• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.357-361
• /
• 1998

A new current controlled PWM technique for a 3-level inverter has been proposed and described in the paper. The proposed current control has the simple structure without needing to calculate the switching angles of the voltage vectors. The output in the proposed inverter contains less harmonic content than that of a conventional current controlled PWM controller, since the current control can be applied to the 3-level inverter. In addition, the proposed current controlled PWM technique has lower switching frequency than that of a conventional current controlled PWM technique at the same current limit. The control method and the performance for a proposed 3-level inverter has been discussed and investigated by the computer simulation.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.328-332
• /
• 1996

Current controlled inverter is the device which gives fast and accurate current output response for current command Existing current controlled inverters have no way but to take a narrow bandwidth due to resonance of output filter. In this paper, High performance current controlled inverter with multiloop structure is designed and modeling is executed in that basis. This paper realizes the high performance current controlled inverter with the bandwidth above resonant frequency, controls proposed inverter by analog controller, analyzes the performances through simulation and tests 2kW prototype system.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.28B no.12
• /
• pp.38-50
• /
• 1991

A current-controlled scheme of pulse width modulation voltage source inverter (PWM VSI) has attracted considerable attention due to its fast response with current limit and especially suitable for potentially high performance applications such as AC motor drives and UPS systems. These features yield near-sinusoidal currents in the load with reduced current peaks, lower inverter switching frequency and reduce inverter and load stresses. A high performance current-controlled inverter must have a quick response in transient state and low harmonic current in steady state. This paper compares and shows the controlled-characteristics with hysteresis controller(HC), ramp comparison controller(RCC) and predictive controller(PC) of PWM inverter to control actual current of VSI-IM.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.9
• /
• pp.1031-1041
• /
• 1992

Existing current-controlled inverters with hysteresis controller (HC) result in the dependence of the inverter on its load characteristics, poor inverter utilization due to too much or too little supply voltage, and the current error in the hysteresis band(HB) which causes deterioration of operation of the supplied motor. In this paper, techniques and results of modeling the operation of current-controlled three phase power inverter with HC are presented. Four symmetrical control schemes are considered: the so called three independent control, three semi-dependent control(a), three semi-dependent control(b) and three dependent control each using three current controller. The dependence of the inverter on its load has been studied. To overcome this difficulty, an inner feedback control has been introduced and optimum parameter has been determined. With the addition of an inner feedback control, adjustment of the switching frequency to a desired value is possible. Also, this modification improves operating characteristics of inverter by enforcing a switching pattern of low dependence on the load, resulting in significantly improved quality of the output current.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.63-69
• /
• 1998

A new current controlled PWM technique with NPC structure is proposed in this paper. A current controlled PWM technique with neutral-point-clamped pulse-width modulation inverter composed of main switching devices which operates as switch for PWM and auxiliary switching devices to clamp the output terminal potential to the neutral point potential is described. The proposed current controller has a first and second current band. The switching pattern will be made by the first current band. According to the second current band, the output state of the switching pattern is changed into positive and negative state. This inverter output contains less harmonic content and lower switching frequency than that of conventional current controlled PWM technique at the same current limit. Two inverters are compared analytically and the performance is investigated by the computer simulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.238-242
• /
• 2004

The paper describes an automatic frequency control current-fed inverter for forging applications. The IGBT in series with diodes as its switching devices in the inverter circuit which is of full-bridge type. The operating frequency is automatically tracked to maintain a small constant leading phase angle when load parameters change. The load voltage is controlled to protect the switches. The output power can be adjusted by varying the input current from phase controlled rectifiers which is a part of current source. The system has been operated at 15-17 kHz. The output power transferred to the load is 1,595 watts. It can heat the steel work pieces with 15 mm diameter and 120 mm long from room temperature to approximately 1100 $^{\circ}C$ within 20 seconds with 0.97 leading power factor on the input side.

• Journal of information and communication convergence engineering
• /
• v.8 no.1
• /
• pp.103-106
• /
• 2010

In this paper, the delay times were evaluated to develop highly reliable time-to-digital converter(TDC) in analog and digital delay element structures. The delay element can be designed by using current source or inverter. In case of using inverter, the number of inverter has to be controlled to adjust the delay time. And in case of using current source, the current for charging and discharging is controlled. When the current source is used the delay time of the delay element is not sensitive with varying the channel width of CMOS. However, when the inverter is used the delay time is directly related to the channel width of CMOS. Therefore to obtain good reliability in TDC circuit the delay element using current source is more stable compared to inverter in the viewpoint of the variation of fabrication process.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.109-112
• /
• 1998

A step down chopper and PWM current source inverter is used for the connection between the PV array and the utility. This paper proposes chopper is controlled for the dc reactor decrease and PWM current source inverter is controlled to keep the output power at the maximum point for the PV. The PV current only is measured and employed for the power calculation combining the control parameter of the PWM current source inverter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.2 no.3
• /
• pp.51-57
• /
• 1997

A new current controlled PWM technique with N.P.C structure is proposed in this paper. A current controlled PWM technique with neutral-point-clamped pulsewidth modulation inverter composed of main switching devices which operates as switches for PWM and auxiliary switching devices to clamp the output terminal potential to the neutral point potential is described. This inverter output contains less harmonic content as compared with that of a conventional current controlled PWM type. In addition, the proposed current controlled PWM technique has lower switching frequency than that of conventional current controlled PWM technique at the same current limit. Two inverters are compared analytically. The improved voltage waveform of current controlled PWM with N.P.C structure is analyzed and the performance is investigated by the computer simulation.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.277-280
• /
• 1988

In the current-controlled PWM, the actual current tracks the sinusoidal reference wave within desired hyeteresis band. This paper au99e61s the current control scheme for voltage-fed single-phase inverter and presents the simulation results. It is expected that the inverter with this control method produces no significant lower-order harmonics.