• The KIPS Transactions:PartD
• /
• v.11D no.3
• /
• pp.597-604
• /
• 2004

Accurate software cost estimation is essential to both developers and customers. Most of the cost estimating models based on the size measure methods, such as LOC and FP, are obtained through size estimation. The accuracy of size estimation directly influences the accuracy of cost estimation. As a result, the overall structure of regression-based cost models applies the power function based on software size. Many growth phenomenon in nature such as the growth in living organism, performance of technology, and learning capability of human show an S-shaped curve. This paper proposes a model which estimates the developing effort by using the growth curve. The presented model assumes that the relation cost and size follows the growth curve. The appropriateness of the growth curve model based on Function Point, Full-Function Point and Use-Case Point, which are the general methods in estimating the software size have been confirmed. The proposed growth curve model shows similar performance with power function model. In conclusion, the growth curve model can be applied in the estimation of the software cost.

• Journal of the Korean Society of Safety
• /
• v.28 no.1
• /
• pp.63-73
• /
• 2013

Dynamic strain history curve measured in the field is influenced by various factors such as vehicle type, speed, noise, temperature and running location etc.. Because such curve is used for vehicle weight estimation methodology suggested by Moses, exact strain history curve is the most important thing for exact estimation of vehicle weight. In this paper, effect of such factors mentioned above is investigated on the measured strain history curves, and results of weight estimation of vehicles are discussed quantitatively. From this study, it was known that temperature effect contained in the strain history curve measured for long time in-site gives the biggest effect on result of weight estimation and it can be removed by using the mode value. Furthermore, gross vehicle weight can be estimated within 5% error corresponding to A class of the European classification if effects of temperature and noise are removed and vehicle properties such as speed, axle arrangement and running location are considered properly.

• The KIPS Transactions:PartB
• /
• v.14B no.4
• /
• pp.241-248
• /
• 2007

An L-curve corner detection method is proposed for the determination of the regularization parameter in optical flow estimation. The method locates the positive peak whose curvature difference from the just right-hand negative valley is the maximum in the curvature plot of the L-curve. while the existing curvature-method simply finds the maximum in the plot. Experimental results show that RMSE of the estimated optical flow is greater only by 0.02 pixels-per-frame than the least in the average sense. The proposed method is also compared with an existing curvature-method and the adaptive pruning method, resulting in the optical flow estimation closest to the least RMSE.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10a
• /
• pp.12-15
• /
• 1996

In this paper, a new shape control law is derived as a result of introducing the parametric curve representation. This control alw is based on the estimation of the curve parameters corresponding to the target joint positions and the target tip position. Estimating target curve parameters makes it possible to find, easily, a simple shape control law by the Lyapunov design method.

• Journal of the Korean Mathematical Society
• /
• v.61 no.4
• /
• pp.743-760
• /
• 2024

In this paper, we are devoted to study a forth order curve flow for a smooth closed curve in centro-affine geometry. Firstly, a new evolutionary equation about this curve flow is proposed. Then the related geometric quantities and some meaningful conclusions are obtained through the equation. Next, we obtain finite order differential inequalities for energy by applying interpolation inequalities, Cauchy-Schwartz inequalities, etc. After using a completely new symbolic expression, the n-order differential inequality for energy is considered. Finally, by the means of energy estimation, we prove that the forth order curve flow has a smooth solution all the time for any closed smooth initial curve.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.390-400
• /
• 2010

BNWF(Beam on Nonlinear Winkler Foundation) method has long been adopted for lateral behavior analysis of pile foundation and widely recognized for its simplicity and accuracy up until now. However, due to lateral load tests which were done in limited conditions and theory-based input Parameter estimation, the applicbility of p-y curve has not been fully examined. Accordingly, we researched on the applicability of conventional input parameter estimation and the p-y curve to be determined by the estimation through inverse analysis based on lateral load tests.

• Management Science and Financial Engineering
• /
• v.11 no.3
• /
• pp.125-136
• /
• 2005

As the importance of time-based competition is increasing, information systems for supporting the immediate decision making is strongly required. Especially high -tech product firms are under extreme pressure of rapid response to the demand side due to relatively short life cycle of the product. Therefore, the objective of our research is proposing a framework of estimating demand curve based on e-auction data, which is extremely easy to access and well reflect the limited demand curve in that channel. Firstly, we identify the advantages of using e-auction data for full demand curve estimation and then verify it using Agent-Eased-Modeling and Tobin's censored regression model.

• Communications for Statistical Applications and Methods
• /
• v.18 no.2
• /
• pp.179-187
• /
• 2011

The purpose of a Phase I clinical trial is to estimate the maximum tolerated dose, MTD, of a new drug. In this paper, the MTD estimation method is suggested by curve fitting the dose-toxicity data to an S-shaped curve. The suggested MTD estimation method is compared with established MTD estimation procedures using a Monte Carlo simulation study.

• Journal of Korea Multimedia Society
• /
• v.25 no.8
• /
• pp.991-998
• /
• 2022

Recently, object recognition using image/video signals is rapidly spreading on autonomous driving and mobile phones. However, the actual input image/video signals are easily exposed to a poor illuminance environment. A recent researches for improving illumination enable to estimate and compensate the illumination parameters. In this study, we propose VE-DCE (video enhancement zero-reference deep curve estimation) to improve the illumination of low-light images. The proposed VE-DCE uses unsupervised learning-based zero-reference deep curve, which is one of the latest among learning based estimation techniques. Experimental results show that the proposed method can achieve the quality of low-light video as well as images compared to the previous method. In addition, it can reduce the computational complexity with respect to the existing method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.12
• /
• pp.1284-1289
• /
• 2014

In this Paper, outdoor position estimation system was implemented using GPS (Global Positioning System) and INS (Inertial Navigation System). GPS position information has lots of errors by interference from obstacles and weather, the surrounding environment. To reduce these errors, multiple GPS system is used. Also, the Discrete Wavelet Transforms was applied to INS data for compensation of its error. In this paper, position estimation of the mobile robot in the straight line is conducted by EKF (Extended Kalman Filter). However, curve running position estimation is less accurate than straight line due to phase change in rotation. The curve is recognized through the rate of change in heading angle and the position estimation precision of the initial curve was improved by UPF (Unscented Particle Filter). In the case of UPF, if the number of particle is so many that big memory gets size is needed and processing speed becomes late. So, it only used the position estimation in the initial curve. Thereafter, the position of mobile robot in curve is estimated through switching from UPF to EKF again. Through the experiments, we verify the superiority of the system and make a conclusion.