• Membrane Journal
• /
• v.18 no.1
• /
• pp.7-25
• /
• 2008

Sodium dodecyl sulfate, which was anionic surfactant, at a concentration higher than its critical micellar concentration was added to calcium solution for forming micelles. Then aggregates were formed by adsorption or binding of calcium ions on the surface of micelles, and gathering between them, and then rejected by two kinds of ceramic membranes to remove calcium ions. As result, rejection rates of calcium were higher than 99.98%. And in our experimental range the higher TMP trended to increase the resistance of membrane fouling ($R_f$), total permeate volume ($V_T$), dimensionless permeate flux ($J/J_o$) and permeate flux (J) because TMP was driving force. And we investigated effects of $N_2$-back-flushing time and filtration time, that was back-flushing period, during periodic $N_2$-back-flushing on ceramic membranes. As result, optimal BTs for NCMT-623l ($0.07{\mu}m$ pore size) and NCMT-7231 membrane ($0.10{\mu}m$) were 10 sec and 15 sec, respectively. Also, optimal FT was 5 min for both membranes, and the frequent $N_2$-back-flushing could decrease membrane fouling effectively. Then, the optimal conditions resulting from our experiments for synthetic calcium solution were applied to groundwater using as washing process of soymilk package. As result, rejection rates of calcium were higher than 99.98%.

• Applied Chemistry for Engineering
• /
• v.22 no.1
• /
• pp.37-44
• /
• 2011

The critical micelle concentration (CMC) of sorbitan laurate SP 20 surfactant in this paper was near $7.216{\times}10^{-4}mol/L$ and the surface tension at CMC was about 26.0 mN/m, which showed higher CMC and lower surface tension than those of octylphenol ethoxylate octylphenol ethoxylate (OPE) 10 surfactant. Dynamic surface tension measurement using a maximum bubble pressure tensiometer showed that the adsorption rate at the interface between air and surfactant solution was found to be slower with SP 20 surfactant, presumably due to a low mobility of SP 20 surfactant monomer. The contact angle of SP 20 surfactant solution was observed to decrease with an increase in surfactant concentration and showed a larger value than that of OPE 10 surfactant solution. Half-life time for foams generated with 1 wt% surfactant solution was also larger with SP 20 surfactant, which indicated higher foam stability with SP 20 surfactant. Dynamic behavior study reveals that the solubilization of n-decane oil was much lower with SP 20, which is in good agreement with experimental results of foam stability, contact angle and CMC. Dynamic interfacial tension measurement by a spinning drop tensiometer shows that interfacial tensions at equilibrium condition in both systems were almost the same but the time required to reach equilibrium was longer with SP 20.

• Journal of Soil and Groundwater Environment
• /
• v.13 no.1
• /
• pp.32-42
• /
• 2008

A surfactant recovery and reuse process by selective adsorption with activated carbon was proposed to reduce surfactant cost in a soil washing process. Mathematical model simulation was performed for the whole process, which consists of soil washing, soil recovery, and soil re-washing. The optimal range of surfactant dosage was $6{\sim}10$-fold critical micelle concentration in soil. The efficiency of surfactant reuse process was decreased with increasing the dosage of activated carbon. Effectiveness factor for activated carbon significantly altered the efficiency of the reuse process unlike effectiveness factor for soil. Total requirement of surfactant was reduced to 20-30% with the reuse process compared to the conventional soil washing process. The contamination of wastewater after soil washing was reduced with the reuse process. This mathematical model can be used to estimate performance of the whole process of soil washing including surfactant recovery and to obtain optimal ranges of operating conditions without extra labor-intensive experimental works.

• Journal of Life Science
• /
• v.15 no.5 s.72
• /
• pp.679-684
• /
• 2005

The objective of this study was investigate the characteristic of biosurfactant produced from the iso-lated strain. The strain was isolated from soli samples of Duck-Yu Mountain and it was identified as Bacillus atrophaeus DYL-130 by 16S rDNA and gyrA gene nucleotide sequence analysis. The surface ten-sion of culture filtrate of Bacillus atrophaeus DYL-130 decreased to 28 mN/m and its biosurfactant con-centration was determined by diluting the culture filtrate until the critical micelle concentration (CMC). The emulsifying activity and stability of crude biosurfactant was measured by using water-immiscible hydrocarbons and oils as substrate. The biosurfactant was purified by affinity chromatography and the surface activity of purified biosurfactant was measured by drop-collapsing method and it could be effectively emulsify toluene.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.4032-4038
• /
• 2014

Vegetable fatty acid solid soap requires a drying process for moisture evaporation and hardness after being manufactured through saponification. Although the soap is manufactured by mixing additives mainly from natural ingredients, existing studies have focused primarily on the usability of vegetable solid soap. Consequently, research into the physical properties of vegetable fatty acid solid soap mixed with natural ingredients has been unsatisfactory. Therefore, this study attempted to compare and observe the changes in the physical properties (pH, surface tension, critical micelle concentration, and cleansing power) of solid soap in accordance with the drying period and additives (tea tree E.O and $TiO_2$) using pH paper, the Du Nouy measurement method, sedimentation method, and ultrasound washer. Regardless of the mixture with additives, vegetable fatty acid solid soap showed the same pH, and there was no change in the pH while maintaining pH 8 beginning from the $2^{nd}$ weeks to $12^{th}$ weeks of drying. In addition, as a result of measuring the surface tension and CMC, regardless of the drying period, only the soap added with $TiO_2$ showed an even value of 62.5mg/L, whereas the other soap specimens showed a decline in CMC to 25mg/L on the fourth week of drying. As a result of measuring the detergency, the removal efficiency of vegetable fatty acid solid soap mixed with tea tree E.O and $TiO_2$ and dried for four weeks was 4.50~4.65%, which was higher than that of the vegetable fatty acid solid soap without additives (3.62~3.92%).

• Korean Chemical Engineering Research
• /
• v.50 no.6
• /
• pp.960-968
• /
• 2012

In this study, the measurement of physical properties of 3 different ethylene oxide adducted zwitterionic surfactants were measured such as critical micelle concentration, surface tension, interfacial tension, contact angle, viscosity and foam stability. Also, the dual function characteristics of the zwitterionic surfactants were investigated by determining an isoelectric point, which were obtained using zeta potential measurement and QCM (quartz crystal microbalance) experiments. The isoelectric point of the synthesized zwitterionic surfactant determined by zeta potential measurement was close to that obtained by QCM experiment and both results have shown almost the same trend as that determined by the frictional property measured using an automated mildness tester. In particular, it has been observed that all three surfactants used during this study provide better softening effect at a pH of neutral condition than at an acidic or an alkaline condition. This result indicates that the synthesized surfactants act as a cationic surfactant at a pH of neutral condition and thus provide good softening effect during a rinsing cycle in the detergency process.

• Journal of the Korean Chemical Society
• /
• v.48 no.2
• /
• pp.195-202
• /
• 2004

Micellar catalysis is an essential part of theoretical and experimental curricular. The sodium dodecylsulfate (SDS) catalyzed reaction between glycine and potassium permanganate in acidic medium is an ideal kinetic experiment for the secondary and undergraduate physical chemistry laboratory, to show the effect of micellar catalysis on rate of the reaction. The reaction is conducted both with and without SDS to observe the rate enhancement in the presence of surfactant. To show surfactant catalysis a plot between k and [SDS] is plotted. As surfactant catalysis is observed even before the critical micelle concentration of SDS, this pre-micellar catalysis can be understood in the light of positive co-operativity. The value of positive cooperative index (n) has been found to be 2.37. Further, dependence of the reaction rate on substrate and oxidant concentrations is also discussed. The reaction follows pseudo-first-order kinetics. The overall reaction is second order, with first-order dependence on both glycine and permanganate concentrations. The theory of surfactant catalysis is also discussed. With the conditions specified in the experiment, total reaction times are in 3~4 hours lab session, thus allowing several data sets to be acquired in a single laboratory period. Preparation of solutions and procedure is also given in detail.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.537-542
• /
• 1999

Removal of sulfur compounds in the petroleum products is essential for the prevention of sulfur oxides. However, conventional methods involving catalytic reactions are found to have some limitations in complete removal of harmful sulfur compounds and to require relatively high cost. Recently, desulfurization process using microorganisms is known to be promising in terms of excellent sulfur removal efficiency and reasonably low treatment cost. For the biodesulfurization process to be effective, the solubilization of sulfur compounds into aqueous solution is a prerequisite. In this study, polyoxyethylene nonionic surfactants were used in order to enhance the solubilization of sulfur spectrophotometer. The solubilization of sulfur compounds was found to increase with temperature and to bo abruptly increased at above 1 wt % surfactant solutions. It was also observed that the longer the hydrophobic chain of the surfactant molecule, the higher solubilizing power of a nonionic surfactant. It was found that the Tergitol series surfactants showed higher solubilizing capacity than Neodol series presumably due to the disruption of the regular packing in the hydrocarbon region of the surfactant aggregates.

• Applied Chemistry for Engineering
• /
• v.20 no.1
• /
• pp.9-14
• /
• 2009

A zwitterionic surfactant shows not only detergency but also softening effect since it shows characteristics of a nonionic or an anionic surfactant above an isoelectric point, while showing characteristics of a cationic surfactant below an isoelectric point. Therefore, a zwitterionic surfactant can serve as a dual function surfactant by a single molecule through the interconversion of cleaning and softening effects depending on pH of the aqueous solution. In this study, the dual function characteristics of an amine oxide zwitterionic surfactant were investigated by measuring the zeta potential and the isoelectric point using quartz crystal microbalance (QCM). In addition, the physical properties of an amine oxide surfactant such as critical micelle concentration, surface tension, interfacial tension, contact angle and viscosity were measured and phase behavior study was also performed. The isoelectric point of an amine oxide surfactant determined by zeta potential measurement was near 7.35 and that obtained by QCM experiment was about 7.4, where both results were found to be close to the value reported in the literature.

• Applied Chemistry for Engineering
• /
• v.31 no.4
• /
• pp.429-437
• /
• 2020

In this study, a cationic gemini surfactant was synthesized using isosorbide, in order to modify the alkyl chain length in the range of C₁₀~C₁₆. The c.m.c and surface tension of the synthesized cationic gemini surfactant were measured to be in the ranges of 5.13 × 10^-4~1.62 × 10^-4 mol/L and 31.86~37.41 dyne/cm, respectively. The surface tension increased with increasing the length of the alkyl group. In addition, as the area per molecule occupied by the surfactant adsorbed on the interface increased with the reduced extent of adsorption, the bubble generation at the air-water interface decreased. The emulsifying capacity in benzene was maintained above 60 ± 5% after 8 h while that in soybean oil tended to decrease above 50 ± 5%. The performance was superior in benzene, a highly hydrophobic substance, and the emulsion stability was shown to be consistent beyond 1 h during the preparation of pre-emulsion in oil and water. The antimicrobial activity was dependent on the length of the hydrophobic chain of the synthesized cationic gemini surfactant due to the increased size of the clean zone in Escherichia coli (E.coli) and Staphylococcus aureus.