• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2064-2069
• /
• 2008

The Resonance Control Cooling System (RCCS) prototype installed in KAERI site has been designed to control the resonant frequency of the normal conducting drift tube linac (DTL) for the Proton Engineering Frontier Project (PEFP). The RCCS water pumping skid is composed of two channels as a by-passing the cooling water and a plate heat exchanger. The required temperature can be achieved by mixing both channels in order to control its the resonant frequency at 350 MHz. The temperature controlled water pumping skid operates in combination with the Low Level Radio Frequency (LLRF) system. We have discussed the design, modeling with each components, control scheme, fabrication and test results of the water pumping skid for resonant frequency control of the DTL cavity. In conclusion, the fabricated RCCS prototype through the optimization of modeling has corresponded with the design requirement and concept.

• ETRI Journal
• /
• 제33권6호
• /
• pp.897-903
• /
• 2011

A hybrid ${\Delta}{\Sigma}$ modulator for audio applications is presented in this paper. The pulse generator for digital-to-analog converter alleviates the requirement of the external clock jitter and calibrates the coefficient variation due to a process shift and temperature changes. The input resistor network in the first integrator offers a gain control function in a dB-linear fashion. Also, careful chopper stabilization implementation using return-to-zero scheme in the first continuous-time integrator minimizes both the influence of flicker noise and inflow noise due to chopping. The chip is implemented in a 0.13 ${\mu}m$ CMOS technology (I/O devices) and occupies an active area of 0.37 $mm^2$. The ${\Delta}{\Sigma}$ modulator achieves a dynamic range (A-weighted) of 97.8 dB and a peak signal-to-noise-plus-distortion ratio of 90.0 dB over an audio bandwidth of 20 kHz with a 4.4 mW power consumption from 3.3 V. Also, the gain of the modulator is controlled from -9.5 dB to 8.5 dB, and the performance of the modulator is maintained up to 5 nsRMS external clock jitter.

• 대한지역사회영양학회지
• /
• 제5권2호
• /
• pp.333-342
• /
• 2000

The purpose of this study was to evaluate microbiological quality for each stage of the kimbap manufacturing process in summer and winter. Under the various controlled conditions through the simulation, the time-temperature data were collected and the microbiological quality(including total plate count, coliforms, and fecal coliform count) were evaluated. To determine the expected shelf life of Kimbap, a microbiolgical analysis according to the length of the storage time was performed. The microbiological analysis on both sanitary and unsanitary utensils was compared. The microbiological quality of the raw materials of Kimbap in summer was not at an acceptable level, but that of the heat-treated raw materials of Kimbap met the requirement according to the standards set by the Natick Research Center. The number of the microorganisms of the unsanitary utensils and the Kimbap made from unsanitary utensils was more than the acceptable criteria. Sanitary management is necessary to prohibit cross-contamination and to manufacture Kimbap safely. Results from storage times and storage temperature conditions(chilled and room-temperature storage) showed that the expected shelf-life of the Kimbap with the room-temperature storage was as less than 3 hours in summer, while it was as 7-10 hours in winter.

• Journal of Biosystems Engineering
• /
• 제25권4호
• /
• pp.257-264
• /
• 2000

A tractor attached TMR(model 430) mixer has been developed in a previous study. However, the mixer was found to be improved through field applications in its capacity, manufacturing cost, ergonomic design and power-train requirement. The TMR mixer was modified into a model TMR500, approved by Institute of Agricultural Mechanization, as follows : 1. Roughage cutting system was seperated from the mixer, resulting in the 33% reduction of manufacturing cost. 2. Enlarged hopper capacity enabled to feed 60 heads at a batch. 3. Hydraulically controlled gate system saved ergonomic man power. 4. Power transmission system was changed from a chain-sprocket system(27:1) to the gear-train reduction system(38.6:1) to satisfy the recommended use of 540rpm PTO input.

• 한국정밀공학회지
• /
• 제13권5호
• /
• pp.67-73
• /
• 1996

The necessity for more accurate automatic flatness control(AFC) system has increased of customers' requirement for cold rolled steel sheet. Therefore, many cold rolling mills replaced its AFC system with a measuring roll of the contact type form the non-contact type. In this paper. The performance of AFC system of contact type has been investigated under industrial conditions. It has two kinds of actuator: roll bender, spot cooling system. The test results are as follows: The more strip thickness is thick, the smaller the I value, and the more it is thin, the bigger the I value. And a complex distribution of strip tension was controlled, for example, not only a pocket wave but also a simple center wave and edge wave. Because the tension deviation is larger at acceler- ation speed and decelerationspeed than steady speed, AFC system of contact type is better to adopt over 50m/mim. AFC system reduces rapidly large flatness deviation. The maximum I value of strip has been decreased to 13 I, and sticker, defects caused by poor flatness, have been decreased about 60%.

• Nutrition Research and Practice
• /
• 제16권sup1호
• /
• pp.47-56
• /
• 2022

This paper examines the process and evidence used to create the Dietary Reference Intake (DRI) of alpha-linolenic acid (ALA) and eicosapentaenoic acid (EPA) + docosahexaenoic acid (DHA) for Koreans. ALA (18:3n3) is an essential fatty acid, and EPA and DHA are known to have beneficial effects on cardiovascular disease risk and reduction of triglyceride levels. Various international organizations have suggested dietary recommendations for n-3 polyunsaturated fatty acids (PUFAs), including ALA, EPA, and DHA. A DRI for Koreans was established for the first time in 2020, specifically for the adequate intake (AI) of ALA and EPA + DHA. This recommendation was based on the average intake of ALA and EPA + DHA from the Korea National Health and Nutrition Examination Survey 2013-2017. For Korean infants, the AI of ALA and DHA was based on the fatty acid composition of maternal milk. Estimated average requirement and a tolerable upper intake level have not been set for n-3 PUFA due to insufficient evidence. In addition, the intake level of n-3 PUFA for prevention of chronic disease has also not been determined. Future studies and randomized controlled trials are required to establish the UL and to define the level for disease prevention.

• 공학기술논문지
• /
• 제5권4호
• /
• pp.349-353
• /
• 2012

Recently, Mobile multimedia equipments as smart phone and tablet pc requirement is increasing and this market is also being expanded. These mobile equipments require large multi-media function, so more power consumption is required. For these reasons, the needs of power management IC as switching type dc-dc converter and linear regulator have increased. DC-DC buck converter become more important in power management IC because the operating voltage of VLSI system is very low comparing to lithium-ion battery voltage. There are many people to be concerned about digital DC-DC converter without using external passive device recently. Digital controlled DC-DC converter is essential in mobile application to various external circumstance. This paper proposes the DC-DC Buck Converter using the AVR RISC 8-bit micro-processor control. The designed converter receives the input DC 18-30 [V] and the output voltage of DC-DC Converter changes by the feedback circuit using the A/D conversion function. Duty ratio is adjusted to maintain a constant output voltage 12 [V]. Proposed converter using the micro-processor control was compared to a typical boost converter. As a result, the current loss in the proposed converter was reduced about 10.7%. Input voltage and output voltage can be displayed on the LCD display to see the status of the operation.

• 한국농림기상학회지
• /
• 제11권2호
• /
• pp.61-71
• /
• 2009

최근 우리나라의 춥지 않은 겨울은 온대낙엽과수의 휴면타파에 필요한 저온기간을 충분히 갖지 못하게 함으로서 개화시기를 앞당기거나 불균일하게 함으로써 수확량을 감소시키는 원인이 되고 있다. 기후변화시나리오에 의하면 이러한 피해가 앞으로 더욱 심해질 것으로 전망되므로 과수산업의 대응전략마련을 위해 정확한 개화기 예측이 필수적이다. 기존의 개화기 예측은 이른 봄부터 나타나는 기온의 영향만을 적용한 것으로써 겨울 동안 눈의 휴면상태와 봄철 발아로 인한 개화시기의 변동은 반영할 수가 없었다. 본 연구는 휴면기간 동안 시간과 기온의 조합인 온도시간에 근거하여 내생휴면해제일, 발아, 개화를 예측할 수 있는 휴면시계모형을 배 품종 '신고'에 맞게 조정하고자 수행하였다. 매일의 기온 자료만으로 내생휴면해제일을 찾아내기 위해 수확이 끝난 포장에서 매주 신고 가지를 채취하여 발아실험을 수행하였으며 포장에서 관측된 일 최고 및 최저기온을 이용하여 내생휴면해제일까지 온도시간을 계산하고 적산하였다. 기준온도를 $4^{\circ}C$에서 $10^{\circ}C$ 범위로 설정하고 $0.1^{\circ}C$ 단위까지 세분화하여 휴면시계모형을 반복 구동함으로써 출력된 예상 발아기와 실측 발아기가 일치하는 조건에 해당하는 기준온도와 저온요구도를 도출하였다. 장기 생물계절 관측자료에 근거하여 발아 이후 개화에 이르는 기간의 온도시간을 계산하여 휴면시계모형에 추가함으로써 배 품종 신고의 만개기를 예측할 수 있도록 수정하였다. 이 모형에 의해 최근 9년간 개화기를 추정한 결과 RMSE가 1.9일로서 신고의 만개기 예측에 실용화 할 수 있을 것으로 판단된다.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2008년도 제33회 펄프종이기술 국제세미나
• /
• pp.47-70
• /
• 2008

Cost efficiency is today the primary requirement in the paper and board industry. This has led therefore, to a greater preponderance of products with specifically designed functionality to take account of current industry needs. Continually increasing machine coating speeds together with these new coating colour components have put more emphasis on the importance of the correct rheology and water retention of the coating colours to achieve good runnability and end product quality. In the coating process, some penetration of the aqueous phase, to the base paper or board must occur to anchor the pre-coating to the base or the topcoat to the pre-coat. The aqueous phase acts as a vehicle not only for the binder, but also for the other components. If this water or material penetration is not controlled, there will be excessive material shift from the coating colour to the base, before immobilization of the coating colour will stop this migration. This can result in poor machine runnability, unstable system and uneven coating layer, impacting print quality. The performance of rheology modifiers or thickeners on the coating color have tended to be evaluated by the term, "water retention". This simple term is not sufficient to explain their performance changes during coating. In this paper we are introducing a new concept of "material retention", which takes note of the total composition of the coating colour material and therefore goes beyond the concept of only water retention. Controlled material retention leads to a more uniform z-directional distribution of coating colour components. The changes that can be made to z-directional uniformity will have positive effects on print quality as measured by surface strength, ink setting properties, print gloss, mottling tendency. Optical properties, such as light scattering, whiteness and light fastness delivery should also be improved. Additionally, controlled material retention minimizes changes to the coating colour with time in re-circulation giving less fluctuation in quality in the machine direction since it more closely resembles fresh coating for longer periods. Use of the material retention concept enables paper and board producers to have more stable runnability (i.e. lower process costs), improved end product quality (i.e. better performance of used chemicals) and/or optimized use of coating colour components (i.e. lower total formulation cost)

• 한국항행학회논문지
• /
• 제28권3호
• /
• pp.348-355
• /
• 2024

원전해체 시 대용량 처분시스템을 구동하거나 운영 중 제어봉 구동장치 제어시스템과 같은 대규모 측정전류를 요하는 중요설비를 측정 및 테스트하기 위해서는 측정 매체로서 안정적으로 전류를 공급할 수 있는 전류원이 필요하다. 그러나, 흔히 말하는 전원공급기는 전압원으로서 전압만을 내기 때문에 측정부하에 관계없이 일정한 전류를 공급할 수 있는 전류원 역할을 하지 못한다. 전류원은 전압원과 달리 제품을 만들기가 쉽지 않다. 원전 부품의 전류-전압 변환시험과 같은 건전성을 평가하기 위해서는 정상전류치보다 몇십배 훨씬 큰 수십 mA나 암페어 수준의 전류를 인가하여 테스트를 수행해야 하기 때문에 암페어(ampere) 단위의 전류를 공급할 수 있는 전류원이 필수적이다. 따라서 본 개발품에서는 이러한 필요에 의하여 입력이 전압으로 나타나는 전압원을 이용하여 측정대상에 원하는 전류를 일정하게 공급할 수 있는 전압제어으로서 대용량 전류를 공급할 수 있는 직류전압제어 대전류원을 개발하였다. 개발된 제품의의 신뢰성을 확인하기 위하여 원전에서 사용되는 실제의 데이터값을 적용하여 테스트하였으며, 그 결과를 분석하여 선택회로의 정당성을 입증하였다.