• Carbon letters
• /
• 제14권2호
• /
• pp.117-120
• /
• 2013

In this study, an electro-catalyst of Pt nanoparticles supported by polypyrrole-functionalized graphene (Pt/PPy-reduced graphene oxide [RGO]) is reported. The Pt nanoparticles are deposited on the PPy-RGO composite by chemical reduction of H2PtCl6 using NaBH4. The presence of graphene (RGO) caused higher activity. This might have been due to increased electro-chemically accessible surface areas, increased electronic conductivity, and easier charge-transfer at polymer-electrolyte interfaces, allowing higher dispersion and utilization of the deposited Pt nano-particles. Microstructure, morphology and crystallinity of the synthesized materials were investigated using X-ray diffraction and transmission electron microscopy. The results showed successful deposition of Pt nano-particles, with crystallite size of about 2.7 nm, on the PPy-RGO support film. Catalytic activity for methanol electro-oxidation in fuel cells was investigated using cyclic voltammetry. The fundamental electrochemical test results indicated that the electro-catalytic activity, for methanol oxidation, of the Pt/PPy-RGO combination was much better than for commercial catalyst.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.165-169
• /
• 2001

Carbon nitride films were grown on Si (100) substrate by a laser-electric discharge method with and without a magnetic field assistance. The magnetic field leads to vapor plume plasma expending upon the ambient arc discharge plasma area. Influence of the magnetic field has resulted in increase of a crystallite size in the films due to bombardment (heating) of Si substrates by energetic carbon and nitrogen species generated during cyclotron motion of electrons in the discharge zone. Many crystalline grains were observed in the morphology of the deposited films by scanning electron microscopy. In order to determine the structural crystalline parameters, X-ray diffraction (XRD) was used to analysis the grown films.

• 한국세라믹학회지
• /
• 제47권6호
• /
• pp.479-484
• /
• 2010

Microstructural and mechanical properties of the TiN films deposited on Si substrates under various substrate bias voltages by a reactive magnetron sputtering have been studied. It was found that the crystallographic texture, microstructural morphology and mechanical property of the TiN films were strongly depended on the substrate bias voltage. TiN films deposited without bias exhibited a mixed (200)-(111) texture with a strong (200) texture, which subsequently changed to a strong (111) texture with increasing bias voltage. It is also observed that the crystallite size decreases with increasing bias voltage, which corresponds to the increasing diffraction peak width of XRD patterns. The average surface roughness was calculated from AFM images of the films; these results indicated that the average surface roughness was increased with an increase in the bias voltage of the coatings.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제9권2호
• /
• pp.117-123
• /
• 2009

$Pb_{x}Cd_{1-x}S$ films are prepared in the composition range of 0.05${\leq}x{\leq}$0.25, using a chemical bath deposition growth technique under optimum conditions amide at realizing good photo response. The x-ray diffraction results show that the films are of PbS-CdS composite with individual CdS and PbS planes. The films exhibit two direct band gaps, 2.4 eV attributed to CdS, while the other varies continuously from 2.4 eV to 1.3 eV. The films surface morphology is smooth with crystallite, whose grain size increases with increasing mole fraction (x). The decrease in band gap with increase in lead concentration suggests inter-metallic compound of PbS (Eg=0.41 eV) with CdS (Eg=2.4 eV)

• 한국전기전자재료학회논문지
• /
• 제15권2호
• /
• pp.184-189
• /
• 2002

Carbon nitride films were grown on Si (100) substrate by a laser-electric discharge method with/without a magnetic field assistance. The magnetic field leads to vapor plume plasma expending upon the ambient arc discharge plasma area. Influence of the magnetic field has resulted in increased of a crystallite size int he films due to bombardment (heating) of Si substrates by energetic carbon and nitrogen species generated during cyclotron motion of electrons in the discharge zone. The surface morphology of the films with a deposition time of 2 hours was studied using a scanning electron microscopy (SEM). In order to determine the structural crystalline parameters, X-ray diffraction (XRD) was used to analysis the grown films.

• 반도체디스플레이기술학회지
• /
• 제3권4호
• /
• pp.5-11
• /
• 2004

Optical properties of PET(Polyethylene terephthalate), PC(Polycarbonate), Acrylic resin and PE(Polyethylene) sheets were studied as a function of heat treating temperature of $60^{\circ}C$ to $150^{\circ}C$. By the heat treatment, optical properties of transmittance, absorbance, and reflectance showed a considerable change with different ways according to the materials. To understand the reason of optical property change, X-ray diffraction and surface morphology were also investigated. It was observed that small crystallite and pore that can cause scattering largely affect the transmittance. It was suggested that change of surface chemical bond induce the reflectance variation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1485-1487
• /
• 2000

A variety of target configurations in sputtering process have been proposed to deposit various structures of thin film alloys and compound films. In this study, we presented the comparative experimental results regarding to the characterization of properties of Cu-Ni thin films deposited by using a magnetron co-sputtering method, as a function of target configurations; one is using a single target with varying the area of Ni chips attached on the Cu target and another is using a dual-type target with two targets of Ni and Cu separated each other. Structural(d-spacing, crystal orientation, crystallite size, cross-sectional morphology) and electrical(resistivity) properties of deposited films are characterized and compared as a function of target configurations as well as deposition conditions.

• 전기전자학회논문지
• /
• 제21권3호
• /
• pp.297-308
• /
• 2017

By using electron beam evaporation under appropriate conditions, we obtained graphene intercalated sheets on Si(111) with an average crystallite size less than 11nm. The formation of such nanocrystalline graphene was found as a time-dependent function of carbon deposition at a substrate temperature of $1000^{\circ}C$. The structural and electronic properties as well as the surface morphology of such produced materials have been confirmed by reflection high energy electron diffraction, Auger electron spectroscopy, X-ray photoemission spectroscopy, Raman spectroscopy, scanning electron microscopy, atomic force microscopy and scanning tunneling microscopy.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.668-669
• /
• 2006

The influence of $Eu^{3+}$ doping on the structural and morphological properties of the $Gd_2O_3:Eu^{3+}$ phosphor system, obtained ultrasonically via Spray Pyrolysis from common gadolinium and europium nitrate solutions, was studied. The particle morphology, crystalline and chemical structure were studied by XRD, SEM and EDS. TEM was applied in order to identify the structure and growth of "primary nanoparticles" and determine the presence of domains locally affected by "Moires Frames" and "Crystallite Size". The SADP allows determining the presence of a polycrystalline material with two phases in the "as-prepared" samples, and only an Ia3 phase along the thermal treatment.

• 한국재료학회지
• /
• 제26권10호
• /
• pp.570-576
• /
• 2016

Using the ultrasonic pyrolysis method, spherical $SiO_2$ powders were synthesized from aqueous $SiO_2$ sol as a starting material. The effects of pyrolysis conditions such as reaction temperature, $SiO_2$ sol concentration, and physical properties of precursor were investigated for the morphologies of the resulting $SiO_2$ powders. The particle size, shape, and crystallite size of the synthesized $SiO_2$ powders were demonstrated according to the pyrolysis conditions. Generally, the synthesized $SiO_2$ particles were amorphous phase and showed spherical morphology with a smooth surface. It was revealed that increased crystallite size and decreased spherical $SiO_2$ particle size were obtained with increases of the pyrolysis reaction temperature. Also, quantity of spherical $SiO_2$ particles decreased with the decrease in the concentration and surface tension of the precursor.