• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1056-1059
• /
• 1996

In this paper, we analyzed the effect of the change of the rotor time constant on the performance of the indirect vector control system. By employing indirect field orientation technique, we have also suggested an optimal control algorithm that allows an induction motor to maintain the maximum torque under the changing environment of rotor time constant. A computer simulation on the transient response of the output torque was demonstrated. To verify the validity of the method that has been proposed in this paper, an experiment has been performed utilizing TMS32OC31(40MHz) DSP chip which is capable of performing floating-point arithmetic in real time.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.225-229
• /
• 1998

If there is a mismatch between the controller programmed rotor time constant and the actual time constant of motor, the decoupling between the flux and torque is lost in an indirect rotor field oriented control. This paper presents a new estimation scheme for rotor time constant using artificial neural networks. The parameters of induction motor model organize 2 layer neural to be weight between neuron, which is proposed new in this paper. This method makes networks simple, so its brings not only the improvement in speed but simplification in calculation. Furthermore, it is possible to estimated rotor time constant real time through on-line learning without using off-line learning. The digital simulation and the experimental results to verify the effectiveness of the new method are described in this paper.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.352-356
• /
• 1998

This paper is a study about Ac servo motor position and speed control characteristics which depend on feedforward control, the acceleration / deceleration time constant after the interpolation, and PI control, automatic deceleration at corner in order to shape cutting control of feed drive system of the machine tool. The shape error caused by delay of the servo system in the direction of radius at the time of circular cutting is reduced by feedforward control. The shape error generated by the position command delay is minimized by using the acceleration / deceleration time constant after the interpolation. The results were verified to optical machining center experimentation of the machine tool.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.295-298
• /
• 1996

In this paper, a self-tuning optimal control algorithm is proposed to retain the optimal performance of an active suspension system, when the vehicle has some time varying parameters and parameter uncertainties. We consider a 2 DOF time-varying quarter car model which has the parameter variation of sprung mass, suspension spring constant and suspension damping constant. Instead of solving algebraic riccati equation on line, we propose a neural network approach as an alternative. The optimal feedback gains obtained from the off line computation, according to parameter variations, are used as the neural network training data. When the active suspension system is on, the parameters are identified by the recursive least square method and the trained neural network controller designer finds the proper optimal feedback gains. The simulation results are represented and discussed.

• 전력전자학회논문지
• /
• 제4권2호
• /
• pp.201-208
• /
• 1999

본 논문에서 회전자 시정수 변화에 따른 벡터제어 시스템의 성능저하에 대하여 고찰하고, 동기좌표계의 탄젠트 토크각과 정지좌표계의 탄젠트 토크각의 일치 관계를 이용하여 온라인으로 회전자 시정수의 변화를 추정하는 알고리즘을 제안한다. 제안한 알고리즘의 타당성을 검토하기 위하여 컴퓨터 시뮬레이션 및 실험을 수행하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.11-16
• /
• 1998

In this paper, simultaneous estimation of rotor speed and time constant for a voltage source inverter (VSI) fed induction motor drive are disccussed. The theory is based on the Model Reference Adaptive System (MRAS). The identifier executes Simultaneous rotor speed and time constant so that vector control of the induction may be achieved in the rotor-flux oriented reference frame. Furthermore, to eliminate the offset error caused by the change in the stator resistance, a fuzzy resistance regulator is also designed which operates in parallel with the rotor speed and time constant identifier

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제19권3호
• /
• pp.327-364
• /
• 2015

In this paper, a generalized guidance law with an arbitrary pair of guidance coefficients for impact angle control is proposed. Under the assumptions of a stationary target and a lag-free missile with constant speed, necessary conditions for the guidance coefficients to satisfy the required terminal constraints are obtained by deriving an explicit closed-form solution. Moreover, optimality of the generalized impact-angle control guidance law is discussed. By solving an inverse optimal control problem for the guidance law, it is found that the generalized guidance law can minimize a certain quadratic performance index. Finally, analytic solutions of the generalized guidance law for a first-order lag system are investigated. By solving a third-order linear time-varying ordinary differential equation, the blowing-up phenomenon of the guidance loop as the missile approaches the target is mathematically proved. Moreover, it is found that terminal misses due to the system lag are expressed in terms of the guidance coefficients, homing geometry, and the ratio of time-to-go to system time constant.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.308-311
• /
• 2001

Most of the battery charger for electric powered forklift truck are controlled by the method of 3-phased constant current and constant voltage. However, these chargers have several disadvantages like a large charger capacity, and a short battery life time. This paper presents a digital type battery charger based on multi-mode control adding a constant power control and several assistant controls in the conventional control. The whole control system is performed by a low cost one-chip micro-controller and completely digitize. So we can get a high precision control and a good reliability.

• 한국안전학회지
• /
• 제31권5호
• /
• pp.28-34
• /
• 2016

When a electric power cable is installed in the air for newly or exchanged working, it is necessary at all time to hold a constant tension for an overhead power cable. And also a pendanted power cable is an extreme job to have work in a high sky. For this reason, the objective of this paper developments working robot for preventing disaster that tension of cable installed automatically power cable to hold a constant. So the working robot works at all the time two tasks for mobil and tension it come into a inference between two tasks, control is difficult. Control methode needs to suppress inference of two tasks. In this paper, for installation of overhead power cable, the scheme and control methode of working robot is presented. the robot work at a same time tow tasks that have hold a constant tension of the power cable and move a constant place while unfasten a winding cable at a drum on a chassis. Working robot consist of three parts with mobile system, tension system and control part. As it is applied the feedback/feedforward control, methode of hybrid control is established to suppress that interference come into between two tasks. The simulation programs is made out using models of mobil and tension system, and a proposed controllers. In accordance with simulation, the model of each systems is discussed to make out proper. And also parameters of controllers is selected a suitable value and the driving performance of robot is evaluated.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.325-329
• /
• 1998

This paper describes the controller for the improving speed control of the AC servo motor. The microprocessor provides an output to the difference in command. the servo system improves the characteristics of speed control. When the motor is running at the same speed as set by the reference signal, the speed encoder also provides a signal of the same frequency. Thus, the microprocessor controlled digital techniques enable to realize the flexible performance and control which was possible with time constant of linear acceleration/deceleration. We can know that optimal speed of machining center is 75msec in 30000mm/min and actually, 75msec is using on machining center. Finally experimental results prove excellent performance of this control system. This can be reduced error with more exact measure of actual speed. The system can be adaptable to CNC machine.