• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.49 no.2
• /
• pp.68-73
• /
• 2000

This paper addresses the analysis and design of fuzzy control systems for a class of complex nonlinear systems. Firstly, the nonlinear system is represented by Takagi-Sugeno(TS) fuzzy model and the global controller is constructed by compensating each linear model in the rule of TS fuzzy model. The design of conventional TS fuzzy-model-based controller is composed of two processes. One is to determine the static state feedback gain of each local model and the other is to validate the stability of the designed fuzzy controller. In this paper, we propose an alternative methods for the design of TS fuzzy-model-based controller. The design scheme is based on the extension of conventional optimal control theory to the design of TS fuzzy-model-based controller. By using the proposed method, the design and stability analysis of the TS fuzzy model-based controller is reduced to the problem of finding the solution of a set of algebraic Riccati equations. And we use the recently developed interior point method to find the solution of AREs, where AREs are recast as the LMI formulation. A numerical simulation example is given to show the effectiveness and feasibiltiy of the proposed fuzzy controller design method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.12
• /
• pp.1061-1068
• /
• 2013

In this paper, we propose a $M{\times}M$ beam-space multiple input multiple output (BS-MIMO) system using electronically steerable parasitic array radiator (ESPAR) antenna. Conventional MIMO method required multiple RF chains because it map the transmission signals onto multiple antennas. So, conventional MIMO system has high cost for design and high energy consumption at RF circuit. Also, It is difficult to use MIMO system in battery based mobile terminals with limited physical area. In order to solve these problems, BS-MIMO technique which map the data signal onto bases in beam space domain was proposed using ESPAR antenna with single RF chain. This paper, we design and analyze the performance of extended $M{\times}M$ BS-MIMO technique. Simulation results show that the proposed BS-MIMO system has similar BER performance compare to conventional MIMO scheme. Therefore, BS-MIMO system with single RF chain will has a low RF power consumption and low cost for RF hardware design as compared with conventional MIMO technique with multiple RF chains.

• Journal of Korea Society of Industrial Information Systems
• /
• v.22 no.1
• /
• pp.53-59
• /
• 2017

This Paper Proposes a New High-speed Design Methodology for Delay Insensitive Asynchronous Circuits Combining with a Pseudo-NMOS Structure used for High Performance in Synchronous Circuits. Null Convention Logic(NCL) of Conventional Delay-Insensitive Asynchronous Design Methodologies has many Advantages of High Reliability, Low Power Consumption, and Easy Design Reuses not Dependant on Semiconductor Technology. However. the Conventional NCL Gates has a Complicated Stack Structure, so it Suffers from Increased Circuit Delay. Therefore, a New NCL Gates and its Pipeline Structure for High Performance, and the Proposed Methodology has been Designed and Evaluated by a $4{\times}4$ Multiplier Designed using SK-Hynix 0.18 um CMOS Technology. The Experimental Results are Compared with a Conventional NCL in Terms of Power and Delay and shows that the Propagation Delay of the Proposed Multiplier is Reduced by 85% Compared with the Conventional NCL Multiplier.

• The Journal of Advanced Prosthodontics
• /
• v.13 no.3
• /
• pp.144-151
• /
• 2021

PURPOSE. The purpose of this in vitro study was to investigate the wear resistance and surface roughness of three interim resin materials, which were subjected to chewing simulation. MATERIALS AND METHODS. Three interim resin materials were evaluated: (1) three-dimensional (3D) printed (digital light processing type), (2) computer-aided design and computer-aided manufacturing (CAD/CAM) milled, and (3) conventional polymethyl methacrylate interim resin materials. A total of 48 substrate specimens were prepared. The specimens were divided into two subgroups and subjected to 30,000 or 60,000 cycles of chewing simulation (n = 8). The wear volume loss and surface roughness of the materials were compared. Statistical analysis was performed using one-way analysis of variance and Tukey's post-hoc test (α=.05). RESULTS. The mean ± standard deviation values of wear volume loss (in mm³) against the metal abrader after 60,000 cycles were 0.10 ± 0.01 for the 3D printed resin, 0.21 ± 0.02 for the milled resin, and 0.44 ± 0.01 for the conventional resin. Statistically significant differences among volume losses were found in the order of 3D printed, milled, and conventional interim materials (P<.001). After 60,000 cycles of simulated chewing, the mean surface roughness (Ra; ㎛) values for 3D printed, milled, and conventional materials were 0.59 ± 0.06, 1.27 ± 0.49, and 1.64 ± 0.44, respectively. A significant difference was found in the Ra value between 3D printed and conventional materials (P=.01). CONCLUSION. The interim restorative materials for additive and subtractive manufacturing digital technologies exhibited less wear volume loss than the conventional interim resin. The 3D printed interim restorative material showed a smoother surface than the conventional interim material after simulated chewing.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.3
• /
• pp.55-60
• /
• 2008

Until a recent date, the surface finish generated in turning by the conventional cutting tool is directly related to the feed rate and the size of the tool nose radius. With this tool a large feed rate will give poorer surface finish and a large nose radius will generate a better surface finish. Recently a new concept in the tool design is introduced to achieve a better surface finish at a higher feed rate. This is the wiper tool, which has the portion of nose with infinite radius. This can remove the ridges left when the conventional tool is used. In this study two series of cutting tests with the wiper tool and the conventional tool are carried out under the various cutting conditions of cutting depth, feed rate and cutting speed. The effects of the wiper design and the cutting conditions on the surface roughness resulted are carefully examined and compared.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.627-630
• /
• 2004

The PID type controller has been widely used in industrial application due to its simply control structure, ease of design, and inexpensive cost. However, control performance of the PID type controller suffers greatly from high uncertainty and nonlinearity of the system, large disturbances and so on. This paper presents a hybrid fuzzy logic proportional plus conventional integral derivative controller (fuzzy P+ID). In comparison with a conventional PID controller, only one additional parameter has to be adjusted to tune the fuzzy P+ID controller. In this case, the stability of a system remains unchanged after the PID controller is replaced by the fuzzy P+ID controller without modifying the original controller parameters. Finally, the proposed hybrid fuzzy P+ID controller is applied to BLDC motor drive. Simulation results demonstrated that the control performance of the proposed controller is better than that of the conventional controller.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.7
• /
• pp.75-81
• /
• 1993

In this paper, New type of Static Edge Triggered D Flip-Flop Circuits which are effective for the sequencial selecting and addressing of Matrix type Electrodes being applied to Flat Display Devices is proposed by the Design Technique using the Transmission Characteristics of Feedback Transistors and Charge Back Up Function. These Circuits composed of 2-4 less transistors in number than Conventional Static D Flip Flop's have some advantages that the Maximum Transition Time of Clock Signals allowed is increased by 100-450 times more than that of the Conventional circuit at 100KHz Clock Frequence and Circuit Safety is much increased by making the wider ranges, 1-4V, of Clock Levelas a Non-operating periods than 3-3.2V ranges in case of the Conventional Circuit at 10MHz clock frequence. By these advantages, These circuits can be very effectively used in case that clock signal has long transition time, especially on the low frequency operation.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.2
• /
• pp.72-79
• /
• 2000

A new optimal tool design model which can be minimized the resultant cutting forces under the constrains of variables was developed. The resultant cutting forces are used as the objective function and tool angles are used as the variables. Cutting experiments of tool wear and chip length using the new and conventional tools wee carried out. Tool life of optimized cutter are more increased than those of conventional cutter by 2.29 times and 2.52 times at light and at heavy cutting conditions respectively. Chip length of optimized cutter are more increased than those of conventional cutter It is considered that the decrease of the resultant cutting forces is the cause that an effective rake and shear angles by the shape of optimal cutter.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.11
• /
• pp.53-62
• /
• 1997

In this study, a controller design method is proposed for controlling the discrete-time chaotic systems efficiently. The proposed control method is based on Generalized Predictive Control and uses NARMAX models as controlled models. In order to evaluate the performance of the proposed method, a proposed controller is applied to discrete-time chaotic systems, and then the control performance and initial sensitivity of the proposed controller are compared with those of the conventional model-based controler through computer simulations. Through simulations results, it is shown that the control performance of the proposed controller is superior to that of the conventional model-based controller and shown that the peorposed controller is less sensitive to initial values of discrete-time chaotic systems in comparison with the conventional model-based controller.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.2
• /
• pp.63-66
• /
• 2017

This research was about shielded trench gate power MOSFET for low voltage and high speed. We used T-CAD tool and carried out process and device simulation for exracting design and process parameters. The exracted parameters was used to design shieled and conventional trench gate power MOSFET. And The electrical characteristics of shieled and conventional trench gate power MOSFET were compared and analyzed for their power device applications. As a result of analyzing electrical characteristics, the recorded breakdown voltages of both devices were around 120 V. The electric distributions of shielded and conventional trench gate power MOSFET was different. But due to the low voltage level, the breakdown voltage was almost same. And the other hand, the threshold voltage characteristics of shielded trench gate power MOSFET was superior to convention trench gate power MOSFET. In terms of on resistance characteristics, we obtained optimal oxied thickness of $3{\mu}m$.