• The Korean Journal of Ceramics
• /
• v.2 no.4
• /
• pp.251-256
• /
• 1996

Effect of mixed grinding with a planetary ball mill of starting materials before heat treatment on the crystal structure and superconduction properties in the YBaCu composite oxide was studied. The size reduction of powders too place in the early stage of grinding, followed by aggregation of the resultant fine particles. The uniformity of the composition in the mixture was improved with grinding, which later decreased in the crystal grain size and well distribution of twin phase in the sintered bodies. The critical current density of the sintered bodies obtained from the mixture ground for 60 minutes showed the maximum value about 150 A/$\textrm{cm}^2$, while critical temperatures were around 90K and were independent of the grinding time.

• 한국데이터정보과학회:학술대회논문집
• /
• 2003.10a
• /
• pp.171-176
• /
• 2003

전기 설비의 가속 수명시험에서 절연재료의 열 수명 시험자료에 대한 통계적 분석지침으로 1987년 ANSI/IEEE Std. 101이 제정된 이래, 많은 실험의 결과 분석에 이용되어져 오고 있다. 그러나, ANSI/IEEE Std. 101 에서는 제한된 환경 하에서 얻어지는 소수의 자료를 분석에 이용하고 있어, 분석 결과의 정확성에 의문이 제기되고 있다. 본 논문에서는, ANSI/IEEE Std. 101에서 사용한 자료에서 얻은 통계량들을 근거로 Monte Carlo Simulation을 실시하여 분석지침에서 제시한 결과와 비교하여 보았다.

• Korean Journal of Materials Research
• /
• v.15 no.3
• /
• pp.166-171
• /
• 2005

Fe-6Al-9Si(N) alloy powders were synthesized by hybrid process of chemical nitrification and mechanical milling. The nitriding treatment on Fe-6Al-9Si alloy powders formed $\gamma'-Fe_4N$ phase on the powders surface. The nitriding-treated powders were pulverized by horizontal high-energy ball milling machine. The longer ball milling time tended to reduce the size of alloy powders. In ball milling for 36h, extremely fine powders with about $7\~9wt\%$ nitrogen were obtained. Through X-ray diffraction analysis on the powders, it was found out that the longer milling time caused a disappearance of the crystallinity of $\alpha-Fe$ in the powders. TEM study confirmed that the powders is comprised of a few tens nano-meter sized crystals, including $\alpha-Fe$ phase with partially $\gamma'-Fe_4N$ phase. Hysteresis curves of the synthesized powders measured by VSM revealed lower saturation magnetization and higher coercivity, which seemed to be attributed to nitrogen-impregnation and severe residual stress developed during the high energy milling. Microstructure observation on the powder annealed at 873 K for 1 h showed 10 to 20 nm sized $\alpha-Fe$ crystal. Such a enhanced crystallinity significantly increased the magnetization and decreased the coercivity, which was attributed to not only the crystallinity but also residual stress relaxation.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.4
• /
• pp.436-442
• /
• 2014

$LaCoO_3$ powders synthesized by Pechini process were pulverized by planetary ball-milling to decrease particle size and characterized as a catalyst in alkaline solution for oxygen reduction and evolution reaction (ORR & OER). The changes of physical properties, such as particle size distribution, surface area and electric conductivity, were analyzed as a function of ball-milling time. Also, the variations of the crystal structure and surface morphology of ball-milled powders were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The electrochemically catalytic activities of the intrinsic $LaCoO_3$ powders decreased with increasing ball-milling time, but their electrochemical performance as an electrode improved by the increase of the surface area of the powder.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.5
• /
• pp.505-512
• /
• 2023

This study investigated crystal structures, microstructures, and electric-field-induced strain (EFIS) properties of Bi-based lead-free ferroelectric/relaxor composites. Bi_1/2Na_0.82K_0.18)_1/2TiO₃ (BNKT) as a ferroelectric material and 0.78Bi_1/2(Na_0.78K_0.22)_1/2TiO₃-0.02LaFeO₃ (BNKT2LF) as a relaxor material were synthesized using a conventional solid-state reaction method, and the resulting BNKT2LF powders were subjected to high-energy ball milling (HEBM) after calcination. As a result, HEBM proved a larger average grain size of sintered samples compared to conventional ball milling (CBM). In addition, the increased sintering time led to grain growth. Furthermore, HEBM treatment and sintering time demonstrated a significant effect on EFIS of BNKT/BNKT2LF composites. At 6 kV/mm, 0.35% of the maximum strain (S_max) was observed in the HEBM sample sintered for 12 h. The unipolar strain curves of CBM samples were almost linear, indicating almost no phase transitions, while HEBM samples displayed phase transitions at 5~6 kV/mm for all sintering time levels, showing the highest S_max/E_max value of 700 pm/V. These results indicated that HEBM treatment with a long sintering time might significantly enhance the electromechanical strain properties of BNT-based ceramics.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.1
• /
• pp.36-40
• /
• 2003

The diamond-like nanocomposite (DLN) thin films were deposited on Si substrates using $CH_4/(C_2H_5O)_4Si/H_2$/Ar gas mixtures as source gases by the plasma enhanced chemical vapor deposition (PECVD). The chemical structure and microstructure of grown films were investigated and their tribological properties were evaluated by a ball-on-plate type tribometer. The deposited DLN films mainly consisted of diamond-like a-C:H and quartz-like a-Si:O networks. The DLN films had a good agreement with tribological coating applications due to their extremely low friction coefficients and low wear rates.

• Transactions of Materials Processing
• /
• v.19 no.6
• /
• pp.357-362
• /
• 2010

Dry sliding wear behavior of pure Fe and Cu which have BCC and FCC crystal structure, respectively, was investigated. The wear characteristics of the pure metals with different crystal structure were compared. Dry sliding wear tests were carried out using a pin-on-disk wear tester at various loads under the constant sliding speed condition of 0.15 m/s against a silica ball at room temperature. Sliding distance was fixed as 600 m for all wear tests. Wear rate of a specimen was calculated by dividing the weight loss of the specimen after the test by the specific gravity and sliding distance. Worn surfaces and wear debris were analyzed by SEM. The wear of both pure Fe and Cu proceeded with surface deformation, resulting in similar wear rates despite of their structure difference under the current test conditions. Wear rates of both metals were low if the surface deformation due to wear forms thick surface-deformation layer that is strain hardened beneath the wearing surface. The pure Cu specimens showed a lot of oxides on the worn surface when tested at low loads less than 5 N, which resulted in very low wear rate.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.3
• /
• pp.135-142
• /
• 2017

In this study, we prepared the board of vermiculite materials utilizing coal bottom ash from the Western thermal power stations in Korea and obtained experimental data in applications for building interior materials with the characteristics of sound absorption. To produce the mixture materials of vermiculite and coal bottom ash, we used a microwave drying process. In addition, a ball milling process was used to produce particles of coal bottom ash with a uniform size of $65{\mu}m$. When the board made from mixture materials of vermiculite and coal bottom ash were produced with bottom ash sulfur concentrations of 5, 10 wt%, maximum bending loads were analyzed. These experimental results would contribute much to fundamental data essential to the recycling technology of coal bottom ash.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.1
• /
• pp.11-15
• /
• 2007

Stable metallic Cu/Zn nanoparticles were prepared in the base oil phase by hydrothermal method. The physical properties, such as crystal structure, crystallite size and crystallinity according to synthesis conditions have been investigated by XRD, FT-IR and TEM. In addition, 4-ball test has been performed in order to investigate the frictional wear properties of prepared nanosized Cu/Zn particles. The peaks of the X-ray diffraction pattern indicate that the particle size was very small and crystallinity of Cu/Zn particles was good. The micrographs of TEM showed that nanosized Cu/Zn particles possessed a spherical morphology with a narrow size distribution. The crystallite size of the Cu/Zn particles synthesized in base oils was 23-30 nm. It was found that the antiwear capacity increases with increasing Cu/Zn concentration. When the concentration of Cu/Zn was 5.0 wt%, the wear scar diameters was 0.38 mm.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.1
• /
• pp.132-136
• /
• 1999

Mechanical alloying (MA) by ball mill of $Fe_{30}Cr_{70}$ elemental powders was carried out under the nitrogen gas atmosphere. Amorphization has been observed in this case, while MA under an inert argon gas atmosphere produces the bcc solid solution. The DSC spectrum for the mechanically alloyed $(Fe_{30}Cr_{70})_{0.85}N_{0.15)$powders exhibits a sharp exothermic peak due to crystallization at about $550^{\circ}C$. Structural transformation from the bcc crystalline to amorphous states was observed through X-ray and neutron diffractions. During amorphization process the octahedral unit, which is typical of a polyhedron formed in any crystal structures, was preferentially destroyed and transformed into the tetrahedral unit. Futhermore, neutron diffraction measurements revealed that a nitrogen atom is situated at a center of the tetrahedron formed by metal atoms.