• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2008년도 정보통신설비 학술대회
• /
• pp.414-417
• /
• 2008

This paper presents the design and analysis of 2.45GHz Low-IF Mixer using CMOS 0.18um. The Mixer is implemented by using the Gilbert-type configuration, current bleeding technique, and the resonating technique for the tail capacitance. And the design of this Double Balance Mixer is based on its lineaity since it is important in the interference cancellation system. The low flicker noise mixer is implemented by incorporating a double balanced Gilber-type configuration, the RF leakage-less current bleeding technique, and Cp resonating technique. The proposed mixer has a simulated conversion gain of 16dB a simulated IIP3 of -3.3dBm and P1dB is -19dBm. A simulated noise figure of 6.9dB at l0MHz and a flicker corner frequency of 510kHz while consuming only 10.65mW od DC power. The layout of Mixer for one-chip design in a 0.18-um TSMC process has 0.474mm$\times$0.39 mm size.

• 한국초전도ㆍ저온공학회논문지
• /
• 제24권4호
• /
• pp.50-54
• /
• 2022

High temperature superconducting (HTS) magnets for large-capacity energy storage system need to be composed of toroid magnets with high energy density, low leakage magnetic fields, and easy installation. To realize such a large capacity of a toroid HTS magnet, an HTS cable with large current capacity would be preferred because of the limited DC link voltage and instantaneous high power required for compensation of the disturbance in the power grid. In this paper, the optimal operating strategies of the SMES for peak load reduction of the microgrid system were calculated according to the load variation characteristics, and the effect of compensation of the frequency change in microgrid with a SMES were also simulated. Based on the result of the simulation, key design parameters of SMES coil were presented for two cases to define the specification of the HTS cable with large current capacities for winding of HTS toroid coils, which will be need for development of the HTS cable as a future work.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1925-1927
• /
• 1999

At the study, it has fabricated Al/AlN/GaAs MIS capacitor using DC reactive sputtering method. To applicate GaAs semiconductor in a MIS devices, investigated capability of AIN thin film by the insulator layer. Also it has investigated inversion of C-V characteristics by addition of the hydrogen(hydrogen concentration: 5%) and it has investigated that leakage current has $10^{-8}A/cm^2$ for 1 MV/cm breakdown electric field of I-V characteristics.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1402-1404
• /
• 2001

Josephson junction arrays of the type $Nb/Al-Al_2O_3/Nb$ were prepared by DC magnetron sputtering. The tunnel barrier was formed by in-situ thermal oxidation. Individual junctions were defined using selective niobium etching process(SNEP). The characteristic curves of Josephson junction arrays fabricated with and without cooling the substrate were represented. The junctions deposited without cooling showed poor characteristics(high leakage current, low gap voltage), and a high quality Josephson junction array of 2,000 junctions with high hysteresis was obtained with cooling and when operated at 74.6 GHz, it generated stable quantized voltage steps up to 2.2 V.

• 대한기계학회논문집B
• /
• 제27권7호
• /
• pp.829-836
• /
• 2003

Understanding of heat generation in semiconductor devices is important in the thermal management of integrated circuits and in the analysis of the device physics. Scanning thermal microscope was used to measure the temperature and the electric potential distribution on the cross-section of an operating metal-oxide-semiconductor field-effect transistor (MOSFET). The temperature distributions were measured both in DC and AC modes in order to take account of the leakage current. The measurement results showed that as the drain bias was increased the hot spot moved to the drain. The density of the iso-potential lines near the drain increased with the increase in the drain bias.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(2)
• /
• pp.900-903
• /
• 2003

An identification method of induction motor parameters such as rotor time constant and mutual inductance at standstill condition is discussed assuming that stator resistance and leakage has already been obtained applying two different DC voltage and single phase voltage to the induction motor, respectively. This proposed scheme is implemented by means of Model Reference Adaptive Control (MRAC) technique, which uses a rotor flux equation in voltage model as a reference model and one in current model and is demonstrated through experiment.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2003년도 추계학술대회
• /
• pp.335-343
• /
• 2003

In the electrode fabrication of unit cell, it was ascertained that electrochemical characteristics were greatly increased with 90 wt.% of BP-20, 5 wt.% of Super P and 5 wt.% of mixed binder [P(VdF-co-HFP) : PVP =7 : 3] The self-discharge of unit cell showed that diffusion process was controlled by the ion concentration difference of initial electrolyte due to the characteristics of Electric Double Layer Capacitor (EDLC) charged by ion adsorption in the beginning, but this by current leakage through the double-layer at the electrode/electrolyte interface had a minor effect and voltages of curves were remained constant regardless of electrode material. The electrochemical characteristics of 2.3 V/3,000 F grade EDLC were as follows: 0.35 m of DC-ESR (100 A discharge), 0.14 mof AC-ESR (AC amplitude 100 mV), 2.80 Wh/kg (3.73 Wh/L) of energy density and 4.64 kW /kg (6.19 kW/L) of power density. Power output was compatible with electric vehicle applications, uninterrupted power supply and engine starter, in due consideration of Ragone relations.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.258-261
• /
• 1997

The sealing integrity is related to the safe operation of arrester the prime failure reason of porcelain housed arresters is moisture ingress. To be a meaningful tests a polymer arrester sealing test must be a realistic acceleration of field service. We think the test should be an accelerating course of actual temperatures, the enduring property to mechanical load and temperatures should be considered together. A union test method consisting of the thermal mechanical test and thermal cycling test is proposed to test the sealing integrity of polymeric arresters, which uses dielectric loss, leakage current 1mA DC voltage and partial discharge as the diagnostic techniques, and the test results were presented. The comparison states that the TMTCUT method is suitable fur the test of sealing integrity of polymeric arresters. .

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.636-639
• /
• 1993

This paper is discribed the results of insulation characteristic tests that are DC leakage current, test, tan${\delta}$ test, AC breakdown test and observation of tree in the used 6.6kV CV cables. In the correlation of these tests, the tan${\delta}$ test stands for the main deterioration factor of cable insulation.

• 한국인터넷방송통신학회논문지
• /
• 제18권6호
• /
• pp.187-193
• /
• 2018

국내에서의 전력에 대한 수요는 점진적으로 증가하고 있는 추세이다. 수요에 대응하기 위한 발전소는 기능이 다양해지고 효율이 점차 커져야 한다. 발전소 내의 전력 기기에서 사고가 발생하면 막대한 경제적 손실 및 장애를 초래하게 된다. 사고 발생의 원인 중의 하나로서 절연 성능이 저하 된 케이블이 있다. 케이블 사고를 미연에 방지하기 위하여 절연의 상태를 감시하고 확인하여야 한다. 케이블 사고는 연결 부위인 접속에서 발생하는 사고가 대부분을 차지한다. 본 연구와 관련하여 우리는 접속부 상태를 판별하기 위한 장비를 개발하였고, 한국서부발전(주)의 현장에 설치하여 운용 중이다. 본 논문에서는 현장에서 설치 운용 중인 장비에 대한 설명과 더불어 설치 운용된 결과를 통해 케이블의 수명을 예측할 수 있는 고전압 케이블 접속재의 안정적 사용을 위한 온라인 감시진단기법 중에서 사고가 가장 빈번하게 발생하는 접속부에 대해 안정적인 사용을 위한 진단의 정확성과 신뢰성을 향상시키기 위한 연구를 하였다. 이 논문에서 하드웨어 구성을 위주로 우리가 개발한 장비를 소개한다.