• 한국표면공학회지
• /
• 제47권5호
• /
• pp.215-220
• /
• 2014

Electrodeposition behaviors of Pd-Ni alloys were investigated from the polarization curves in a solution containing ethylenediamine as complexing agent. The microstructure and hardness of electrodeposited Pd-Ni alloys were also characterized. Codeposition of Pd-Ni alloys was successfully performed in the wide current density ranging from 2 to $5000A{\cdot}m^{-2}$ because the deposition potential of Pd became close to that of Ni in the ethylenediamine-contained solution. It was also found from X-ray diffraction patterns that the solid solution between Pd and Ni was formed with variation of the composition of alloys. The measured hardness of Pd-Ni alloys increased with increasing the contents of Ni due to solid solution strengthening and grain refinement. The electrodeposited Pd-Ni alloys also exhibited a crack free smooth surface morphology from the SEM observation.

• Journal of Industrial and Engineering Chemistry
• /
• 제68권
• /
• pp.124-128
• /
• 2018

Titanium doping is employed to enhance the structural strength of a high-Ni layered cathode material in lithium ion batteries during high temperature cycling. After Ti-doping, the external morphology remains similar, but the lattice parameters of the layered structure are slightly shifted toward larger values. With application of the prepared materials as cathodes in lithium-ion batteries, the initial capacities are similar but the cycling performance at $25^{\circ}C$ is enhanced by Ti-doping. During high temperature cycling at $60^{\circ}C$, furthermore, highly improved capacity retention is achieved with the Ti-doped material (95% of initial capacity at 50th cycles), while cycle fading is accelerated with the bare electrode. This enhancement is attributed to better retention of the compressive strength of the particles and retarded crack formation within the particles. In addition, impedance increase is reduced in the Ti-doped electrode, which is attributed to an improvement in the structural strength of the high-Ni cathode material with Ti-doping.

• 한국표면공학회지
• /
• 제50권5호
• /
• pp.411-420
• /
• 2017

In this paper, two methods of making the Pd-added $SnO_2$ ($Pd-SnO_2$) powder with pure tetragonal phase by the hydrazine method were suggested and compared in terms of crystal structure, surface morphology, and alcohol gas response. One of the addition methods is to use $PdCl_2$ as a Pd source, the other is to use Pd-based organic with oleylamine (OAM). When Pd concentration was increased from 0 to 5 wt%, the average grain size of $Pd-SnO_2$ made with Pd-OAM were decreased from 32 to 12 nm. In the case of using with $PdCl_2$, grain size of the $PdCl_2$ fell to less than 10 nm. However, agglomerated and extruded surface morphology was observed for the films with Pd addition over 4 wt%. The crack-free $Pd-SnO_2$ thick films were able to successfully fill the $30{\mu}m$ gap of patterned Pt electrodes by optimized ink dropping method. Also, the 2 wt% $Pd-SnO_2$ thick film made with PdCl2 showed gas responses ($R_{air}/R_{gas}$) of 3.7, 5.7 and 9.0 at alcohol concentrations of 10, 50 and 100 ppm, respectively. On the other hand, the prepared 3 wt% $Pd-SnO_2$ thick film with Pd-OAM exhibited very excellent responses of 3.4, 6.8 and 12.2 at the equivalent measurement conditions, respectively. The 3 wt% $Pd-SnO_2$ thick film with Pd-OAM has a specific surface area of $31.39m^2/g$.

• 한국산학기술학회논문지
• /
• 제13권10호
• /
• pp.4365-4370
• /
• 2012

MAO 법을 이용하여 전류밀도 4A/$cm^2$조건에서 3종류의 전해액과 코팅시간에 따라 AZ31 마그네슘 합금을 산화피막 처리하였다. 코팅시간이 길어짐에 따라 코팅층의 표면형상은 기공이 더욱 커지고, 표면에 균열이 발생하기도 하였다. 또한 코팅시간이 길어짐에 따라 코팅층의 두께와 경도(HV)값은 증가하였다. AZ31합금의 코팅층 상들은 MgO, $Mg_2SiO_4$ 그리고 $MgAl_2O_4$ 산화물로 이루어졌다. 산화코팅된 AZ31합금을 5% NaCl 용액에서 168시간동안 염수분무실험결과 우수한 내식성을 나타냈다.

• 한국건축시공학회지
• /
• 제15권6호
• /
• pp.579-587
• /
• 2015

자기치유성능을 가지고 있는 자기치유제를 함유하고 있는 마이크로 캡슐을 콘크리트 표면의 고분자 매트릭스층에 적용하였다. 메타크릴레이트를 코어물질로 하고 폴리 우레아포름알데히드를 캡슐막 구성물질로 하는 미세캡슐을 고분자 매트릭스 안에 첨가하여 콘크리트 표면에 코팅하였다. 콘크리트 표면에 미세균열이 형성되고 전파될 때, 균열이 전파되는 위치에 있는 캡슐이 파괴되어 치유체가 균열면 사이로 흘러나오게 되고, 균열에 스며든 단량체가 햇빛에 의해 중합반응을 일으켜 균열이 자기치유 되는 현상을 고찰한다. 자기치유성능평가는 흡수성, 투수성 실험 및 광학현미경을 통한 관찰로 확인하였다. 결과적으로 제시된 자기치유시스템은 콘크리트 균열부의 부분적인 복원을 위해 사용할 수 있음을 확인하였다.

• Journal of Welding and Joining
• /
• 제18권1호
• /
• pp.59-69
• /
• 2000

The purpose of the present study was to investigate weld metallurgical phenomena such as primary solidification mode, microstructural evolution and hot cracking susceptibility in nitrogen-bearing austenitic stainless steel GTA welds. Eight experimental heats varying nitrogen content from 0.007 to 0.23 wt.% were used in this study. Autogenous GTA welding was performed on weld coupons and the primary solidification mode and their microstructural characteristics were investigated from the fusion welds. Varestraint test was employed to evaluate the solidification cracking susceptibility of the heats and TCL(Total Crack Length) was used as cracking susceptibility index. The solidification mode shifted from primary ferrite to primary austenite with an increase in nitrogen content. Retained delta ferrite exhibited a variety of morphology as nitrogen content varied. The weld fusion zone exhibited duplex structure(austenite+ferrite) at nitrogen contents less than 0.10 wt.% but fully austenitic structure at nitrogen contents more than 0.20 wt.%. The weld fusion zone in alloys with about 0.15 wt.% nitrogen experienced primary austenite + primary ferrite solidification (mode AF) and contained delta ferrite less than 1% at room temperature. Regarding to solidification cracking susceptibility, the welds with fully austenitic structure exhibited high cracking susceptibility while those with duplex structure low susceptibility. The cracking susceptibility increased slowly with an increase in nitrogen content up to 0.20 wt.% but sharply as nitrogen content exceeded 0.20 wt.%, which was attributed to solidification mode shift fro primary ferrite to primary austenite single phase solidification.

• 한국지구과학회지
• /
• 제35권7호
• /
• pp.501-517
• /
• 2014

주상절리에 관한 최근 연구를 살펴본 결과, 우리나라에 분포하는 주상절리를 이해하고, 활용하기 위한 연구 방향은 다음과 같다; 칼러네이드와 엔테블러춰의 기하학적 형태, 형성 메커니즘과 패턴의 변화, 수평단면과 내부 구조, 주상절리 상하부의 판상절리, 전분 혼합액의 건조실험, 절리 형성에 대한 수치 모델 및 컴퓨터 그래픽 활용, 화산암의 산출 상태에 따른 주상절리 형태와 크기, 모암의 암석학적 및 광물학적 연구. 이와 더불어 지표에 노출된 후의 변질, 풍화작용의 결과로 만들어진 너덜겅, 토르, 타포니 등과 같은 2차적인 경관에 대한 기재도 필요하다. 이 연구는 우리나라 주상절리와 신생대 용암류를 해석하는 중요한 역할을 할 것이다. 또한 연구 성과는 지질관광의 활성화와 지질학습장 측면에서 활용도가 높을 것이다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제6권3호
• /
• pp.16-20
• /
• 2004

YB $a_2$C $u_3$$O_{7-x}$ (YBCO) films were deposited on (100) SrTi $O_3$ single crystal substrates by a metal organic chemical vapor deposition (MOCVD) system of hot-wall type using single liquid source. Under the condition of the mole ratio of Y(tmhd)$_3$:Ba(tmhd)$_2$:Cu(tmhd)$_2$= 1:2.1:2.9. the deposition pressure of 10 Torr. the MO source line speed of 15 cm/min. the Ar/ $O_2$ flow rate of 800/800 sccm. YBCO films were prepared at the deposition temperatures of 780∼89$0^{\circ}C$. In case of the YBCO films with 2.2 ${\mu}{\textrm}{m}$ thickness deposited for 6 minutes at 86$0^{\circ}C$. XRD pattern showed complete c-axis growth and SEM morphology showed dense and crack-free surface. The atomic ratios of Ba/Y and Cu/Ba in the film were 1.92 and 1.56. respectively. The deposition rate of the film was as high as 0.37 ${\mu}{\textrm}{m}$/min. The critical temperature ( $T_{c.zero}$) of the film was 87K. The critical current of the film was 104 A/cm-width. and the critical current density was 0.47 MA/$\textrm{cm}^2$. For the thinner film of 1.3 ${\mu}{\textrm}{m}$ thickness. the critical current density of 0.62 MA/$\textrm{cm}^2$ was obtained.d.

• 화약ㆍ발파
• /
• 제14권4호
• /
• pp.13-19
• /
• 1996

본 연구는 불연속면이 존재하는 암반에서 smooth blasting 이 실시되었을 때의 발파파단면의 형성기구를 밝히고, 효과적인 smooth blasting을 실시하기 위한 기술적 자료를 제공하기 위하여 수행되었다. 첫째, 불연속면의 경사와 발파공간거리에 의해서 형성되는 발파파단면의 형상을 I형(인접발파공이 직접 연결된 것), II형(단일 균열으로 연결된 것) 그리고 III형(방사상 균열에 의해서 형성된 것)으로 가정하고, 발파파단면의 요철도의 정도를 예측하는 방법을 제시하였다. 둘째 불연속면의 종류와 발파공에서 불연속면까지의 거리의 변화에 따른 발파균열의 상황을 검토하여 발파균열이 단일이나 방사상으로 되는 한계불연속거리를 결정하였다. 끝으로 불연속면의 종류, 발파공간거리 그리고 불연속면의 경사를 변화시킨 모형실험을 실시하여 파단면의 요철도를 실측하였다. 이 실측결과를 (2)식으로 계산되는 요철도의 예측치와 (3)식으로 계산되는 한계공간거리를 기준으로 대비함으로써 예측법의 타당성을 평가하였다. 실측치와 예측치를 불연속면의 종류와 경사별로 발파공간 거리를 기준으로하여 비교한 결과 overbreak + u 의 값은 예측치와 실험치가 높은 일치성을 나타내고, underbreak - u 의 값은 일치성이 다소 낮게 나타났으나 전체적으로 양호한 일치성을 나타냄으로써 파단면의 형성과 요철도의 예측법이 충분히 합리적이었음이 증명되어 불연속면을 함유하는 암반에서 Smooth Blasting 의 기구가 상당부분 밝혀졌다고 사료된다.

• Progress in Superconductivity
• /
• 제6권2호
• /
• pp.133-137
• /
• 2005

We fabricated the Au/Ni template for YBCO coated conductors and evaluated texture formation and the microstructural evolution. The cube textured Ni substrate was fabricated by rolling and recrystallization annealing, and subsequently Au layer formed on the substrate by electroless-plating method. The texture was evaluated by pole-figure with x-ray goniometer with orientation distribution function (ODF) analysis. The surface roughness and grain boundary morphology of template were characterized by atomic force microscopy (AFM) We observed that Au layer deposited epitaxially on Ni substrate and formed a strong cube texture when plating time was optimized. The full-width at half-maximum (FWHM) was $8.4^{\circ}$ for out-of-plane and $9.98^{\circ}$ for in-plane texture for plating time of 30 min. Microstructural observation showed that the Au layer was homogeneous and dense without formation of crack/microcrack. In addition, we observed that root-mean-square (RMS) and depth of grain boundary were 14.6 nm and 160 $\AA$ for the Au layer, respectively, while those were 27.0 nm and 800 $\AA$ for the Ni substrate, indicating that the electoless-plated Au layer had relatively smooth surface and effectively mollified grain groove.