• Journal of Sensor Science and Technology
• /
• v.10 no.1
• /
• pp.1-8
• /
• 2001

Conventional microgyroscopes of vibrating type require resonant frequency tuning of the driving and sensing modes to achieve high sensitivity. These tuning conditions depend on each fabricated microgyroscopes, even though the microgyroscopes are identically designed. A new micromachined resonator, which is applicable to microgyroscopes with self-toning characteristics, is presented. Since the laterally driven two degrees of freedom (2DOF) resonator was designed as a symmetric structure with identical stiffness in two orthogonal axes, the resonator is applicable to vibrating microgyroscopes, which do not need mode tuning. A dynamic model of the resonator was derived considering gyroscopic application. The dynamic model was evaluated by experimental comparison with fabricated resonators. The microgyroscopes were fabricated using a simple 2-mask-process of a single polysilicon layer deposited on an insulator layer. The feasibility of the resonator as a vibrating microgyroscopes with self-tuning capability is discussed. The fabricated resonators of a particular design have process-induced non-uniformities that cause different resonant frequencies. For several resonators, the standard deviations of the driving and sensing frequencies were as high as 1232Hz and 1214Hz, whereas the experimental average detuning frequency was 91.75Hz. The minimum detuned frequency was 68Hz with $0.034mVsec/^{\circ}$ sensitivity. The sensitivity of the microgyroscopes was low due to process-induced non-uniformity; the angular rate bandwidth, however, was wide. This resonator could be successfully applicable to a vibrating microgyroscopes with high sensitivity, if improvements in uniformity of the fabrication process are achieved. Further developments in improved integrated circuits are expected to lower the noise level even more.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.15 no.1
• /
• pp.1-10
• /
• 2003

In this paper, the laboratory test results with middle-sired ,soil box test in modeling the in-situ installing of horizontal drains are discussed the estimation of the optimum negative pressure. The test was carried out in the different vacuum pressure conditions together with the measurement for the settlement and volume change of drained water by the installed drains during the consolidation process. After the test, the water content was measured to both directions of lateral distance from the drain and depth of the soil, to find out the distribution of ground improvement and strength enhancement. From the analysis on the distribution of water content, the gradual application of vacuum pressure to higher level by pre-determined stages starting from low vacuum pressure is found to be effective and desirable. In the comparison of the degrees of consolidation with elapsed time, the calculated value by the prediction method based on the Barren's conventional theory showed a good agreement with the measured value. With this, It is positively considered that the applicability of the prediction method based on Barren's theory to the practical design of horizontal drains can be justified such as in the calculation of drain spacing and consolidation period.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2004.04a
• /
• pp.12-27
• /
• 2004

Thanks to spectacular advances in the techniques for identifying proteins separated by two-dimensional electrophoresis and in methods for large-scale analysis of proteome variations, proteomics is becoming an essential methodology in various fields of plant sciences. Plant proteomics would be most useful when combined with other functional genomics tools and approaches. A combination of microarray and proteomics analysis will indicate whether gene regulation is controlled at the level of transcription or translation and protein accumulation. In this review, we described the catalogues of the rice proteome which were constructed in our program, and functional characterization of some of these proteins was discussed. Mass-spectrometry is a most prevalent technique to identify rapidly a large of proteins in proteome analysis. However, the conventional Western blotting/sequencing technique us still used in many laboratories. As a first step to efficiently construct protein data-file in proteome analysis of major cereals, we have analyzed the N-terminal sequences of 100 rice embryo proteins and 70 wheat spike proteins separated by two-dimensional electrophoresis. Edman degradation revealed the N-terminal peptide sequences of only 31 rice proteins and 47 wheat proteins, suggesting that the rest of separated protein spots are N-terminally blocked. To efficiently determine the internal sequence of blocked proteins, we have developed a modified Cleveland peptide mapping method. Using this above method, the internal sequences of all blocked rice proteins (i. e., 69 proteins) were determined. Among these 100 rice proteins, thirty were proteins for which homologous sequence in the rice genome database could be identified. However, the rest of the proteins lacked homologous proteins. This appears to be consistent with the fact that about 30% of total rice cDNA have been deposited in the database. Also, the major proteins involved in the growth and development of rice can be identified using the proteome approach. Some of these proteins, including a calcium-binding protein that fumed out to be calreticulin, gibberellin-binding protein, which is ribulose-1,5-bisphosphate carboxylase/oxygenase activate in rice, and leginsulin-binding protein in soybean have functions in the signal transduction pathway. Proteomics is well suited not only to determine interaction between pairs of proteins, but also to identify multisubunit complexes. Currently, a protein-protein interaction database for plant proteins (http://genome .c .kanazawa-u.ac.jp/Y2H)could be a very useful tool for the plant research community. Recently, we are separated proteins from grain filling and seed maturation in rice to perform ESI-Q-TOF/MS and MALDI-TOF/MS. This experiment shows a possibility to easily and rapidly identify a number of 2-DE separated proteins of rice by ESI-Q-TOF/MS and MALDI-TOF/MS. Therefore, the Information thus obtained from the plant proteome would be helpful in predicting the function of the unknown proteins and would be useful in the plant molecular breeding. Also, information from our study could provide a venue to plant breeder and molecular biologist to design their research strategies precisely.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.49 no.2
• /
• pp.105-109
• /
• 2004

Field studies were conducted in the southeastern Korea ($36^{\circ}$N) on a commerce silt loam soil at paddy field. Seed were manually planted on 16 July 2003. Plants were planted with plant densities of 70${\times}$10 cm (row width x plant spacing), 50 x 10 cm, and 30 ${\times}$10 cm. Two seedlings per hill were taken prior to V3 stage. Fertilizer was applied prior to plant at a rate of 30-30-34 kg (N-$\textrm{P}_2\textrm{O}_5$-$\textrm{K}_2\textrm{O}$) per ha. Experimental design was a randomized complete block in a split plot arrangement with three replications. Yield from different planting densities responded similarly in three soybean cultivars and increased when planting density increased. Somyeongkong showed the highest increasing rate of yield about 26% by 338 g $\textrm{m}^{-2}$ at 30 x l0 cm compared to yield of conventional planting density (70 x 10 cm). Also, the planting density significantly affected pod and seed number and seed weight, but not seed per pod. The tallest plant appeared at 30${\times}$10 cm. The change of leaf area according to days after emergence showed differently in soybean cultivars. The highest and lowest total dry matter production per square meter appeared at 30 x 10 cm and at 70 x 10 cm, respectively. Crop growth rate (CGR) showed greater at R3∼R4 stages compared with V7∼R2 or R2∼R3 growth stages and showed the greatest at 30 x 10 cm in three soybean cultivars. As late planted soybean, there was a significant relation between seed yield and CGR, and leaf area index (LAI) according to planting densities at before and after the flowering stage. Relationship between seed yield and CGR in three planting densities showed a highly significant positive relation ($\textrm{R}^2$=0.757) at R3 to R4 stages, and significant relations ($\textrm{R}^2$=0.505, 0.617) at V7 to R2 and V2 to V3. Also, there was a highly significant positive difference between seed yield and LAI during R3 to R4 and R2 to R3 stages.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.3_4
• /
• pp.407-417
• /
• 2003

The purpose of this study is to develop designs and patterns of a functional brassiere. For this purpose, women who have protruding and drooping breasts with 75B for their brassiere size were sampled. The fitting test for the fitness and function of test brassiere and control brassiere were carried out twice and compared the results from the both in terms of front, rear and side looks. The results of this study can be summarized as follows; 1. The results from measuring the level of sag and spread, and volume and protrusion of breasts shows that there are some distinctive differences in the measurements before and after wearing the test brassiere and the test brassiere is proved to be very effective in correcting breasts' shapes. 2. Front look: Since the two front cutting lines of the test brassiere served to have the curved main part pressing against the breasts, it could support breasts to more than satisfactory level. In addition, upperline panel and side panels of the test brassiere were found to have the upperline of the upper cup pressed against the breasts and at the same time it pressed and gathered the flab around upper part of the breasts and armpits that helped to rearrange the shape of the breasts. It is also proved that the two-pieced test brassier was found to be more functional in supporting the lower cup of the breasts. 3. Rear look: The test brassier was made up of two wide U-shaped wings with 2.5cm tape on its lower sides. Each wing has 4 lines and 3 hems (5.5cm). For this reason, the test brassiere was tighter and better fitted on its back. 4. Side look and entire look: The wings of the test brassiere might look wider than that of the control brassier which has conventional straight-shaped wings, but it was analyzed that the test brassiere held the upper and lower sides of the wings more effectively to be more pressed against the breast. Therefore, the test brassiere scored higher in terms of adjusting to body movements, while the control brassiere looked better in overall terms. 5. The functional brassier fur protruding and drooping breasts developed from the experiments of this study is a full side stretch brassiere which covers the entire breasts satisfactorily. The pattern drafting methods are suggested in to .

• The Journal of the Korea Contents Association
• /
• v.13 no.9
• /
• pp.504-514
• /
• 2013

Purpose: This study was to identify the educational effects of self directed learning applying basic nursing practice contents of e-learning on nursing students' knowledge, self-confidence, and learning satisfaction. Method: This study applied a quasi-experimental pre-test and post-test control group design with 63 freshman nursing students (31 experimental group, 32 control group) of G. university in Incheon, Korea as subjects. The e-learning content was about the application of topical medications, central line care, and blood transfusion. All were available at the web site in school. Self-directed e-learning was more than 120 min.(3 times a week, 2 weeks)during Sep-Nov in 2011. In both groups, there were no significant difference in general characteristics, self-directed learning readiness, knowledge, and self-confidence for the pre-homogeneity. Results: The experimental group showed a higher level of improvement in knowledge and learning satisfaction but not significantly. However, the self-confidence was significantly improved in the experimental group. Conclusion: When self-directed learning using e-learning contents added to the conventional practical class, it may be beneficial for the nursing students to learn skills effectively.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.3
• /
• pp.193-202
• /
• 2009

This study was conducted to identify the magnitude of first flush in small city urban area and to provide the basic information on the criteria of stormwater runoff management. Monitoring site was surrounded by residential area in Gumi city near to national industrial complex and the monitoring period was three months. Total watershed area was 24.9 ha, where 80% of the area is impervious (asphalt of pavement type). Periodic monitoring of conventional water quality parameters were conducted with six times of rainfall period. Event mean and site mean concentrations for all the parameters were calculated based on the analytical results. Particle size distribution was 9.82 ${\mu}m$ for $D_{0.1}$, 38.99 ${\mu}m$ for $D_{0.5}$ and 159.61 ${\mu}m$ for $D_{0.9}$ respectively. First flush phenomenon was detected highly in particulate solids than dissolved ones. The first flush criteria results by mass first flush contained between 44.4% to 58.5% pollutant mass during the first 30% of runoff volume. Mass first flush ratio and particle size distribution obtained in this study are expected to provide the basic information for the design and operation of non-point source treatment facility.

• Journal of Broadcast Engineering
• /
• v.10 no.3
• /
• pp.270-285
• /
• 2005

A joint design scheme is proposed to optimize the up/down scaler and the motion vector estimation module in the transcoder system. The proposed scheme first optimizes the resolution scaler for a fixed motion vector, and then a new motion vector is estimated for the fixed scaler. These two steps are iteratively repeated until they reach a local optimum solution. In the optimization of the scaler, we derive an adaptive version of a cubic convolution interpolator to enlarge or reduce digital images by arbitrary scaling factors. The adaptation is performed at each macroblock of an image. In order to estimate the optimal motion vector, a temporary motion vector is composed from the given motion vectors. Then the motion vector is refined over a narrow search range. It is well-known that this refinement scheme provides the comparable performance compared to the full search method. Simulation results show that a jointly optimized system based on the proposed algorithms outperforms the conventional systems. We can also see that the algorithms exhibit significant improvement in the minimization of information loss compared with other techniques.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.1
• /
• pp.48-57
• /
• 2020

MCU used in applications such as wireless chargers and USB type-C require MTP memory with a small cell size and a small additional process mask. Conventional double poly EEPROM cells are small in size, but additional processing masks of about 3 to 5 sheets are required, and FN tunneling type single poly EEPROM cells have a large cell size. In this paper, a 110nm MTP cell using a vertical PIP capacitor is proposed. The erase operation of the proposed MTP cell uses FN tunneling between FG and EG, and the program operation uses CHEI injection method, which reduces the MTP cell size to 1.09㎛2 by sharing the PW of the MTP cell array. Meanwhile, MTP memory IP required for applications such as USB type-C needs to operate over a wide voltage range of 2.5V to 5.5V. However, the pumping current of the VPP charge pump is the lowest when the VCC voltage is the minimum 2.5V, while the ripple voltage is large when the VCC voltage is 5.5V. Therefore, in this paper, the VPP ripple voltage is reduced to within 0.19V through SPICE simulation because the pumping current is suppressed to 474.6㎂ even when VCC is increased by controlling the number of charge pumps turned on by using the VCC detector circuit.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.1
• /
• pp.64-71
• /
• 2020

eFuse OTP memory IP is required to trim the analog circuit of the gate driving chip of the power semiconductor device. Conventional NMOS diode-type eFuse OTP memory cells have a small cell size, but require one more deep N-well (DNW) mask. In this paper, we propose a small PMOS-diode type eFuse OTP memory cell without the need for additional processing in the CMOS process. The proposed PMOS-diode type eFuse OTP memory cell is composed of a PMOS transistor formed in the N-WELL and an eFuse link, which is a memory element and uses a pn junction diode parasitic in the PMOS transistor. A core driving circuit for driving the array of PMOS diode-type eFuse memory cells is proposed, and the SPICE simulation results show that the proposed core circuit can be used to sense post-program resistance of 61㏀. The layout sizes of PMOS-diode type eFuse OTP memory cell and 512b eFuse OTP memory IP designed using 0.13㎛ BCD process are 3.475㎛ × 4.21㎛ (= 14.62975㎛2) and 119.315㎛ × 341.95㎛ (= 0.0408mm2), respectively. After testing at the wafer level, it was confirmed that it was normally programmed.