• 공업화학
• /
• 제35권2호
• /
• pp.96-99
• /
• 2024

구리 마이크로입자의 표면을 나노섬유형태의 포름산구리로 합성하고 포름산과 혼합하여 구리판을 접합할 수 있는 소결 페이스트를 합성하였다. 평균 10 ㎛의 구리 마이크로입자는 400 ℃ 이상에서 표면이 산화구리 나노섬유로 합성되고 포름산과 혼합하여 표면이 포름산화된 구리 마이크로입자가 합성된다. 포름산구리는 구리 벌크입자나 나노입자의 녹는점에 비해 낮은 온도인 210 ℃에서 구리로 분해되어 저온 소결로 구리판의 접합이 가능하다. 표면을 나노섬유 형태로 제어하여 표면적을 높여 포름산구리로의 반응속도, 응집에 필요한 접촉면적, 포름산구리의 분해속도 등이 증가하여 짧은 시간에 소결할 수 있도록 하였다.

• Bulletin of the Korean Chemical Society
• /
• 제35권1호
• /
• pp.147-150
• /
• 2014

Copper ink has been prepared by mixing copper(II) formate and 2-ethyl-1-hexylammonium bicarbonate (EHABC) to overcome some weak points such as aggregation and degradation of copper nano-type ink. Ink was coated on glass substrate and calcined at $110^{\circ}C$ to $150^{\circ}C$ to generate electrically conductive copper film under two different atmospheres such as nitrogen gas and gaseous mixture of formic acid and methanol. The lowest resistivity of $1.88{\mu}{\Omega}{\cdot}cm$ of copper film was obtained at $150^{\circ}C$ in gaseous formic acid condition. The long-term resistivity shows to increase from $1.88{\mu}{\Omega}{\cdot}cm$ to $2.61{\mu}{\Omega}{\cdot}cm$ after one month.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1444-1446
• /
• 1998

Direct writing of copper lines has been achieved by pyrolytic decomposition of copper formate films using a focused argon ion laser beam($\lambda$ =514.5nm) on a glass. The thickness and linewidth of the deposited copper films were considered as a function of laser power and scan speed. As the result from AES, there are no other elements except for copper after decomposition in the atmospheric ambient.

• 한국응용과학기술학회지
• /
• 제19권4호
• /
• pp.251-257
• /
• 2002

Liquid-phase methanol synthesis via methyl formate using coal-derived syngas was carried out in a bench-scale(diameter 173 mm and dispersion height 1200 mm) slurry bubble column reactor(SBCR) Under the condition of $180^{\circ}$. 61 atm, 30 L/min, $H_{2}$/CO=2 and a slurry mixture of 2 kg of copper chromite and 0.5 kg of $KOCH_{3}$ suspended in 14 L of methanol, the per pass conversions of syngas is 6 %, maximum concentration of methyl formate 3.088 mol% and maximum synthesis, rate of methanol 0.8 gmole/kg ${\cdot}$ hr. It is a significant evidence that copper chromite powder as heterogeneous catalyst didn't active for the hydrogenolysis of methyl formate to methanol, resulting copper chromite powder was not efficiently suspended in a slurry mixture. To enhance the hydrogenolysis of methyl formate in liquid-phase methanol synthesis process, the designed SBCR have need to use the higher specific gravity solvent and/or decrease the catalyst particle size.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.663-666
• /
• 2000

Laser direct writing of micro-patterned copper lines has been achieved by pyrolytic decomposition of copper formate films (Cu(HCOO)$_2$$.$4H$_2$O), as a precursor, using a focused Ar$\^$+/ laser beam ($\lambda$= 514 nm) on PCB boards and glass substrates. The linewidth and thickness of the lines were investigated as a function of laser power and scan speed. The profiles of the lines were measured by scanning electron microscope (SEM), surface profiler (${\alpha}$-step) and atomic force microscopy (AFM). The electrical resistivities of the patterned lines were also investigated as a function of laser parameter using probe station and semiconductor analyzer. we compared resistivities of the patterned lines with that of the Cu bulk, respectively.

• 한국환경과학회지
• /
• 제17권9호
• /
• pp.981-992
• /
• 2008

This study examined how to produce new methods of copper (II) sulfate crystallization by using a small-scale chemistry tool such as small-scale reaction surface and petri dish. The making of copper(II) sulfate is included in the 5th grade elementary science textbooks. Various copper(II) compounds were reacted with a 2 M sulfuric acid solution. The result of this study is as follows: Seven small amounts of copper(II) compounds were reacted with a few drops of 2 M sulfuric acid solution at room temperature to make a copper(II) sulfate crystal of triclinic shape. Using the petri dish method, a copper(II) sulfate crystal could be identified within one hour of reacting copper(II) hydroxide, copper(II) carbonate, copper(II) nitrate, copper(II) perchlorate, cupric(II) formate from a few drops of 2 M sulfuric acid solution at room temperature. When using the lap top method for copper(II) perchlorate, cupric formate, a proper crystal could be identified within one hour as well. SSC methods were used for the first time to make a copper sulfate crystal via chemical reaction. We can make a copper(II) sulfate crystal using a simple method which is easier, safer and saves time in class. And since a small quantity of chemicals are being used in SSC chemical methods, waste is greatly reduced. This lessens the amount of environmental problems caused by the experiment. This can be helpful in preserving nature. In addition the cost of chemical and laboratory equipment is greatly reduced because it uses material that we find in our daily lives. There will be continued study of small-scale methods such as improvement of new programs, study and training of teachers, and securing SSC tools. I would like to suggest such as SSC methods are applicable in elementary School Science. I would like it to become a wide spread program.

• 한국기계가공학회지
• /
• 제15권6호
• /
• pp.89-94
• /
• 2016

Consumer orientation requires that companies understand consumer needs and produce products that meet their expectations. This study proposes a new additive method that creates a polymer/metal bonding layer and thus can lighten the weight of helmets to develop a consumer-oriented 3D printing helmet. The composite solution is experimentally prepared with copper formate and a photopolymer resin. Stereolithography apparatus and photothermal reactions are introduced to fabricate an adhesive hybrid layer of copper metal and polymer. A UV pulse laser with a 355 nm wavelength was installed to simplify this process. Resistance, adhesion, and accuracy were investigated to evaluate the properties of the layer produced.

• 공업화학
• /
• 제7권6호
• /
• pp.1053-1060
• /
• 1996

Sodium amide에 의한 methyl propyl ketone과 ethyl formate의 반응으로 킬레이트 추출제의 하나인 $\beta$-ketohexanal(이하 KHA)를 합성하고, KHA-클로로포름에 의한 구리의 추출평형 실험을 통하여 추출특성을 고찰하였다. 흡광도를 측정하여 추출제 KHA의 상간 분배계수와 해리상수, KHA와 구리간 킬레이트의 안정도 상수와 분배계수 및 총괄 추출 평형상수등을 구하고, 추출기구를 구명하였다 합성한 추출제에 의한 구리의 추출율은 pH 5 이상에서 거의 100%이었고, Cu-Zn-Cd 혼합 금속으로부터 구리의 선택적 추출이 가능하였다. KHA-클로로포름에 의한 구리의 추출 화학종은 $CuR_2$였으며 추출 평형 식은 $Cu^{2+}+2{\overline{HR}}{\rightarrow}{\overline{CuR{_2}}}+2H^+$로 표시되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.889-891
• /
• 1998

Copper films have been deposited on glass substrate via a thermal decomposition of copper(II) formate using a focused $Ar^+$ laser emitting at 514 nm. The growth kinetics of these Cu films was investigated as a function of laser power and scan speed which varied in the range of 70-150 mW and 0.1-20 mm/s, respectively. The resistivity of the copper films was a factor of about 20 higher than· that of bulk value, but the resistivity decreased due to changes in morphology and porosity of the deposit after annealing at $300^{\circ}C$, 5 min. and was about $10{\mu}{\Omega}cm$.

• 한국전기전자재료학회논문지
• /
• 제13권11호
• /
• pp.969-975
• /
• 2000

Laser direct writing of micro-patterned copper lines has been achieved by pyrolytic decomposition of copper formate films (Cu(HCOO)$_2$.4$H_2O$), as a metallo-organic precursor, using a focused CW Ar$^{+}$ laser beam (λ=514nm) on PCB boards and glass substrates. The linewidth and thickness of the lines wee investigated as a functin of laser power and scan speed. The profiles of the lines were measured by scanning electron microscope (SEM), surface profiler ($\alpha$-step) and atomic force measured by scanning electron microscope (SEM), surface profiler ($\alpha$-step) and atomic force microscopy (AFM). The electrical resistivities of the patterned lines were also investigated as a function of laser parameters using probe station and semiconductor analyzer. We compared resistivities of the patterned copper lines with these of the Cu bulk. Resistivities decreased due to changes in morphology and porosity of the deposit, which were about 3.8 $\mu$$\Omega$cm and 12$\mu$$\Omega$cm on PCB and glass substrates after annealing at 30$0^{\circ}C$ for 5 minutes.s.