• Journal of the Institute of Electronics Engineers of Korea TC
• /
• 제43권10호
• /
• pp.90-97
• /
• 2006

We report our research work on the millimeter-wave broadband amplifier integrating the shunt peaking technology with the cascode configuration. The millimeter-wave broadband cascode amplifier on MIMIC technology was designed and fabricated using $0.1{\mu}m\;{\Gamma}-gate$ GaAs PHEMT, CPW, and passive library. The fabricated PHEMT has shown a transconductance of 346.3 mS/mm, a current gain cut off frequency ($f_T$) of 113 GHz, and a maximum oscillation frequency ($f_{max}$) of 180 GHz. To prevent oscillation of designed cascode amplifier, a parallel resistor and capacitor were connected to drain of common-gate device. For expansion of the bandwidth and flatness of the gain, we inserted the short stub into bias circuits and the compensation transmission line between common-source device and common-gate device, and then their lengths were optimized. Also, the input and output stages were designed using the matching method to obtain the broadband characteristic. From the measurement, we could confirm to extend bandwidth and flat gain by integrating the shunt peaking technology with the cascode configuration. The cascode amplifier shows the broadband characteristic from 19 GHz to 53.5 GHz. Also, the average gain of this amplifier is about 6.5 dB over the bandwidth.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• 제41권11호
• /
• pp.21-27
• /
• 2004

In this paper, millimeter-wave monolithic integrated circuit(MIMIC) low noise amplifier(LNA) for V-band, which is applicable to 60 GHz wireless local area network(WLAN), was fabricated using the high performance 0.1 ${\mu}{\textrm}{m}$ $\Gamma$-gate pseudomorphic high electron mobility transistor(PHEMT). The DC characteristics of PHEMT are drain saturation current density(Idss) of 450 mA/mm and maximum transconductance(gm, max) of 363.6 mS/mm. The RF characteristics were obtained the current gain cut-off frequency(fT) of 113 GHz and the maximum oscillation frequency(fmax) of 180 GHz. V-band MIMIC LNA was designed using active and passive device library, which is composed of 0.1 ${\mu}{\textrm}{m}$ $\Gamma$-gate PHEMT and coplanar waveguide(CPW) technology. The designed V-band MIMIC LNA was fabricated using integrated unit processes of active and passive device. The measured results of V-band MIMIC LNA are shown S21 gain of 21.3 dB, S11 of -10.6 dB at 60 GHz and S22 of -29.7 dB at 62.5 GHz. The measured result of V-band MIMIC LNA was shown noise figure (NF) of 4.23 dB at 60 GHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• 제41권12호
• /
• pp.7-12
• /
• 2004

In this paper, CPW wideband distributed amplifier was designed and fabricated using 0.1 $\mum$ InGaAs/InAlAs/GaAs Metamorphic HEMT(High Electron Mobility Transistor). The DC characteristics of MHEMT are 442 mA/mm of drain current density, 409 mS/mm of maximum transconductance. The current gain cut-off frequency(fT) is 140 GHz and the maximum oscillation frequency(fmax) is 447 GHz. The distributed amplifier was designed using 0.1 $\mum$ MHEMT and CPW technology. We designed the structure of CPW curve, tee and cross to analyze the discontinuity characteristics of the CPW line. The MIMIC circuit patterns were optimized electromagnetic field through momentum. The designed distributed amplifier was fabricated using our MIMIC standard process. The measured results show S21 gain of above 6 dB from DC to 45 GHz. Input reflection coefficient S11 of -10 dB, and output reflection coefficient S22 of -7 dB at 45 GHz, respectively. The chip size of the fabricated CPW distributed amplifier is 2.0 mm$\times$l.2 mm.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• 제39권1호
• /
• pp.18-24
• /
• 2002

n this paper, we have fabricated pseudomorphic high electron mobility transistors (PHEMT) with a 0.2 ${\mu}{\textrm}{m}$ wide-head T-shaped gate using electron beam lithography by a dose split method. To make the T-shape gate with gate length of 0.2 ${\mu}{\textrm}{m}$ and gate head size of 1.3 ${\mu}{\textrm}{m}$ we have used triple layer resist structure of PMMA/P(MMA-MAA)/PMMA. The DC characteristics of PHEMT, which has 0.2 ${\mu}{\textrm}{m}$ of gate length, 80 ${\mu}{\textrm}{m}$ of unit gate width and 4 gate fingers, are drain current density of 323 ㎃/mm and maximum transconductance 232 mS/mm at $V_{gs}$ = -1.2V and $V_{ds}$ = 3V. The RF characteristics of the same device are 2.91㏈ of S21 gain and 11.42㏈ of MAG at 40GHz. The current gain cut-off frequency is 63GHz and maximum oscillation frequency is 150GHz, respectively.ively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• 제18권8호
• /
• pp.887-894
• /
• 2007

In this paper, design and fabrication of the LPF with controllable four transmission zeros using electric coupling and added open stub is presented. Pass-band of the LPF is GSM band, and two transmission zeros are generated by the electric coupling at the WiBro and S-DMB band, And the other two transmission zeros are generated by the open stub at the upper frequencies. Harmonic frequency of the stop-band is suppressed by the realization of the filter using quasi-lumped element with small parasitic values. $C_M$, which is the electric coupling element of the equivalent circuit, is realized by the distance control between the open stubs of the filter structure. The fabricated LPF used teflon substrate with relative permittivity of 2.6. And it has a size of $38{\times}20{\times}0.79 mm^3$, which is including a feed line. The measured 3 dB cut-off frequency is 1.55 GHz, and locations of the transmission zeros are 2.20, 2.43, 4.11 and 6.84 GHz, respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권1호
• /
• pp.45-51
• /
• 2015

In this paper, we study the RF characteristics of the short wavelength thin-film transmission line employing microstrip line (ML)/coplanar waveguide (CPW) composite structure on silicon substrate for application to RFIC (radio frequency integrated circuit). The thin-film transmission line employing ML/CPW composite structure showed a wavelength shorter than conventional transmission lines. Concretely, at 10 GHz, the wavelength of the transmission line employing ML/CPW composite structure was 6.26 mm, which was 60.5 % of the conventional coplanar waveguide. We also extracted the bandwidth characteristic of the transmission line employing ML/CPW composite structure using equivalent circuit analysis. The S parameter of the equivalent circuit showed a good agreement with measured result. According to the bandwidth extraction result, the cut-off frequency of thin-film transmission line employing ML/CPW composite structure was 377 GHz. Above results indicate that the transmission line employing ML/CPW composite structure can be effectively used for application to broadband and compact RFIC.

• Journal of the Korean Vacuum Society
• /
• 제17권5호
• /
• pp.408-418
• /
• 2008

The rectangular resonant cavity was designed and characterized as a microwave plasma source for focused ion beam. The optimum cavity was calculated analytically and analyzed in detail by using HFSS(High Frequency Structure Simulator). Since the resonant cavity can be affected by the permittivity of quartz chamber and plasma, the cavity is designed to be changeable in one direction. By observing the microwave input power at which the breakdown begins, the optimum cavity length for breakdown is measured and compared with the calculated one, showing in good agreement with the optimum length reduced by 10cm according to the permittivity change in the presence of quartz chamber. The shape of breakdown power curve as a function of pressure appears to be similar to Paschen-curve. After breakdown, plasma densities increase with microwave power and the reduced effective permittivity in the cavity with plasma results in larger optimum length. However, it is not possible to optimize the cavity condition for high density plasmas with increased input power, because too high input power causes expansion of density cutoff region where microwave cannot penetrate. For more accurate microwave cavity design to generate high density plasma, plasma column inside and outside the density cutoff region needs to be treated as a conductor or dielectric.

• The Journal of the Acoustical Society of Korea
• /
• 제38권6호
• /
• pp.637-650
• /
• 2019

This paper analyzes the limitations of binaural sound that is reproduced with headphones based on Ambisonics for Virtual Reality (VR) audio. VR audio can be provided with binaural sound that compensates head rotation of a listener. Ambisonics is widely used for recording and reproducing ambient sound fields around a listener in VR audio, and the First order Ambisonics (FOA) is still being used for VR audio because of its simplicity. However, the maximum frequencies with this order is too low to perfectly reproduce ear signals, and thus the binaural reproduction has inherent limitations in terms of spectrum and sound localization. This paper investigates these limitations by comparing the signals arrived at ear positions in the reference field and the reproduced field. An incidence wave is defined as a reference field, and reproduced over virtual loudspeakers. Frequency responses, inter-aural level differences, and inter-aural phase differences are compared. The results show, above the maximum cut off frequency in general, that the reproduced levels decrease, and the horizontal localization can be provided only around the forward direction.

• Journal of Nutrition and Health
• /
• 제41권5호
• /
• pp.414-427
• /
• 2008

The purpose of the study was to develop an eating habit checklist for screening elementary school children at high risk of energy overintake. Dietary habits, food intake, anthropometric data were collected from 142 children (80 boys and 62 girls) in the 4th to 6th grades of elementary schools. Energy intake, fat intake, and percentage of Estimated Energy Requirement (%EER) were used as indices to detect the risk of energy overintake of the children. Pearson correlation coefficients were calculated between dietary habit scores and energy overintake indices in order to select questions included in the checklist. TV watching during the meal, meal speed, meal amount, overintake frequency, eatingout frequency, snack frequency, frequency of eating Ramyun or fast foods showed significant correlations with energy overintake indices. Stepwise regression analysis was performed to give each item a different weight by prediction strength. To determine the cut-off point of the test score, sensitivity, specificity, and positive predictive values were calculated. The 7-item checklist with test results from 0 to 13 points was developed, and those with equal or higher than 5 points were diagnosed as a risk group of energy overintake. Among our subjects 13.4% was diagnosed as the risk group. Mean energy intake of the subjects in the risk group and the normal group were 2,650 kcal and 1,640 kcal, respectively. However, there were no significant differences of Index of Nutritional Quality (INQ) of the other nutrients except eating fiber between the risk group and the normal group. This checklist will provide a useful screening tool to identify children at high risk of energy overintake.

• Korean Journal of Applied Biomechanics
• /
• 제17권2호
• /
• pp.217-226
• /
• 2007

Putting score counts about 43 % of the golf score. The dominant idea of the putting motion to amateur golfers as well as to many professional golfers is a pendulum-like motion. If a golfer's putting stroke motion is a pendulum-like motion, the putting motion should be straight-back-and-through, the same backswing, downswing, and follow through length and period, and a swing with a fixed hinge joint. If the putting motions of the human are different from the pendulum motion, there could be confusion in understanding and teaching golf putting. The purpose of this study was to examine the center of rotation(COR) of the putter head to reveal whether professional golfers really putt like a pendulum. Thirteen male professional golfers were recruited for the study. Each golfers executed 10.94 m putts six times on an artificial grass mat. Putter head position data were collected through a 60 Hz three-dimensional motion analysis system and low pass filtered with cut-off frequency of 6 Hz. COR of the putter head was mathematically acquired. Each golfer's last five putting motions were considered. The results show that the COR of the putter head was neither fixed nor located inside of the golfer. The medio-lateral directional component of the COR of the putter head fluctuated in the range of 10 cm during downswing and follow through. The anterior-posterior directional component of the COR of the putter head was fixed from the beginning of the downswing through impact. Just after impact, however, it moved to the target up to 60 cm. The superior-inferior directional component of COR of the putter head moved in a superior direction with the beginning of the downswing and showed peak height just prior to impact. During the follow through, it moved back in an inferior direction. The height-normalized peak value of the COR of the putter head was $1.4{\pm}0.3$ height. Technically speaking, male professional golfers' 10.94 m putting motion is not a pendulum-like motion. The dominating idea of a pendulum-like motion in putting might come from the image of the flawless, smooth motion of a pendulum.