• Journal of the Korean Society of Tobacco Science
• /
• v.24 no.2
• /
• pp.75-81
• /
• 2002

This study was performed to investigate the influence of curing conditions on the composition of essential oil during curing process of burley tobacco leaves. The curing conditions were the primed curing in vinyl house (house-curing), air-curing barn (air-curing) and stalk-curing in conventional curing house (stalk-curing). Total 90 compounds are identified from the steam volatile oils of harvest and cured tobacco leaves by GC and GC-MS, respectively. The major components were neophytadiene, hexadecanoic acid, 3,8,13-duvatriene-1,5-diols, oxide-9-methylene-3,13-duvadienols, solanone, megastigma-4,6,8-trien-3-ones, phenylacetaldehyde, $\beta$-phenylethyl alcohol, indole, dihydroactinidiolide and phytol. The amount of alcoholic compounds was decreased more than approximately 50% in cured leaves without regard to the curing conditions. $\beta$-Phenylethyl alcohol and 3,8,13-duvatriene-1,5-diols were decreased more in air curing and stalk curing than in house curing. The amounts of phenylacetaldehyde, solanone, $\beta$-damascone, $\beta$ -damascenone, oxysolanone and megastigma-4,6,8-trien-3-ones as ketonic compounds, dihydroactinidiolide and indole as miscellaneous compounds in air-cured and stalk-cured tobacco leaves were 2 times higher than those in house-cured leaves, while esteric and acidic compounds were not changed largely in content by curing conditions.

• Journal of the Korean Society of Tobacco Science
• /
• v.19 no.1
• /
• pp.29-32
• /
• 1997

This study was carried out to develop a new stalk curing of the horizontal hanging method that would reduce the harvesting and curing labor, and improve its quality of cured leaf than the conventional stalk curing method in burley tobacco. The horizontal hanging stalk-curing method designed from 1988 was compared with the conventional method. The horizontal method shortened the curing Period for 7 days and reduced to 0.3%, while it occurred 9.4% in the vertical method. In the horizontal method, the quality of cured leaf improved 9%, but the contents of chemical components and physical properties were similar to those of vertical method. The labor of stalk-cut and loading in curing facility reduced 28% by the horizontal method. In harvesting and curing process, the horizontal method resulted 12% of labor saving as compared with the vertical method. Key words : horizontal hanging stalk-curing method, vertical method, stalk-curing.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.8
• /
• pp.653-658
• /
• 2014

Roll-to-Roll printing process has become a great issue as a breakthrough for low cost and mass production of electronic devices such as organic thin film transistor, and etc. To print the electronic devices, multi-layer printing is essential, and high precision register control is required for this process. Unlike stop-and-repeat printing process, it is impossible to control the register in a static state since the roll-to-roll process is a continuous system. Therefore, the behavior of web such as polyethylene terephthalate (PET) and polyimide (PI) by the tensile and thermal stress generated in the roll-to-roll process as well as motor control of driven rolls has to be considered for a high precision register control. In this study, the correlation between curing temperature and thermal deformation of PET web is analyzed. Finally, it is verified experimentally that the temperature disturbance generates the more serious register error under the higher curing temperature.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.183-188
• /
• 2009

RFID method is a non-contact automatic identification technology, which attaches microchips and antennas to an object in a tag form, to send and process information sent to the network using wireless frequency. Drying and curing process is extremely important which minimizes the resistivity of RFID antennas. This research is about the drying characteristic of conductivity ink, and analyzes and compares the hot-air drying process and infrared drying process. Also, the research was done for the improvement in drying performance by using combined process of hot-air and infrared mechanism. The experiment result shows that the hot-air or infrared drying system used alone cannot meet the required performance in drying printing method using conductivity ink. The combined drying system of hot-air and infrared ray showed resistance low enough in short drying and curing time, and this mechanism makes drying and curing process for mass and continuous production possible on-line.

• Journal of the Korean Society of Safety
• /
• v.38 no.2
• /
• pp.23-29
• /
• 2023

This study analyzed the fire status of a rubber product manufacturing factory based on 19 years of fire data. Through the analysis of the current state of fire, electrical fires accounted for 58.19%, and among electrical fires, motor fires were the highest at 26.21%. For the motor fire occurrence process, the curing process accounted for the highest rate of 51.9%. Therefore, the installation environment was investigated for the motor in the curing process, and it was confirmed that the motor's maximum ambient temperature exceeded 40℃. In particular, in the case of the motor for curing operation, the motor was installed in a separate motor room, so the average indoor temperature was 48.10℃ and the motor frame's maximum temperature was 72.80℃. In this study, the risk of motor fire was confirmed through a field survey, and a safety management plan was derived by finding a process with high fire risk and conducting an experiment on the motor's installation environment and electrical characteristics in that process.

• Restorative Dentistry and Endodontics
• /
• v.21 no.1
• /
• pp.360-365
• /
• 1996

The purpose of this study was to evaluate the changes in the degree of conversion on a composite resin surface following heat treatment and mylar strip finishing. The effects of the time interval between the light-curing and heat-curing process were also evaluated. The composite resin surface which had been covered with a coverglass showed a lower conversion rate than the surface from which a layer of $500{\mu}m$ was ground away. The composite resin surface was definitely affected by oxygen during the heat curing process when it had not been insulated. When the composite resins were heat cured after 3 days of storage following the light curing process, the increased in the degree of conversion through heatcuring was limited.

• Journal of the Korean Society of Tobacco Science
• /
• v.22 no.2
• /
• pp.133-137
• /
• 2000

The bulk curing experiment to improve the quality of flue-cured leaves were carried out to evaluate relationship between the modified(3 step-up) drying and conventional drying method in bulk curing process. Modified drying method was somewhat higher values in yellowing color index of cured leaves, and less brittle than those in conventional drying program. As to the chemical properties, there was no difference in chemical component levels in cured leaves between the modified and the conventional methods, while the major chemical compounds in relation to aromatic essential oil of cured leaves showed mostly higher level in the modified method than that in conventional drying method. Additionally 3 step-up drying method increased the tobacco quality by 2 % in price per kg compared with conventional drying method.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.3
• /
• pp.961-963
• /
• 2011

Spin-coated waterborne polyurethane to protect glass surface from environmental attacks was cured by using microwave heating. The effect of microwave heating on the reaction kinetics, chemical durability, and transmittance of polyurethane was investigated. In comparison to the conventional heating the results show that the microwave heating substantially accelerates the curing process of waterborne polyurethane and the total time for the completion of the reaction is only 1/7 of that in the conventional process. The microwave cured sample showed an excellent caustic resistance compared to conventional cured one. It means that microwave heating produces dense structure during curing process. The dense structure does not affect to the transmittance in the visible region.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.4
• /
• pp.24-32
• /
• 2008

We made a new propellant formulation to improve the productivity of Base Bleed Unit(aka BBU) by reducing of the curing time. We made an experiment with new propellant formulation such as binder characteristics and manufacturing process. In addition, we already tested several basic characteristics and the final performance of the new propellant. According to the test report, it was not only satisfied with all requirements in the specification, but it also contributed to improve productivity and reduced 53% of the curing time.

• Journal of the Korean Society of Tobacco Science
• /
• v.21 no.2
• /
• pp.182-187
• /
• 1999

A bulk curing experiment was carried out to evaluate the effect of air flow reduction in the bulk barn from color fixing stage in the chemical properties of cured leaves, The air flow was controlled by reducing air velocity of a blower from 0.3m/sec to 0.2m/sec using a boltage regulator(Slidac). The bulk curing before color fixing stage was processed in the conventional curing method. Reduction of air circulation in bulk barn did not affected so much on change of the contents of the main chemical components in cured leaved, such as nicotine, total sugar, total nitrogen, petroleum ether extract, and organic acids. Only a slight increase in essential oil contents, such as solanone, damascenone, damascone, $\beta$-ionone, and megastigmatrienone isomer, could be observed in leaves cured in the reduced air flow.