• 한국세라믹학회지
• /
• 제39권1호
• /
• pp.86-91
• /
• 2002

고체 산화물 연료전지(Solid Oxide Fuel Cell; SOFC)는 무공해 청정에너지원으로서 기존의 발전방식을 대체할 차세대 에너지원으로 각광받고 있다. 고체산화물 연료전지의 구성요소는 크게 음극(anode), 양극(cathode), 전해질(electolyte)로 나뉘어 지는데 그 중 음극은 전극으로서의 역할은 물론 음극지지형인 경우 지지체 역할가지 수행해야 하기 때문에 아주 다양한 특성이 요구되어지고 있다. 그 중에서도 연료전지 성능의 최대 감쇄요인으로 지적되고 있는 분극저항을 줄이기 위해서는 높은 전기전도도와 높은 가스투과도가 요구되고있다. 본 연구에서는 음극 제조과정 중 첨가하는 기공 전구체의 종류에 따라 기판의 기공구조가 어떻게 바뀌는지 또 그로 인해 기판의 미세구조 및 전기전도도가 어떠한 영향을 받는지 관찰하였다. 결과 음극기판의 미세구조 및 전기전도도는 기공전구체의 종류에 따라 크게 달라졌으며 특히 이방성을 가지는 기공전구체의 사용은 전도성상의 단락 및 비효율적인 기공의 양산을 가져와 결과적으로 연료전지 성능을 악화시킬 것으로 예상된다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권12호
• /
• pp.673-678
• /
• 2000

The dielectric barrier discharge(DBD) is a common method to create a nonthermal plasma in which electrical energy is used to create electrons with a high average kinetic energy. The unique aspect of dielectric barrier discharges is the large array of short lifetime(10ns) silent discharges created over the surface of the dielectric. A silent discharge is generated when the applied voltage exceeds the breakdown voltage of the carrier gas creating a conduction path between the applied electrode and grounded electrode. As charge accumulates on the dielectric, the electric field is reduced below the breakdown field of the carrier gas and the silent discharge self terminates preventing the DBD cell from producing a thermal arc. In fact, the most significant application of dielectric barrier discharges is to generate ozone for contaminated water treatment. Therefore, experiments were perfomed at 1∼2[bar] pressure using a coaxial geometry single dielectric barrier discharge for ozone concentrations and energy densities. The main result show that the concentration and efficiency of ozone are influenced by gas nature, gas quantity, gas pressure, supplied voltage and frequency.

• 한국전기전자재료학회논문지
• /
• 제30권5호
• /
• pp.331-337
• /
• 2017

Thermal batteries, reserve power source, is activated by melting of molten salt at the temperature range of $350{\sim}550^{\circ}C$. To immobile the molten state electrolyte when the thermal battery is activated, the binder must be added in electrolyte. Usually, molten salts include 30~40 wt% of MgO binder to ensure electrical insulation as well as safety. However, the conventional MgO binder tends to increase ionic conductive resistance and thus the inclusion of the binder increases the total impedance of the battery. This paper mainly focused on the study of yttria stabilized zirconia (YSZ) as an alternative binder for molten salt. The chemical stability between the molten salt and YSZ is measured by XRD and DSC. And the sufficient path for ionic conduction on molten salt could be confirmed by the enhanced wetting behavior and the enlarged pore size of YSZ. The electrochemical properties were analyzed using single cell tests so that it showed the outstanding performance than that using MgO binder.

• 대한기계학회논문집B
• /
• 제33권10호
• /
• pp.820-826
• /
• 2009

The anisotropic phonon conductions with varying Joule heating rate of the silicon film in Silicon-on-Insulator devices are examined using the electron-phonon interaction model. It is found that the phonon heat transfer rate at each boundary of Si-layer has a strong dependence on the heating power rate. And the phonon flow decreases when the temperature gradient has a sharp change within extremely short length scales such as phonon mean free path. Thus the heat generated in the hot spot region is removed primarily by heat conduction through Si-layer at the higher Joule heating level and the phonon nonlocality is mainly attributed to lower group velocity phonons as remarkably dissimilar to the case of electrons in laser heated plasmas. To validate these observations the modified phonon nonlocal model considering complete phonon dispersion relations is introduced as a correct form of the conventional theory. We also reveal that the relation between the phonon heat deposition time from the hot spot region and the relaxation time in Si-layer can be used to estimate the intrinsic thermal resistance in the parallel heat flow direction as Joule heating level varies.

• Journal of Welding and Joining
• /
• 제33권6호
• /
• pp.60-66
• /
• 2015

Molten zone shape of pulse laser welding is affected by welding conditions such as beam power, beam speed, irradiation time, pulse frequency, etc. and is divided into conduction type and keyhole type. It is necessary to design heat source model for irradiation of laser beam in the pulse laser welding. Shape variables and the maximum energy density value of the heat source model are different depending on the molten zone shape. In this paper, pulse laser welding simulation for joining of cylindrical part and circular cover was carried out. The heat source model for pulse laser beam with circular path was applied to the heat input boundary condition, radiative and conductive heat transfer were considered for the thermal boundary condition. For each phase, thermal and mechanical properties according to temperature were also applied to analysis. Analytical results were in good agreement with the molten zone size of specimen under the same welding conditions. So, the reliability of the welding simulation was verified. Finally, the improvements for reducing residual deformation after cover welding could be reviewed analytically.

• 마이크로전자및패키징학회지
• /
• 제21권3호
• /
• pp.63-66
• /
• 2014

본 연구에서는 3차원 적층 집적회로 구조에서 Cu TSV를 활용한 열관리 가능성에 대해 살펴보았다. Cu TSV가 있는 실리콘 웨이퍼와 일반 실리콘 웨이퍼 후면부를 점열원을 이용하여 가열한 후 전면부의 온도 변화를 적외선 현미경을 이용하여 관찰하였다. 일반 실리콘 웨이퍼의 경우 두께가 얇아지면서 국부적인 고온영역이 관찰됨으로서 적층 구조에서 층간 열문제의 가능성을 확인할 수 있었다. TSV 웨이퍼의 경우 일반 실리콘 웨이퍼보다 넓은 영역의 고온 분포를 나타내었으며, 이는 Cu TSV를 통한 우선적인 열전달로 인한 것으로 적층 구조에서 Cu TSV를 이용한 효과적인 열관리의 가능성을 나타낸다.

• 한국환경복원기술학회지
• /
• 제20권5호
• /
• pp.67-81
• /
• 2017

Because of lack of accurate understanding of the mechanism of urban heat island (UHI) phenomenon and lack of scientific discussion, it is hard to come up with effective measures to mitigate UHI phenomenon. This study systematically described the UHI and suggested the solutions using green-infrastructure (green-infra). The factors that control UHI are very diverse: radiant heat flux, latent heat flux, storage heat flux, and artificial heat flux, and the air temperature is formed by the combination effect of radiation, conduction and convection. Green-infra strategies can improve thermal environment by reducing radiant heat flux (the albedo effect, the shade effect), increasing latent heat flux (the evapotranspiration effect), and creating a wind path (cooling air flow). As a result of measurement, green-infra could reduce radiant heat flux as $270W/m^2$ due to shadow effect and produce $170W/m^2$ latent heat flux due to evaporation. Finally, green-infra can be applied differently on the macro(urban) scale and micro scale, therefore, we should plan and design green-infra after the target objects of structures are set.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권3호
• /
• pp.161-166
• /
• 1999

We investigate the device characteristics of the separated shorted-anode LIGBT (SSA-LIGBT), which suppresses effectively the negative differential resistance regime, by 2-dimensional numerical simulation. The SSA-LIGBT increases the pinch resistance by employing the highly resistive n-drift region as an electron conduction path instead of the lowly resistive n buffer region of the conventional SA-LIGBT. The negative differential resistance regime of the SSA-LIGBT is significantly suppressed as compared with that of the conventional SA-LIGBT. The SSA-LIGBT shows the lower forward voltage drop than that of the conventional SA-LIGBT.

• 반도체디스플레이기술학회지
• /
• 제10권4호
• /
• pp.37-42
• /
• 2011

In this paper, novel carbon nanotube (CNT)-filled Solderable electrically conductive adhesive (ECA) and joining process have been developed. To investigate the bonding characteristics of CNT-filled Solderable ECA, three types of Solderable ECAs with different CNT weight percent (0, 0.1, 1wt%) were formulated. For a joining process, the quad flat package (QFP) chip was used. The QFP chip had a size of $14{\times}14{\times}2.7$ mm and a 1 mm lead pitch. The test board had a Cu daisy-chained pattern with 18 ${\mu}m$ thick. After the bonding process, the bonding characteristics such as morphology of conduction path, electrical resistance and pull strength were measured for each formulated ECAs. As a result, the electrical and mechanical bonding characteristics for a QFP joints using CNT-filled ECA were improved about 10% compared to those of QFP joints using ECA without CNT.

• 대한기계학회논문집B
• /
• 제21권10호
• /
• pp.1303-1313
• /
• 1997

A micro-macroscopic analysis on the conduction-controlled directional casting of Al-Cu alloys is performed, in which emphases are placed on the microstructural features. In order to facilitate the solution procedure, an iterative micro-macroscopic coupling algorithm is developed. The predicted results show that the effect of finite back diffusion on the transient solidification process in comparison with the lever rule depends essentially on the initial concentration of an alloy. In the final casting, the eutectic fraction is distributed in an increasing-decreasing-increasing pattern, each mode of which is named the chill, interior and end zones. This nonuniformity per se suffices to justify the necessity of this work because it originates from the combined effects of finite back diffusion and cooling path-dependent nature of the eutectic formation. As the cooling rate is enhanced, not only the influence depths of boundaries narrow, but also the eutectic fractions in the chill and interior zones increase. In addition, it is revealed for the first time that the micro segregation band is formed in response to a sudden change in cooling rate during the directional casting. An increasing change creates an overshooting band in the eutectic fraction distribution, and vice versa.