• 한국표면공학회지
• /
• 제26권3호
• /
• pp.149-157
• /
• 1993

In the study of TAB(Tape Automated Bonding)technologies, Cu-Cr sputtered seed layer has been used to improve the adhesion between Polyimide and Cu film and electrical properties. But the Cu electrodeposit on Cu-Cr film had poor adhesion or powder-like form due to the surface Cr oxides on the Cu-Cr film. By means of activating the Cu-Cr film with the oxalic acid and phosphoric acid, the Cu film with the improved adhesion could be coated on the Cu-Cr sputtered film in CuSO4 solution. The etching rate was compared with increasing the Cr content of the sputtered Cu-Cr film, and anodic polarization curve in FeCl3 solution was investigated. With increasing the Cr content, the etching rate was reduced. The clean etching cross section could be obtained with increasing the concentration of FeCl3 solution. But above the 13 w/o Cr content, Cu-Cr sputtered film could not bed etched cleanly only with FeCl3 solution and additives were needed.

• 한국진공학회지
• /
• 제3권2호
• /
• pp.190-197
• /
• 1994

본 연구에서는 DC magnetron 스퍼터링법을 이용하여 고정밀, 고저항 저항체 박막으로 TaNx film을 제조하였을 때 형성될 수 있는 화합물 중 TaN0.1, TaN0.8과 TaN 박막의 Rs와 TCR특성을 평가하 고 film층의 우선방향성을 XRD를 이용하여 판명한 뒤 저항체의 Rs와 TCR에 미치는 영향을 조사하였 다. TaN0.1 박막이 35$\Omega$/$\square$의 면저항값과 안정된 TCR값을 나타내는 것을 알수 있었다. 두께50~200nm 의 TaN0.1과 Alumina 기판 사이에 정(+)의 TCR을 갖는 약 50nm의 Cr층을 증착하였을 때 Rs는 180$\Omega$/ $\square$ 과 TCR는 20ppm/$^{\circ}C$인 적층박막을 제조할 수 있었다. TaN0.1, TaN0.8 과 TaN 시편에서 화합물 형성 에 따른 Ta의 결합에너지를 ESCA를 이용하여 조사하였다. 이상의 연구결과로부터 TaN0.1 film이 TaNfilm 보다 고정밀, 고저항 박막 저항체 제조에 있어 우수한 전기저항 특성을 가지며 Cr 중간층 형성 으로 TCR이 $\pm$ppm/$^{\circ}C$정도로 안정된 고정밀 다층 저항체 박막을 형성할 수 있었다.

• 열처리공학회지
• /
• 제30권4호
• /
• pp.164-168
• /
• 2017

Intense electron beam was irradiated on the CrAlN thin films deposited in SKD61 under different incident energies and then the effect of electron beam irradiation on the enhancement of surface hardness and wear resistance was investigated. Surface hardness and wear resistance of the CrAlN films is increased proportionally with the electron beam energy. While the surface hardness of as deposited CrAlN film is Hv ($0.1g{\cdot}f$) 450, the hardness oflectron irradiated (600 eV) film is Hv ($0.1g{\cdot}f$) 2050. The width of wear track of the untreated SKD61 is $X\_{\mu}m$, while the track-width of the electron irradiated CrAlN (600 eV) film is $787{\mu}m$, respectively. From the observed results, it is supposed that the optimal electron beam irradiation can be one of the useful surface treatment technologies for the enhancement of surface hardness and wear resistance of CrAlN/SKD61, simultaneously.

• 한국재료학회지
• /
• 제14권8호
• /
• pp.558-564
• /
• 2004

In order to improve the low hardness and low wear resistance of Ti-6Al-4V alloy, plasma carburization treatment and CrN film coating were carried out. Effects of the plasma carburization and CrN coating were analyzed and compared with the non-treated alloy by mechanical and creep tests. After plasma carburization and CrN coating treatments, the carburized layer was about 150 ${\mu}m$ in depth and CrN coated layer was about 7.5 ${\mu}m$ in thickness. Hardness value of about $H_{v}$ 402 of the non-treated alloy was improved to $H_{v}$ 1600 and 1390 by plasma carburization and CrN thin film coating, respectively. Stress exponent(n) was decreased from 9.10 in CrN coating specimen to 8.95 in carburized specimen. However, the activation energy(Q) was increased from 242 to 250 kJ/mol. It can be concluded that the static creep deformation for Ti-6Al-4V alloy is controlled by the dislocation climb over the ranges of the experimental conditions.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.96-101
• /
• 2011

The thin films of TiN have been used extensively as wear-resistant materials, for instance, such as tools of high-speed cutting, metal mold forming etc. In these days, because the thin films capable of being used more severe conditions are needed, the technologies of arc ion plating are tried to improve its characteristics. The purpose of this study is to investigate the characteristics of thin films of (Ti,Cr)N compared with those of TiN. The method of arc ion plating, which is known as showing good tight-adherence and productivity, was used. After manufacturing thin films of ($Ti_{1-x}Cr_{x}$)N (x=0~1) with change of Cr in (Ti,Cr) target, atomic concentration, structure, size of crystallite, residual stress and surface roughness of thin films on substrate were investigated. As the results, it was confirmed that Cr atomic concentrations of thin films were proportionally changed with Cr atomic concentrations of target, and thin films of ($Ti_{1-x}Cr_{x}$)N (x=0~1) showed NaCl type and CrN existed as solid solution to TiN.

• 한국진공학회지
• /
• 제6권1호
• /
• pp.77-84
• /
• 1997

DC Magnetron Sputtering 방법으로 원기둥형 Alumina기판(직경 4mm, 길이 11mm) 상에 부(-)의 TCR특성의 TaN0.1(부도체)와 정(+)의 TCR특성의 Cr(금속)박막두께를 적절히 조절하므로써 초정밀 저항기를 제조하였다. 그리고 면저항(Rs)을 1k$\Omega$/수준으로 높이고 보 호막을 형성키 위하여 상부에 $Ta_2O_5$막을 입형 $Ta_2O_5/TaN_{0.1}/Cr/Al_2O_3$(substrate)의 다층 박 막저항체를 제조하였다. 적절한 조건(기판온도, $N_2$(g), Ar(g)의 유속 등)으로 상기 다층박막 내 각 막의 두께를 약10,100과 500nm두께로 증착했을 때, $Rs\approx 1k\Omega/\Box$와 $TCR\approx 20$\pm 5ppm/^{\circ}C$ 의 초정밀 저항체가 제조되었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 춘계학술발표회 논문집
• /
• pp.167-168
• /
• 2012

Films of CrN, $Cr_{40}Zr_9N$, and $Cr_{31}Zr_{16}N$ were deposited on a steel substrate by closed field unbalanced magnetron sputtering, and their oxidation behaviors at $700^{\circ}C$ and $800^{\circ}C$ for up to 60h in air were investigated. All the deposited films were composed of the CrN phase. Zirconium atoms in $Cr_{40}Zr_9N$ and $Cr_{31}Zr_{16}N$ films partially dissolved in the CrN phase. They advantageously refined the columnar structure, reduced the surface roughness, and increased the microhardness. The CrN film displayed relatively good oxidation resistance, owing to the formation of the highly protective $Cr_2O_3$ on its surface. The $Cr_{40}Zr_9N$ and $Cr_{31}Zr_{16}N$ films oxidized to $Cr_2O_3$ as the major phase and ${\alpha}-ZrO_2$ as the minor one. They oxidized primarily by the inward transport of oxygen. The addition of Zr could not increase the oxidation resistance of the CrN film, because the formed $ZrO_2$ that was intermixed in the $Cr_2O_3$-rich oxide layer was oxygen permeable, and developed the compressive stress in the oxide scale owing to the volume expansion during its formation.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.107-107
• /
• 2016

TiCrAlSiN films were developed in order to improve the high-temperature oxidation resistance, corrosion resistance, and mechanical properties of conventional TiN films that are widely used as hard films to protect and increase the lifetime and performance of cutting tools or die molds. In this study, a nano-multilayered TiAlCrSiN film was deposited by cathodic arc plasma deposition. It displayed relatively good oxidation resistance at $700-900^{\circ}C$, owing to the formation protective oxides of $Al_2O_3$, $Cr_2O_3$, and $SiO_2$, and semiprotective $TiO_2$. At $1000^{\circ}C$, the increased temperature led to the formation of the imperfect oxide scale that consisted primarily of the outer ($TiO_2$,$Al_2O_3$)-mixed scale and inner ($TiO_2$, $Al_2O_3$, $Cr_2O_3$)-mixed scale.

• 한국표면공학회지
• /
• 제38권4호
• /
• pp.137-143
• /
• 2005

CrSiN coatings of stepwise changing Si concentration were deposited on stainless steel by closed field unbalanced magnetron sputtering (CFUBM) system. Microstructure of the films due to the Si concentration is measured by XRD. The corrosion behavior of CrSiN coatings in deaerated $3.5\%$ NaCl solution was investigated by potentiodynamic test, electrochemical impedance spectroscopy (EIS) and surface analyses. The microstructure of CrSiN film depends on the Si concentration. When Si/(Cr+si) was under $11.7\%$, preferred orientation is defined at CrN(220), CrN(311) and $Cr_2N(111).$ The results of potentiodynamic polarization tests showed that the corrosion current density and porosity decreased with increasing Si/(Cr+si) ratio. EIS measurements showed that the corrosion resistance of Si-bearing CrN was improved by phase transformation of the film, which leads to increase of pore resistance and charge transfer resistance. At the Si(Cr+si) ratio of 20, the Si-bearing CrN possesses the best corrosion resistance due to the highest pore resistance and charge transfer resistance.

• 전기화학회지
• /
• 제3권4호
• /
• pp.211-218
• /
• 2000

마멸전극기법과 교류 임피던스법으로 스테인리스강의 합금원소, Cr, Mo, N가 합금의 재부동태 특성에 미치는 영향을 조사하였다. Fe-Cr, Fe-Cr-Mo, 304, 304LN, 316, 316LN등의 스테인리스강을 시편으로 사용하였으며 각 합금의 부동태 피막의 전기화학적 특성은 in-situ시험 기법인 d.c와 a.c전기화학적 기법을 각각 이용하였다 스테인리스강이 국부부식에 대하여 강한 저항성을 가지려면 부식 환경에서도 치밀한 부동태 피막을 유지해야 하고 피막의 파괴가 발생하더라도 재부동태 속도가 빨라야 하기 때문에 합금원소가 시간에 따른 재부동태 전류밀도와 재부동태 속도에 미치는 영향을 마멸 전극 시험법과 교류 임피던스 시험법으로 알아보았다. 부동태 피막의 안정성, 재부동태 속도 그리고 합금원소 사이의 관계를 규명하기 위하여 실험결과를 분석하였다.