• 대한전자공학회논문지
• /
• 제22권5호
• /
• pp.69-74
• /
• 1985

본 논문에서는 먼저 Sensitivity가 가장 낮은 LC Ladder 필터로 부터 FDNR frequency dependent negative resists.) 방식을 이용하여 5차 Butterworth 저역 통과 능동 RC필터를 설계하였으며 능동 RC 필터를 SCF(switched capacito, filter)로 변조하는 과정에서 Bilinear Z변환을 이용하였다. Bilinear Z 변환으로 설계된 SCF에서 aliasing 현상은 피할수 있으나 주파수 대곡이 발생한다. 아나로그 필터를 디지틀 릴터로 변환하면 이러한 영향으로 속단 주파수 영역이 일치하지 않으므로 이것을 적게 하기 위하여 Prewarping을 해준다. 그 결과 Prewarping된 SCF는 Bilinear Z 변환된 SCF보다 각파수 이유이 현저하게 개선됨을 확인하였다.

• 대한전자공학회논문지SD
• /
• 제44권12호
• /
• pp.1-6
• /
• 2007

본 논문에서 기존에 사용하고 있는 metamorphic high electron transistor (MHEMT)의 채널에 InP를 추가하여 제작 하였다. InP는 In0.53Ga0.47As와 비교하여 낮은 충돌 이온화 계수를 가지고 있다. 그런 특성을 MHEMT의 문제점 중의 하나인 낮은 항복전압의 개선에 이용하였다. 우리는 기존의 MHEMT와 InP 합성 채널 MHEMT의 항복 특성과 주파수 특성을 비교 하였다. 본 논문에서 InP 합성 채널 MHEMT의 on-state와 off-state 항복전압이 각각 2.4와 5.7 V가 측정 되었고 또한 cut-off 주파수와 maximum oscillation 주파수는 각각 160 GHz와 230 GHz가 측정 되었다. 위의 결과는 InP 합성 채널 MHEMT가 밀리미터파 대역의 전력용 소자에 이용되는데 큰 장점을 갖는 소자임을 알 수 있다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.965-969
• /
• 2003

In this paper, the implementation technique of digital crossover network using perfect linear phase IIR filters is presented. This system has various advantages which cannot be obtained from analog crossover network such as linear phase response, flat group delay and sharp cut-off at low-order over audio frequency band. The simulation results show that the group delay response is maximally flat and twice more attenuation in stop-band than the prototype elliptic IIR filter at all desired frequency.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(2)
• /
• pp.88-91
• /
• 2000

An MMIC oscillator operating at the 24.55 GHz has been designed using 0.2 ${\mu}{\textrm}{m}$AlGaAs/InGaAs/GaAs Pseudomorphic HEMT technology. The active device used in the oscillator design has a 0.2 ${\mu}{\textrm}{m}$ gate length PHEMT with 4$\times$80 ${\mu}{\textrm}{m}$ gate width. We obtained 4.08 dB of S$_{21}$ gain and 317 mS/mm of transconductance, and extrapolated unit current gain cut-off frequency (f$_{T}$) and maximum oscillation frequency (fmax) were 62 GHz and 120 GHz, respectively. The circuit are based on a series feedback and negative resistance topology. Microstrip line open stub is used to terminating. The oscillator circuits has designed for delivering maximum power to load and conjugated matching. The simulated small signal negative resistance was 50 Ω. We obtained 1.002 of loop gain and 0.0005$^{\circ}$angle from the simulation by HP libra 6.1. The layout for oscillator is 1.2$\times$1.8 $\textrm{mm}^2$.>.

• 한국정밀공학회지
• /
• 제7권3호
• /
• pp.48-55
• /
• 1990

A new curve fitting algorithm based on modal analysis is introduced for extracting the modal parameters from the measured frequency responses. To compensate the effect of cut-off frequency ranges the transfer function including residual mass and residual flexibility is employed. Model parameters are computed from the newly defined form of transfer function in a simple way. The accuracy of this algorithm is proved by applying to the 3 degrees of freedom model and vibration of cantilever beam.

• 한국압력기기공학회 논문집
• /
• 제5권1호
• /
• pp.20-24
• /
• 2009

There is extensive tubing pipe in the nuclear power plant under high temperature and pressure. Erosion and corrosion defects are expected on this tubing pipe due to environmental and mechanical factors. In this study, Guided Ultrasonic Wave technique was applied to detect defects. The technique explores the advantages of the Guided Ultrasonic Wave method that inspects along the wall of the pipe and can travel long distances, providing rapid collection of data. This paper presents a case study of the Guided Ultrasonic Wave testing of 3/8" tubing pipe. This study offers to understand detected signals through correlation between amplitude and depth of defects.

• Wind and Structures
• /
• 제4권1호
• /
• pp.63-72
• /
• 2001

This paper presents results of a study on wind loads and wind induced dynamic response of bridge jointed twin-towered buildings. Utilizing the high-frequency force balance technique, the drag and moment coefficients measured in wind tunnel tests, and the maximum acceleration rms values on the top floor of towers, are analyzed to examine the influence of building's plan shapes and of intervals between towers. The alongwind, acrosswind and torsional modal force spectra are investigated for generic bridge jointed twin-towered building models which cover twin squares, twin rhombuses, twin triangles, twin triangles with sharp corners cut off, twin rectangles and individual rectangle with the same outline aspect ratio as the twin rectangles. The analysis of the statistical correlation among three components of the aerodynamic force corroborated that the correlation between acrosswind and torsional forces is significant for bridge jointed twin-towered buildings.

• 대한전자공학회논문지
• /
• 제27권5호
• /
• pp.737-746
• /
• 1990

Ga0.47In0.53As PIN photodiodes(PD) having various areas have been fabricated by liquid phase epitaxial techniques. Ternary melt has been baked out at 675\ulcorner in H2 atmosphere for 20 hours before growth, which resulted in reduction of background carrier concentration of grown epi-layer. Also, lattice mismatch has been controlled within 0.01%. The room temperature performance of 10**-4cm\ulcornerarea PIN PD at a bias voltage of -5V were` quantum efficiency(with no antireflection coating)=60% for 1.3\ulcorner light source, dark current\ulcorner5nA, and capacitance\ulcornerpE. Frequency response measurement of packaged PIN PD has shown that cut-off frequency (f-3dB) was 961MHz. This PD has shown a good eye pattern when it was incorporated in a 565Mbps optical receiver.

• 한국전기전자재료학회논문지
• /
• 제23권5호
• /
• pp.424-428
• /
• 2010

This paper describes the design and analysis of AlN piezoelectric micro energy harvester. The harvester was designed to convert ambient vibration energy to electrical power as a AlN piezoelectric material compatible with CMOS (complementary metal oxide semiconductor) process. To cut off the leakage current, AlN was used as the insulating layer. Also, Mo was used for the excellent c-axis crystal growth as the bottom electrode. The AlN harvester which it has the low operating frequency was designed by using the ANSYS FEA (finite element analysis). From the simulation results, the resonance frequency of designed model is about 360 Hz and analyzed the bending mode, displacement and expectation output.

• Journal of Genetic Medicine
• /
• 제10권1호
• /
• pp.52-56
• /
• 2013

Mosaic trisomy 14 syndrome is a well-known but unusual chromosomal abnormality with a distinct and recognizable phenotype. Array comparative genomic hybridization (CGH) analysis has recently become a widely used method for detecting DNA copy number changes, in place of traditional karyotype analysis. However, the array CGH shows a limitation for detecting the low-level mosaicism. Here, we report the detailed clinical and cytogenetic findings of patient with low-frequency mosaic trisomy 14, initially considered normal based on usual cut-off levels of array CGH, but confirmed by G-banding karyotyping. Our patient had global developmental delay, short stature, congenital heart disease, craniofacial dysmorphic features, and dark skin patches over her whole body. Estimated mosaicism proportion was 23.3% by G-banding karyotyping and 18.0% by array CGH.