• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10b
• /
• pp.36-39
• /
• 2003

Due to the strength and biocompatibility requirement, the stainless steel SUS 316L is widely used for trauma internal fixation device. SUS 316L can be hardened and strengthened only by cold work. In this work, the material compression test is performed both in laboratory and computer simulation by a FEM analysis software DEFORM to correlate the hardness to strain. This data is then used for preform design and predict the hardness of the finish bone plate forging. Finally, we compared the hardness between the actual forging and computer analysis results. Although the predicted hardness from computer simulation. is 55HV higher than the final forging sample, we can get good compatibility on the hardening tendency of cold forging.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.2
• /
• pp.231-240
• /
• 2007

This paper presents an advanced modeling and simulation technique applied to DC/DC power electronic converters fed through renewable energy power sources. The distributed generation (DG) system at the Illinois Institute of Technology, which employs a phase-l system consisting of a photovoltaic-based power system and a phase-2 system consisting of a fuel cell based primary power source, is studied. The modeling and simulation of the DG system is done using the generalized state space averaging (GSSA) method. Furthermore, the paper compares the results achieved upon simulation of the specific GSSA models with those of popular computer aided design software simulations performed on the same system. Finally, the GSSA and CAD software simulation results are accompanied with test results achieved via experimentation on both, the PV-based phase-l system and the fuel cell based phase-2 power system.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2005.11a
• /
• pp.171-179
• /
• 2005

Computer virus modeling and simulation research has been conducted with focus on the network vulnerability analysis. However, computer virus generally shows the biological virus characters such as proliferation, reproduction and evolution. Therefore it is necessary to research the computer virus modeling and simulation using Artificial Life. The approach of computer modeling and simulation using the Artificial Life technology Provides the efficient analysis method for the effects on the network by computer virus and the behavioral mechanism of the computer virus. Hence this paper proposes the methodology of computer virus modeling and simulation using Artificial Life, which may be contribute the research on the computer virus vaccine.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1994.03a
• /
• pp.7-34
• /
• 1994

;Recently the sheet forming simulation technology revealed great progress in the sense of practical application in the automotive, electric/electronics and aviation/space industries. The goal of sheet forming simulation is to embedded in the design engineering system which is consisted by the analysis and synthesis modules. This design simulation system predicts the slackness of sheet and estimate the formability, and search the optimum material/forming/structure conditions. This OVER-ALL OPTIMUM DESIGN can be classified as follow; 1. ANALYZING PROCEDURE: Numerical simulation based on nonlinear theories -geometry, material and friction nonlinearities- 2. OPTIMIZATION PROCEDURE: Optimum design based on mathematical programing and AI technologies, those are implemented in CAD/CAM/CAE System - Concurrent Engineering System-. In this paper, four subjects will be discussed; (1) State of arts of computer simulation technologies in Japan. (2)History of sheet forming simulation. (3) Benchmark problems. (4) Future technology in the sheet forming simulation.ation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.126-129
• /
• 2008

This paper concerns the progressive die design for an automotive bracket part aided by the computer simulation in order to eliminate the inferiority such as the crack. The computer simulation of the progressive forming process is utilized in order to investigate cause of the cracks. This paper proposes a new guideline for the die design which modifies intermediate shapes and adds intermediate forming stages in progressive forming process. The effectiveness of the proposed design is verified by the computer simulation. The simulation result shows that the modified die design for the progressive forming process can eliminate the crack and improve quality of the automotive bracket part.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.6
• /
• pp.576-580
• /
• 2013

We investigate the enhanced effects of asymmetry ratio variations of the source and drain area in silicon (Si) field-effect transistor (FET). Photoresponse according to the variation of asymmetry difference between the width of source and drain are obtained by using the plasmonic terahertz (THz) wave detector simulation based on technology computer-aided design (TCAD) with the quasi-plasma 2DEG model. The simulation results demonstrate the potential of Si FETs with asymmetric source and drain structures as the promising plasmonic THz detectors.

• Journal of electromagnetic engineering and science
• /
• v.16 no.1
• /
• pp.1-6
• /
• 2016

Computer simulations were conducted to demonstrate the generation of microwave-induced thermoacoustic signal. The simulations began with modelling an object with a biological tissue characteristic and irradiating it with a microwave pulse. The time-varying heating function data at every particular point on the illuminated object were obtained from absorbed electric field data from the simulation result. The thermoacoustic signal received at a point transducer at a particular distance from the object was generated by applying heating function data to the thermoacoustic equation. These simulations can be used as a foundation for understanding how thermoacoustic signal is generated and can be applied as a basis for thermoacoustic imaging simulations and experiments in future research.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.53-56
• /
• 2007

Computer simulation of microstructure evolution during hot forging process is of great interest in recent years. Recrystallization model and grain growth model which use a phenomenological approach were summarized. For the waspaloy, upsetting process and cogging process were simulated using $DEFORM^{TM}$ and the change in grain size were investigated in each deformation procedure.

• Membrane Journal
• /
• v.30 no.4
• /
• pp.242-251
• /
• 2020

Computer simulation tools mainly used for polymer materials and polymeric membranes are divided into various fields depending on the size of the object to be simulated and the time to be simulated. The computer simulations introduced in this review are classified into three categories: Quantum mechanics (QM), molecular dynamics (MD), and mesoscale modeling, which are mainly used in computational material chemistry. The computer simulation used in polymer research has different research target for each kind of computational simulation. Quantum mechanics deals with microscopic phenomena such as molecules, atoms, and electrons to study small-sized phenomena, molecular dynamics calculates the movement of atoms and molecules calculated by Newton's equation of motion when a potential or force of is given, and mesoscale simulation is a study to determine macroscopically by reducing the computation time with large molecules by forming beads by grouping atoms together. In this review, various computer simulation programs mainly used for polymers and polymeric membranes divided into the three types classified above will be introduced according to each feature and field of use.

• Journal of the Semiconductor & Display Technology
• /
• v.4 no.1 s.10
• /
• pp.23-27
• /
• 2005

This paper presents a simulation methodology for the poly-silicon oriented TCAD(technology-CAD) system. A computer simulation environment for the poly-silicon processing has been set up with the proper adoption of the two-stream model for ion-doping, diffusion, and defects inside of grain and on the grain boundary. After the simulator calibration, simulation results for the poly-silicon diffusion hat shown a good agreement with the SIMS data.