• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.310.2-310.2
• /
• 2013

For enhancement of dye-sensitized solar cell performance, TiO2 blocking layer has been used to prevent recombination between electron and hole at the conducting oxide and electrolyte interface. In solid state dye-sensitized solar cells, it is necessary to fabricate pin-hole free TiO2 blocking layer. In this work, we deposited the TiO2 blocking layer on conducting oxide by atomic layer deposition and compared the efficiency. To compare the efficiency, we fabricate solid state dye-sensitized solar cell with using CuSCN as hole transport material. We see the efficiency improve with 40nm TiO2 blocking layer and the TiO2 blocking layer morphology was characterized by SEM. Also, we used this blocking layer in TiO2/Sb2S3/ CuSCN solar cell.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1625-1627
• /
• 2000

Cu(InGa)$Se_2$(CIGS) thin film absorbers with various Cu/(In+Ga) atomic ratios were prepared by a three-stage process using a co-evaporation appartus. The effect of Na on the structural and electrical properties of CIGS films were studied and their effects on the CIGS/Mo thin film solar cells were investigated. Soda-lime glass and Corning glass were used as substrates to compare the effect of Na diffusion into CIGS film. The resistivity of CIGS films was not changed in the Cu-poor lesion due to diffusion of Na from soda-lime glass but was mainly determined by the surface resistivity controlled by excess Na.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.688-688
• /
• 2013

Al-doped ZnO (AZO) thin films have attracted a lot of attention as a cheap transparent conducting oxide (TCO) material that can replace the expensive Sn-doped In2O3. In particular, AZO thin films are widely used as a window layer of chalcogenide-based thin film solar cells such as Cu(In,Ga)Se2 and Cu2ZnSnS4 (CZTS). Mostly important requirements for the window layer material of the thin film solar cells are the high transparency and the low sheet resistance, because they influence the light absorption by the activelayer and the electron collection from the active layer, respectively. In this study, we prepared the AZO thin films by RF magnetron sputtering using a ZnO/Al2O3 (98：2wt%) ceramic target, and the effect of the sputtering condition such as the working pressure, RF power, and the working distance on the optical, electrical, and crystallographic properties of the AZO thin films was investigated. The AZO thin films with optimized properties were used as a window layer of CZTS thin film solar cells. The CZTS active layers were prepared by the electrochemical deposition and the subsequent sulfurization process, which is also one of the cost-effective synthetic approaches. In addition, the solar cell properties of the CZTS thin film solar cells, such as the photocurrent density-voltage (J-V) characteristics and the external quantum efficiency (EQE) were investigated.

• Journal of the Korean Magnetics Society
• /
• v.19 no.3
• /
• pp.113-119
• /
• 2009

$^{57}Fe_xCu_{1-x}O$(x = 0.0, 0.02) powders were prepared by sol-gel method and their crystallographic and magnetic hyperfine properties have been studied using X-ray diffraction and $M{\ddot{o}}ssbauer$ spectroscopy (MS). The crystal structure of the samples is found to be monoclinic without any secondary phases and their lattice parameters increase with increasing annealing temperature ($T_A$), which is attributed to an increase in oxygen-vacancy content. MS measurements at room temperature indicate that $Fe^{3+}$ ions substitute $Cu^{2+}$ sites and ferromagnetic phase grow with increasing $T_A$. Magnetic hyperfine and quadrupole interactions of $^{57}Fe_{0.02}Cu_{0.98}O$ ($T_A=500^{\circ}C$) in the antiferromagnetic state at 17 K have been studied, yielding the following results: $H_{hf}=426.94\;kOe$, ${\Delta}E_Q=-3.67\;mm/s$, I.S.=0.32 mm/s, ${\theta}=65^{\circ}$, ${\phi}=0^{\circ}$, and ${\eta}=0.6$.

• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.2
• /
• pp.77-87
• /
• 1994

Roles of fundamental and additional hardening precipitates on the changes of mechanical properties and electrical resistivity during precipitation decomposition in binary Al-Li, ternaty Al-Li-Cu and multi-Li-Cu-Mg-Zr alloys have been investigated by the detailed measurement of electrical resistivity, hardness and tensile strength and the observation of transmission electron micrographs. Peek hardness and tensile strength in multi-component Al-Li-Cu-Mg-Zr Alloy had higher than that of the other alloys and the results of measurement of hardness, strength and electrical resistivity in each alloys aged at 90 and $190^{\circ}C$, precipitation behaviors and mechanical properties in binary, ternary and multi-component Al-Li alloys were contributed to the ${\delta}^{\prime}$ precursory phase of ${\delta}^{\prime}$, $T_1$, G.P.B. zone and S' phases, repectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1093-1095
• /
• 2006

An orange-emitting phosphor for inorganic electroluminescent device has been studied. Cu and Cl were co-doped in Mn-doped ZnS for a high-performing phosphor. The effect of $Mn^{2+}-doping$ concentration as well as $Mg^{2+}-sensitizer$ addition on the luminescence characteristics has been investigated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.374.1-374.1
• /
• 2016

Copper and zinc are well known elements with antibacterial effect. So in this research, Cu and Zn (CZ) nanofibers (NFs) were fabricated by electrospinning method using polyvinylpyrrolidone (PVP) for adjusting viscosity. The CZ/PVP precursor solutions were prepared with copper sulfate pentahydrate, and zinc acetate dihydrate. Distilled water was used for solvent and PVP was used to regulate the viscosity of precursor solution. The CZ/PVP NF composites were obtained by electrospinning method using the precursor solution. The average diameter of obtained CZ/PVP NFs was determined by optical microscopy using Motic image plus 2.0 program and was found to be 490 nm. The chemical environment of the obtained CZ/PVP NF composites was investigated with X-ray photoelectron spectroscopy (XPS). After heating the obtained CZ/PVP NF composites at 353 K, the solvent was removed. The characteristic C 1s, Cu 2p, and Zn 2p core level XPS peaks were observed. After calcination the CZ/PVP NF composites at 873 K in Ar environment for 5 hrs, PVP was decomposed at this temperature and CZ NF was obtained. This was confirmed by decreasing the intensity of C 1s.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.4
• /
• pp.49-53
• /
• 2009

In order to investigate the formation behavior of hollow Cu via for MEMS packaging, we observed the microstructure of the Cu vias and measured the average thickness and the thickness deviation with variations of pulse-reverse pulse current density and electrodeposition time. With electrodeposition for 3 hours at the pulse and reverse pulse current densities of $-5\;mA/cm^2$ and $15\;mA/cm^2$, the average thickness and the thickness deviation of the Cu vias were $5\;{\mu}m$ and $0.63\;{\mu}m$, respectively. With increasing the electrodeposition time to 6 hours, it was possible to form the Cu vias, of which the average thickness and thickness variation of the Cu vias were $10\;{\mu}m$ and $1\;{\mu}m$, respectively. With increasing the pulse and reverse pulse current densities to $-10\;mA/cm^2$ and $30\;mA/cm^2$, Cu vias of uniform thickness could not be formed due to the faster increase of the thickness deviation than that of the average thickness with increasing the electrodeposition time.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.23 no.3
• /
• pp.179-186
• /
• 2003

This pot experiment was conducted to find out the effects of boron application( $B_{0}$ ) ; control, B$_1$; 0.2, $B_2$; 2.0, $B_3$; 6.0, $B_4$; 15.0 boron me/pot) on the forage performance of pure and mixed cultures of orchardgrass and white clover. The fourth part was concerned with the changes in the contents of B, Fe, Mn, Cu, and Zn in forages. The results obtained are summarized as follows: 1. The boron(B) contents of both forages and their differences among the B treatments generally decreased according to the cutting order. The B contents of white clover were somewhat lower in the $B_{0}$ than in the $B_2$. However, the differences in the yields between $B_{0}$ and $B_2$ were relatively great. It was probably caused by the latent B-deficiency in the $B_{0}$. Compared with white clover, the B contents of orchardgrass had relatively great differences between the $B_{0}$ and B$_2$, but both yields tended to be similar. 2. The contents of Fe, Mn, Cu, and Zn in both forages were generally different according to the forage species, whether it was a pure or mixed cultures, and additional fertilization. The effects of B application on their contents were different according to the micronutrients and above factors. 3. The Fe contents of white clover were lower in the $B_{0}$ and $B_4$ than in the$ B_2$. It tended to be related to the weak growth of roots and low yields in the $B_{0}$ and $B_2$. However, there were not consistent in the changes of contents of Mn, Cu, and Zn by the rates of B application. 4. The effects of B application on the total ion concentrations of Fe, Mn, Cu, and Zn were not consistent in both forages. However, the concentrations were generally affected by the changes in the contents of Mn and Zn. The concentrations of white clover were higher in a pure than in mixed culture.

• Journal of the Korean Chemical Society
• /
• v.47 no.4
• /
• pp.315-324
• /
• 2003

In this study, a new method is presented to produce stable hydrophobic metal alloy nanocluster in chloroform solution including surfactant NaAOT(sodium bis(2-ethylhexyl)-sulfosuccinate) via the chemical reduction of metal salt $(HAuCl_4,\AgNO_3,\Cu(NO_3)_2)$ by sodium borohydride. For the alloy nanocluster, several samples were prepared by changing the molar ratio of Au/Cu, Au/Ag alloy nanocluster, 3:1, 1:1, 1:3. The alloy nanoclusters were characterized by UV-Visible spectrophotometer, TEM(Transmission Electron Microscope), and XPS(X-ray Photoelectron Spectrometer). With the change of the mole ratio of the alloy component, the wavelengths of the surface plasmon absorption shift linearly from 520 nm of the pure Au nanocluster to 570 nm of the pure Cu nanocluster for Au/Cu alloy nanoclusters and from 405 nm to 520 nm for Au/Ag alloy nanoclusters. The chemical shifts of the Au4f, Ag3d, Cu2p XPS peaks were observed with changing the molar ratio of the alloy element. The alloy nanoclusters in chloroform solution were made uniformly in size and colloidally stable for long periods of time. These results indicate that the method here is a very effective method for synthesizing hydrophobic alloy nanoclusters with uniform or nearly uniform particle size distribution.