) peak intensity decreases as the nitrogen partial pressure is increased, but the intensity increases as the sputtering time is increased. The deposition rate and the grain size are alto related with the variation of various sputtering conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.52-53
• /
• 2005

$Y_2O_3$ film was directly deposited on Ni-3at%W substrate using DC reactive sputtering technique. Metallic yttrium was used for DC sputtering target and water vapor was used for oxidizing the deposited metallic Yttrium atoms on the substrate. The window of the water vapor turned out to be broad. The minimum partial pressure of water vapor was determined by sufficient oxidation of the $Y_2O_3$ film, and the maximum partial pressure of water vapor was determined by the non-oxidation of the target surface. As the sputtering power was increased, The deposition rate increased without narrowing the window. The fabricated $Y_2O_3$ films showed good texture qualities and surface morphologies. The YBCO film deposited directly on the $Y_2O_3$ buffered Ni-3at%W substrate showed $T_c$, $I_c$ (77 K, self field), and $J_c$ (77 K, self field) of 89 K, 64 A/cm and 1.l $MA/cm^2$, respectively.

• Journal of the Korean Ceramic Society
• /
• v.33 no.7
• /
• pp.735-742
• /
• 1996

Antimony-doped Tin oxide (ATO) thin films were deposited on soda-lime glass substrates by DC magnetron sputtering technique. Effects of DC power film thickness and post heat-treatment on electrical conductivity of ATO film were investigated. Other properties of ATO film such as optical anti-chemical and wear properties were also reported in this work. The obtained ATO films showed electrical resistivities ranging from 5$\times$10-3 $\Omega$cm to 3$\times$10-3 $\Omega$cm with the average optical transparency above 80% in visible wavelength range and excel-lent anti-chemical properties where the electrical resistivity was not changed even after soaking the films in 1M HCl or 1M NaOH solution for 10 days. These properties were found to be related to the crystallinity of ATO film and the films having higher crystallinity showed better properties.

• Korean Journal of Metals and Materials
• /
• v.47 no.6
• /
• pp.378-382
• /
• 2009

We investigated the effects of deposition conditions on the fabrication of $Fe_{3}O_{4}$ thin films using a reactive DC magnetron sputtering at room temperature. The structural, electrical, and magnetic properties of Fe oxide films dependence on the film thickness, oxygen flow rate, and the substrate crystallinity were also studied. We have successfully fabricated $Fe_{3}O_{4}$ film with thickness of about 10 nm under optimal reactive sputtering conditions. The saturation magnetization, resistivity, and Verwey transition of the $Fe_{3}O_{4}$ film were298 emu/cc, $4.0{\times}10^{-2}{\Omega}cm$, and 125 K, respectively.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.3
• /
• pp.27-32
• /
• 2004

High temperature superconducting coated conductor has a structure of /< superconducting layer>//. The buffer layer consists of multi layer, and the architecture most widely used in RABiTS approach is CeO$_2$(cap layer)/YSZ(diffusion barrier layer)/CeO$_2$(seed layer). Evaporation technique is used for the CeO$_2$ layer and DC reactive sputtering technique is used for the YSZ layer, A chamber was set up specially for DC reactive sputtering, Detailed features are as following. A separator divided the chamber into two halves a sputtering chamber and a reaction chamber. The argon gas for sputtering target elements flows out of the cap of sputtering gun, and water vapor for reaction with depositing species spouts near the substrate. Turbo pump is connected with reaction chamber. High speed deposition of YSZ film could be achieved in the chamber. Detailed deposition conditions (temperature and partial pressure of reaction gas) were investigated for the rapid growth of high quality YSZ film.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.500-501
• /
• 2005

Aluminum doped zinc oxide films (ZnO:Al) were deposited on glass substrate by DC magnetron sputtering from a ZnO target mixed with 2 wt% $Al_2O_3$. The effects of substrate bias on the electrical properties and film structure were studied. Films deposited with positive bias have been annealed at $600^{\circ}C$ using rapid thermal anneal (RTA) process. The effects of RTA on the evolution of film microstructure are to be also studied using X-ray diffraction, transmission electron microscopy, and atomic force microscopy. Positive bias sputtering may induce lattice defects caused by electron bombardments during deposition. The as-deposited film microstructure evolves from the film with high defect density to more stable film condition. The electrical properties of the films after RTA process were also studied and the results were correlated with the evolution of film microstructures.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.3
• /
• pp.117-124
• /
• 2007

The ITO films were deposited on glass substrates by RF-superimposed dc reactive magnetron sputtering and were annealed in $N_2$ vacuum furnace with temperatures in the range of $403K{\sim}573K$ for 30 minutes. Electrical, optical and structural properties of ITO films were examined with varying annealing temperatures from 403 K to 573 K. The resistivity of as-deposited ITO films was $5.4{\times}10^{-4}{\Omega}cm$ at the sputter conditions of applied RF/DC power of 200/200 W, $O_{2}$ flow of 0.2 seem and Ar flow of 0.2 seem. As a result of annealing in the temperature range of $403K{\sim}573K$, the crystallization occurred at 423 K that is lower than the crystallization temperature caused by a conventional sputtering method. And the resistivity decreased from $5.4{\times}10^{-4}{\Omega}cm\;to\;2.3{\times}10^{-4}{\Omega}cm$, the carrier concentration and mobility of ITO films increased from $4.9{\times}10^{20}/cm^3\;to\;6.4{\times}10^{20}/cm^3$, from $20.4cm^2/Vsec\;to\;41.0cm^2/Vsec$, respectively. The transmittance of ITO films in visible became higher than 90% when annealed in the temperature range of $423K{\sim}573K$. High quality ITO thin films made by RF-superimposed dc reactive magnetron sputtering and annealing in $N_2$ vacuum furnace will be applied to transparent conductive oxides of the advanced flat panel display.