• Nuclear Engineering and Technology
• /
• 제48권6호
• /
• pp.1376-1386
• /
• 2016

This study investigated the loading rate effect on the fracture resistance under cyclic loading conditions to understand clearly the fracture behavior of piping materials under seismic conditions. J-R fracture toughness tests were conducted under monotonic and cyclic loading conditions at various displacement rates at room temperature and the operating temperature of nuclear power plants (i.e., $316^{\circ}C$). SA508 Gr.1a low-alloy steel and SA312 TP316 stainless steel piping materials were used for the tests. The fracture resistance under a reversible cyclic load was considerably lower than that under monotonic load regardless of test temperature, material, and loading rate. Under both cyclic and monotonic loading conditions, the fracture behavior of SA312 TP316 stainless steel was independent of the loading rate at both room temperature and $316^{\circ}C$. For SA508 Gr.1a lowalloy steel, the loading rate effect on the fracture behavior was appreciable at $316^{\circ}C$ under cyclic and monotonic loading conditions. However, the loading rate effect diminished when the cyclic load ratio of the load (R) was -1. Thus, it was recognized that the fracture behavior of piping materials, including seismic loading characteristics, can be evaluated when tested under a cyclic load of R = -1 at a quasistatic loading rate.

• Geomechanics and Engineering
• /
• 제25권2호
• /
• pp.89-98
• /
• 2021

The paper presents an experimental study on the strength behaviour of a coral gravelly sand from Vietnam subjected to monotonic and cyclic loading. A series of direct shear tests were carried out to investigate the shear strength behaviour and the factors affecting the shear strength of the sand such as relative density, cyclic load, amplitude of the cyclic load and loading rate. The study results indicate that the shear strength parameters of the coral gravelly sand include not only internal friction angle but also apparent cohesion. These parameters vary with the relative density, cyclic load, the amplitude of the cyclic load and loading rate. The shear strength increases with the increase of the relative density. The shear strength increases after subjecting to cyclic loading. The amplitude of the cyclic load affects the shear strength of coral gravelly sand, the shear strength increases as the amplitude of the cyclic load increases. The loading rate has insignificantly effect on the shear strength of the coral gravelly sand.

• Journal of the Korean Society for Advanced Composite Structures
• /
• 제4권1호
• /
• pp.25-32
• /
• 2013

In real world applications, the response of structures may be dependent on the rate of loading and thus can be affected by transient loading, especially when the rate of loading is significant. In such situations, the rate of loading may become a major issue to understand structures during earthquake excitation or under blast or high velocity impact. In some cases, the rate effect on structures under strong earthquake excitation cannot be ignored when attempting to understand inelastic behavior of structures. Many researchers developed the constitutive theories in cyclic plasticity and viscoplasticity. In this study, numerical simulation by cyclic visocoplasticity models is introduced and analyzed. Finally, the analytical results are compared with experimental results as a means to evaluate and verify the model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제33권12호
• /
• pp.1366-1374
• /
• 2009

Anterior cruciate ligament(ACL) of human body experiences a large deformation. May during everyday when large deformation is repeated by various activities such as outdoor activity, ACL easily get damaged. In order to acknowledge the effect of the cyclic large deformation to ACL, the constitutive equations for ACL are derived from experiment data. The concept of the objective stress rate plays a important role wherever large deformation occurs. In order to obtain the objective stress rates the eigenprojection technique is used. A comparison is made for four different cases: Jaumann rate, Green-Naghdi rate, logarithmic rate and twirl tensor of Eulerian triad rate for an isotropic material subject to cyclic deformation, such as simple shear motion. Four different materials are studied to compare the behavior of the materials for ACL using different objective rates. Finally, more complicated model with fibers for soft tissues is used to calculate the behavior subjected to cyclic large deformation.

• Structural Engineering and Mechanics
• /
• 제7권5호
• /
• pp.457-471
• /
• 1999

In this paper, different curvature-rates are controlled to highlight the characteristic of viscoplastic response in cyclic bending tests. The curvature-ovalization apparatus, which was designed by Pan et al. (1998), is used for conducting the curvature-controlled experiments on thin-walled tubular specimens for AISI 304 stainless steel under cyclic bending. The results reveals that the faster the curvature-rate implies, the fast degree of hardening of the metal tube. However, the ovalization of the tube cross-section increases when the curvature-rate increases.

• Journal of Ocean Engineering and Technology
• /
• 제6권1호
• /
• pp.78-86
• /
• 1992

The creep behaviors of 1%Cr-Mo-V and 12%Cr steam turbine rotor steels under static or cyclic load were examined at 600 and $700^{\circ}C$. The relationship between these two kinds of phenomena was studied and the experimental results were summarized as follows: 1) It is confirmed that the cyclic creep strain dependent on time is more available for creep, behavior analysis according to frequency change than that dependent on number of cycles, and the static creep, the special case of cyclic creep with stress ratio of 1 can be also more effectively analyzed by time-dependence. 2) The steady cyclic creep rate vs. the steady static creep rate, increases according to the increase of stress ratio, and this phenomena may occur on occasion of the decrease of the internal stress. 3) The initial strain affects on all the creep properties of the transient region, the steady state region and the rupture time in cyclic creep as well as static creep, and the quantitative relationships among them exist.

• Journal of Korean Vacuum Science & Technology
• /
• 제4권1호
• /
• pp.18-22
• /
• 2000

For the enhancement of the nucleation density of the diamond film, we introduced the cyclic process. The cyclic process was carried out by the on/off control of CH$_4$ flow rate for a relatively short time (10 min), compared with the total reaction time (6 h). Prior to depositing the diamond film, we made the pretreated glass substrate via the unidirectional scratch using ∼l $\mu\textrm{m}$ size diamond powders. Diamond films were deposited on the pretreated glass substrate in a microwave plasma enhanced chemical vapor deposition (MPECVD) system. We observed the enhancement of the nucleation density of the diamond films caused by the cyclic process. Detailed surface morphologies of the substrate were investigated after the cyclic process. Based on these results, we discussed the cause for the enhancement of the nucleation density on the pretreated glass substrate by the cyclic process.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제33권9C호
• /
• pp.643-651
• /
• 2008

In this paper, we propose a method to determine the optimal cyclic delay value of cyclic delay diversity(CDD) in orthogonal frequency division multiplexing(OFDM) systems. As the cyclic delay value increases, we can get signal to interference and noise ratio(SINR) gain by diversity effect, while SINR loss increases because of channel estimation errors. If the optimal delay value obtained by the proposed method is applied to CDD scheme, we can minimize the required SINR for a given FER(frame error rate) under the above mentioned trade-off.

• Journal of The Korean Society of Agricultural Engineers
• /
• 제52권3호
• /
• pp.73-79
• /
• 2010

In the present study, the loading frequency dependencies of cyclic shear strength and elastic shear modulus of reconstituted clay were examined by performing undrained cyclic triaxial tests and undrained cyclic triaxial tests to determine deformation properties. The result of undrained cyclic triaxial test of reconstituted and saturated clay shows that a faster frequency leads to higher stress amplitude ratio, but when the frequency becomes fast up to a certain point, the stress amplitude ratio will reach its maximum limit and the frequency dependence becomes insignificant. And also, the result of undrained cyclic triaxial deformation test shows a fact that a faster loading frequency leads to higher equivalent shear modules and smaller hysteresis damping ratio, and confirms the frequency dependence of cohesive soil. Meanwhile, the result of the creep test shows that continuing creep is created in the undrained cyclic triaxial test with slow loading frequency rate, and since loading rate becomes slower at the vicinity of the maximum and the minimum deviator stress due to sine wave loading, the vicinity of the maximum and the minimum deviator stress shall be more influenced by creep.

• Proceedings of the Korean Society for Quality Management Conference
• /
• 한국품질경영학회 1998년도 The 12th Asia Quality Management Symposium* Total Quality Management for Restoring Competitiveness
• /
• pp.277-286
• /
• 1998

This paper investigates the problem of determining optimal replacement policies for equipment subject to failures with cyclic rates. In many situations, the system failures depend on the operating environmental conditions that vary on time, usually with periodical manners. We use nonhomogeneous Poisson processes whose rate functions exhibit cyclic behavior as well as a long-term evolutionary trend to model the stochastic process of the failures when the rate of occurrence of the failures varies periodically, for example from day to day or between seasons. In this study, we compare optimal policies under the nonhomogeneous process with/without a cyclic component in the failure rate function. The analytical results for various situations are presented along with numerical examples using simulated data.