• Steel and Composite Structures
• /
• 제15권1호
• /
• pp.41-55
• /
• 2013

This paper presents a numerical study of axially loaded concrete-filled steel tubular columns with "T" shaped cross section (CFTTS) based on the ABAQUS standard solver. Two types of columns with "T" shaped cross section, the common concrete-filled steel tubular columns with "T" shaped cross section (CCFTTS) and the double concrete-filled steel tubular columns with "T" shaped cross section (DCFTTS), are discussed. The failure modes, confining effects and load-displacement curves are analyzed. The numerical results indicate that both have the similar failure mode that the steel tubes are only outward buckling on all columns' faces. It is found that DCFTTS columns have higher axial capacities than CCFTTS ones duo to the steel tube of DCFTTS columns can plays more significant confining effect on concrete. A parametric study, including influence of tube thickness, concrete strength and friction coefficient of tube-concrete interface on the axial capacities is also carried out. Simplified formulae were also proposed based on this study.

• Journal of the Korean Physical Society
• /
• 제73권10호
• /
• pp.1486-1494
• /
• 2018

Based on the semiclassical theory of chaotic scattering, Tanner et al. [J. Phys. B 40, F157 (2007)] proposed the fluctuation in the partial photoionization cross section of helium below the double-ionization threshold would show the same characteristics as in the total cross section, predicting that the Fourier spectrum of the fluctuation reveals peaks at the classical actions of closed triple collision orbits and the amplitude of the fluctuation decreases algebraically as the energy approaches the double-ionization threshold. In that paper, however, the predictions were not clearly confirmed due to the lack of experimental data with sufficient accuracy. So instead, we calculate the partial photoionization cross sections of collinear eZe helium for the energy range from the single-ionization threshold $I_{20}$ to $I_{32}$ in order to numerically confirm the predictions. Analysis of the fluctuation in the partial cross section shows that the predictions are indeed valid. Our findings mean that the fluctuation in the partial photoionization cross section can be described by classical triple collision orbits in the semiclassical limit. Thus it explains in a natural way the mirroring and mimicking structures observed in cross section signals for different ionization channels.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.348-353
• /
• 2008

A vibration analysis for a rotating cantilever beam with the tapered cross section is presented in this study. The stiffness changes due to the stretching caused by centrifugal inertia forces when a tapered cantilever beam rotates about the axis perpendicular to its longitudinal axis. When the cross section of cantilever beam are assumed to decrease constantly, the mass and stiffness also change according to the variation of the thickness and width ratio of a tapered cantilever beam. Such phenomena result in variations of natural frequencies and mode shapes. Therefore it is important to the equations of motion in order to be obtained accurate predictions of these variations. The equations of motion of a rotating tapered cantilever beam are derived by using hybrid deformation variable modeling method and numerical results are obtained along with the angular velocity and the thickness and width ratio.

• 한국소음진동공학회논문집
• /
• 제19권4호
• /
• pp.363-369
• /
• 2009

A vibration analysis for a rotating cantilever beam with the tapered cross section is presented in this study. The stiffness changes due to the stretching caused by centrifugal inertia forces when a tapered cantilever beam rotates about the axis perpendicular to its longitudinal axis. When the cross section of cantilever beam are assumed to decrease constantly, the mass and stiffness also change according to the variation of the thickness and width ratio of a tapered cantilever beam. Such phenomena result in variations of natural frequencies and mode shapes. Therefore it is important to the equations of motion in order to be obtained accurate predictions of these variations. The equations of motion of a rotating tapered cantilever beam are derived by using hybrid deformation variable modeling method and numerical results are obtained along with the angular velocity and the thickness and width ratio.

• Smart Structures and Systems
• /
• 제13권4호
• /
• pp.659-683
• /
• 2014

The static analysis of structures with arbitrary cross-section geometry and material lamination via a refined one-dimensional (1D) approach is presented in this paper. Higher-order 1D models with a variable order of expansion for the displacement field are developed on the basis of Carrera Unified Formulation (CUF). Classical Euler-Bernoulli and Timoshenko beam theories are obtained as particular cases of the first-order model. Numerical results of displacement, strain and stress are provided by using the finite element method (FEM) along the longitudinal direction for different configurations in excellent agreement with three-dimensional (3D) finite element solutions. In particular, a layered thin-walled cylinder is considered as first assessment with a laminated conventional cross-section. An atherosclerotic plaque is introduced as a typical structure with arbitrary cross-section geometry and studied for both the homogeneous and nonhomogeneous material cases through the 1D variable kinematic models. The analyses highlight limitations of classical beam theories and the importance of higher-order terms in accurately detecting in-plane cross-section deformation without introducing additional numerical problems. Comparisons with 3D finite element solutions prove that 1D CUF provides remarkable three-dimensional accuracy in the analysis of even short and nonhomogeneous structures with arbitrary geometry through a significant reduction in computational cost.

• 대한조선학회논문집
• /
• 제45권6호
• /
• pp.695-702
• /
• 2008

In this paper, a new numerical method is proposed to analyze near-field sonar cross section of acoustically large-sized underwater targets such as submarines. A near-field problem is converted to a far-field problem using a spherical projection method with respect to the objective target. Then, sonar cross section is calculated with a physical optics well established in far-field acoustic wave scattering problems. The analysis results of a square flat plate compared with those obtained by other method show the accuracy of the proposed method. Moreover, it is noted that the sonar cross section is varied with respect to the targeting point as well as the range. Finally, numerical analysis results of real-like underwater target such as a submarine pressure hull are discussed.

• 한국의류산업학회지
• /
• 제2권3호
• /
• pp.239-245
• /
• 2000

The purpose of this study was for analysis of ease about basic bodice pattern, as the first step of the research process for the drawing method of basic bodice for women in their twenties. The five selected basic bodice were made and they were worn by FRP body The garment space of each bodice was measured by analysis of the garment space of each section in figure of polymerization of cross section by a 3-D measuring instrument. The research suggests that this compared analysis is an objective reference. This analysis not only of the area of cross section of garment space and ease but also of the girth of the body shape and wearing shape, using the PAD system and 3-D measuring instrument, can be helpful in making garment patterns.

• 소성∙가공
• /
• 제17권3호
• /
• pp.182-188
• /
• 2008

Crash box is one of the most important automotive parts for crash energy absorption and is equipped at the front end of the front side member. The specific characteristics of aluminum alloys offer the possibility to design cost-effective lightweight structures with high stiffness and excellent crash energy absorption potential. This study deals with crashworthiness of aluminum crash box for an auto-body with the various types of cross section. For aluminum alloys, A17003-T7 and A17003-T5, the dynamic tensile test was carried out to apply for crash analysis at the range of strain from 0.003/sec to 200/sec. The crash analysis and the crash test were carried out for three cross sections of rectangle, hexagon and octagon. The analysis results show that the octagon cross section shape with A17003-T5 has higher crashworthiness than other cross section shapes. The effect of rib shapes in the cross section is important factor in crash analysis. Finally, new configuration of crash box with high crash energy absorption was suggested.

• 대한조선학회지
• /
• 제17권1호
• /
• pp.11-18
• /
• 1980

In the conventional ship's structures, the stiffeners with asymmetric sections have been widely used, in spite of the disadvantage on the point of strength, compared to those with symmetric sections. So far, the stiffened plating was usually analyzed not considering the geometric unsymmetry characteristics of the section, including only the cross sectional area and moment of inertia. In this paper, the stiffened plating is devided into the strips having a thin-walled open cross section by using the concept of the effective width. The geometric characteristics of the sections are also included. The governing equations are derived, which can be applied to the arbitrary cross section beams, and the symmetric and the asymmetric section beams which have the same cross sectional areas are analyzed by using the finite element method. From that result, we obtain the allowable load of the two sections, and compared them.

• 소성∙가공
• /
• 제17권2호
• /
• pp.130-134
• /
• 2008

Resource and energy saving is a very important practice for the future as well as for today. Weight saving of structural parts, which are formed by extrusion, plays a key role in manufacturing field. The cross-sections of extruded parts with industrial aluminum are constant in the axial direction by conventional extrusion method. Especially, these aluminum parts used and manufactured in the car industry need other processes to vary the cross-section in the axial direction. However, applications of these parts are often limited by high cost. If the cross-section of the parts is variable by only extrusion with newly developed method, the application of extruded aluminum parts will actually increase. Therefore, a new CNC extruder that can control the section area of a car part was invented for the first time in the nation. Using the extrusion machine, the experiment was performed to validate its workability during the variable section extrusion process. Also, numerical analysis was carried out to investigate the flow mode with different speeds of main ram and various pocket shapes of a die-set in the variable section extrusion process.