• The KIPS Transactions:PartA
• /
• v.17A no.1
• /
• pp.27-32
• /
• 2010

Logical Effort is a simple hand-calculated method that measures quick delay estimation. It has the advantage of reducing the design cycle time. However, it has shortcomings in designing a path for minimum area or power under a fixed-delay constraint. In this paper, we propose an equal delay model and, based on this, a method of optimizing power-delay efficiency in a logical path. We simulate three designs of an eight-input AND gate using our technique. Our results show about 40% greater efficiency in power dissipation than those of Logical Effort method.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2008.10b
• /
• pp.449-454
• /
• 2008

Finding an energy efficient route is one of the very important issues in the wireless sensor networks. The route scheme should consider both of the energy level of sensor nodes and the number of hops at the same time. First of all, this paper proposes an optimum routes finding scheme (ORFS), which could be used in the sensor network routing protocols. The scheme uses an optimum value for the path with the considerations of both the minimum energy level of a path and the number of hops at the same time. After that, this paper proposes a routing protocol based on the ORFS for how it could be used for the multipath directed diffusion with data aggregation (MDD-A), to get the better energy efficiency. The analysis result shows that the proposed routing protocol could lengthen the network life cycle about 18.7% compared to the previous MDD-A related protocols.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.12
• /
• pp.2343-2348
• /
• 2008

Ant algorithm is new meta heuristic for hard combinatorial optimization problem. It is a population based approach that uses exploitation of positive feedback as well as greedy search. It was first proposed for tackling the well known Traveling Salesman Problem. In this paper, we propose the improved $AS_{rank}$ algorithms. The original $AS_{rank}$ algorithm accomplishes a pheromone updating about only the paths which will be composed of the optimal path is higher, but, the paths which will be composed the optimal path is lower does not considered. In this paper, The proposed method evaporate the pheromone of the paths which will be composed of the optimal path is lowest(worst tour path), it is reducing the probability of the edges selection during next search cycle. Simulation results of proposed method show lower average search time and average iteration than original ACS.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.11a
• /
• pp.197-205
• /
• 2000

Productivity of container cranes and gantry cranes is influenced by the performance of crane hardware and cycle time. Cycle time in container handling is influenced by the path of containers and relative positioning of containers. So we have to minimize the sway of containers and spreaders to minimize relative positioning time. And sway minimization is influenced by the skill of workers in manual gantry cranes. In this paper, we will survey some anti-sway systems. Each system has some merits and some shortages. And we will show our choice and its experimental equipment which is under construction.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1350-1354
• /
• 2007

As the importance of low power design is emphasized, power consumption became one of the standards that represent the performance of the system. The purpose of this study is to decide design variable that minimize power consumption for the oxygen concentrator in two bed-one compressor 8 step PSA process that has above 90% purity at 3lpm by using given constants and selected parameters. Setting selected parameters as cycle time and equalization time, optimization for PSA process in the oxygen concentrator is progressed. For this, we need to know the features and basic principals of PSA process and to deduce objective function of performance analysis. Validations for objective function and lots of experiments are needed too. By using the characteristic curve of the compressor and the pressure curve of the process for 1 cycle, objective function was set. After theoretical 2 dimensional optimized paths was obtained. And then, by experiment, theoretical optimized path was verified.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.428-433
• /
• 2002

There have been many studies to visualize the vibration and noise of rotary compressor. Most of these studies assumed that the signal is stationary and the time-averaged signal is used for visualization. However, the noise and vibration signals generated during one cycle of crank shaft vary continuously. In this paper, the noise and vibration of rotary compressor which vary continuously are visualized by short time fourier transform method. The location of source and the transfer path of vibration and noise at arbitrary frequencies, which can not be visualized by averaged signal, can be visualized clearly.

• Communications of the Korean Mathematical Society
• /
• v.24 no.2
• /
• pp.161-169
• /
• 2009

In this paper, we introduce the generalized ideal-based zero-divisor graph structure of near-ring N, denoted by $\widehat{{\Gamma}_I(N)}$. It is shown that if I is a completely reflexive ideal of N, then every two vertices in $\widehat{{\Gamma}_I(N)}$ are connected by a path of length at most 3, and if $\widehat{{\Gamma}_I(N)}$ contains a cycle, then the core K of $\widehat{{\Gamma}_I(N)}$ is a union of triangles and rectangles. We have shown that if $\widehat{{\Gamma}_I(N)}$ is a bipartite graph for a completely semiprime ideal I of N, then N has two prime ideals whose intersection is I.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.163-169
• /
• 2003

The vertical roller mill is the important machine grinding and mixing various crude materials in the manufacturing process of portland cement. Table liner is one of grinding elements of vertical roller mill and is subjected to the cyclic bending stress by rollers load and the centrifugal force by rotation of table. It demands $4{\times}10^7$ cycle but has $4{\times}10^6{\sim}8{\times}10^6$ cycle. It fractures at the edge of grinding path of outside roller. The repair expense for it amounts to 30% of total maintenance of vertical roller mill. Therefore, this study shows the fracture mechanism of table liner for vertical roller mill using HDM and fatigue analysis

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1130-1135
• /
• 2004

The vertical roller mill is the important machine grinding and mixing various crude materials in the manufacturing process of portland cement. Vertical roller mill is subjected to the cyclic bending stress by rollers load. It demands $4{\times}10^7$ cycle but has $4{\times}10^6{\sim}8{\times}10^6$ cycle. It fractures at the edge of grinding path of outside roller. The repair expense for it amounts to 30% of total maintenance. Therefore, this study shows optimal design for vertical roller mill using DOE and neural network.

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.2
• /
• pp.33-38
• /
• 2012

The wafer positioning robot in the semiconductor industry is required to operate at high speed for the improvement of productivity. The residual vibration caused by the high speed of the wafer positioning robot, however, makes the life of the robot shorter and the cycle time longer. In this study, the input shaping and the path of the system are designed for the reduction of the residual vibration and the improvement of the cycle time. The followings are the process for the reduction and the improvement; 1) System modeling of the wafer positioning robot, 2) Verification of dynamic characteristics of the wafer positioning robot, 3) Input shaping plan using impulse response reiteration, 4) Simulation test using SIMULINK program, 5) Analysis of result.