• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.117-120
• /
• 2005

The relationship between strain and applied potential was derived for composite actuators consisting single-wall carbon nanotubes (SWNTs) and conductive polymers (CPs). During deriving the relationship, an electrochemical ionic approach is utilized to formulate the electromechanical actuation of the composite film actuator. The results show that the well-aligned SWNTs composite actuator can give good actuation responses and high actuating forces available. The actuation is found to be affected by both SWNTs and CPs components and the actuation of SWNTs component has two kinds of influences on that of the CPs component: reinforcement at the positive voltage and abatement at the negative voltage. CNT/EAP was fabricated successfully using the chemical polymerization method.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.2
• /
• pp.3-7
• /
• 2008

Vibratory conveyors are widely used in industry to transport granular materials and products. A theoretical point mass model for vibratory conveying was studied. The results agreed well with experimental observations. The model theory included the resting, sliding and flight states of the material. Each state was considered separately when determining the equations of motion. For the coefficients of restitution, values of zero for the normal component and 0.8 for the tangential component were found to be appropriate for modeling the collisions of the granular particles with the conveying surface. The vibration angle had a large influence on the mode and rate of transport. There was an optimum vibration angle for a given set of conditions. The optimum vibration angle decreased and was better defined as the coefficient of friction increased. The results suggest the existence of an optimum dimensionless track acceleration (throw number), which does not support general industrial practice in which the track acceleration is limited when the feed cycle becomes erratic and unstable.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.233-234
• /
• 2015

We present results of a new high-resolution spectroscopic study of the RS CVn-type binary system EI Eridani (HD26337). We used high S/N ratio LSD profiles to measure a new RV orbit of the primary component and new orbital parameters. We found evidence of strong spectral line profile variations at time intervals indicating the existence of short-lived (few days) spots on the surface of the primary component. We measured a projected rotation velocity of star of 53.2 km/s.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.05a
• /
• pp.165-166
• /
• 1994

The depth profiles of the as-grown and the annealed NH$_3$ oxide film in NH$_3$(7.5%)/$N_2$ ambient at 45$0^{\circ}C$ are analized . This annealing in the ambient of mixed gases removes the small quantities of N component from the NH$_3$ oxide film. In AES analysis, the NH$_3$ oxidation shows the exact stoichiometry of SiO$_2$ and a sharp slop at SiO$_2$/Si interface.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.5
• /
• pp.432-435
• /
• 2020

The elasticity tensor for water may be employed to model the fully saturated porous material. Mostly water is assumed to be incompressible with a bulk modulus, however, the upper and lower bounds of off-diagonal components of the elasticity tensor of porous materials filled with water are violated when the bulk modulus is relatively high. In many cases, the generalized Hill inequality describes the general bounds of Voigt and Reuss for eigenvalues, but the bounds for the component of elasticity tensor are more realistic because the principal axis of eigenvalues of two phases, matrix and water, are not coincident. Thus in this paper, for anisotropic material containing pores filled with water, the bounds for the component of elasticity tensor are expressed by the rule of mixture and the upper and lower bounds of fully saturated porous materials are violated for low porosity and high bulk modulus of water.

• International Journal of Computer Science & Network Security
• /
• v.21 no.9
• /
• pp.103-108
• /
• 2021

The emergence of new technologies and their implementation by different manufacturers of electronic devices are experiencing an ascending trend. Most of the time, these protocols are expected to reach a certain degree of maturity, and electronic equipment manufacturers use simplified communication standards and interfaces that have already reached maturity in terms of their development such as ModBUS, KNX or CAN. This paper proposes an IoT solution of the Smart Home type based on an Analysis and Prediction System. A data acquisition component was implemented and there was defined an algorithm for the analysis and prediction of actions based on the values collected from the data update component and the data logger records.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.10
• /
• pp.38-43
• /
• 2021

Photocurable hydrogels are widely used as 3D printing materials in tissue engineering (e.g., scaffold fabrication) as well as optical fibers (or optical sensors) materials. Photocurable hydrogels can control optical and mechanical properties such as chemical or fabrication conditions. In previous research, we introduced a new 3D printing method to fabricate a freestanding overhanging hydrogel structure without supporting structure. This study was measured and analyzed the difference of the mechanical properties of the photocurable hydrogel according to the light intensity using a micro tensile tester. In practically, it was difficult to perform a direct tensile test on a micro (less than 1 mm) size fiber. In this study, the tensile test of the hydrogel fibers could be measured simply and repeatedly using a paper carrier.

• Transactions of Materials Processing
• /
• v.7 no.6
• /
• pp.570-574
• /
• 1998

The texture evolution during deep drawing of AA1050 sheets was experimentally investigated and the lattice rotation rate was predicted using rate sensitive model with full constraints boundary conditions. The measured textures are dependent on the amount of the flange deformation and the initial crystal orientations. In the specimen parallel to RD the initial crystal orientations and the D component rotated toward the Cu component and the initial crystal orientations along the $\alpha$ fiber rotated toward the G {1 1 0}<0 0 1> and P {1 1 0} <1 1 1> components during deep drawing. In the specimen parallel to $45{\circ}$ with respect to RD the initial crystal orientations around the D component rotated about ND and the initial crystal orientations along the ${\alpha}$ fiber also rotated toward the (1 1 0) [2 3] and (1 1 0)[2 7] components about ND. In the specimen parallel to TD. the initial crystal orientations around the D component rotated toward the rotated cube and the initial crystal orientations along the ${\alpha}$ fiber rotated toward the {1 1 0} <1 1 3> component.

• Journal of the Korea Furniture Society
• /
• v.20 no.2
• /
• pp.166-174
• /
• 2009

Most of the furniture in the past was dedicated to its original use such as storage and accommodation of articles or sitting tools, but the concept of furniture in contemporary indoor spaces is gradually increasing in its meaning while exchanging close impacts with other spatial components. Indeed, in contemporary furniture, a component other than furniture constituting a space would sometimes serve the common roles of furniture or sometimes furniture would include all indoor objects used to make people's living more convenient. This study reviewed the meaning of furniture and changes in its roles in contemporary indoor spaces and summarized the characteristics presenting a few examples. First, in contemporary indoor spaces, furniture as an independent object does not having a meaning any more. The fusion of functions with other components constituting indoor spaces is the most important characteristics in contemporary furniture and it has been already attempted in diverse ways through fusion with buildings surpassing fusion with other pieces of furniture or electric home appliances. Second, the arrangement conforming to the roles required by spaces and diverse forms of attempts are essential. Since furniture is an item the most closely related to human residential life, studies on human behaviors in spaces must precede. The efforts to enhance work efficiencies and used limited spaces more efficiently will be continued and explorations of new forms should be also continued. Third, with regards to manufacturing methods, new technologies should be applied more widely and furniture materials must be diversified through the use of new materials including not only cutting-edge new materials but also all the materials that can be applied to furniture such as conventional natural materials and environment friendly materials that can be recycled.

• Particle and aerosol research
• /
• v.18 no.3
• /
• pp.69-77
• /
• 2022

In order to understand the characteristics of fine particles emitted from coal-fired power plant stacks, it is important to analyze the size distribution and components of particles. In this study, particle size distributions were measured using the ejector-porous tube dilution device and an ELPI system at a stack in a coal-fired power plant. Main elemental components of particles in each size interval were also identified through TEM-EDS analysis for the particles collected in each ELPI stage. Particle size distributions based on number and mass were analyzed with component distributions from 0.006 to 10 ㎛. The highest number concentration was about 0.01 ㎛. The main component of the particles consisted of sulfur, which indicated that sulfate aerosols were generated by gas-to-particle conversion of SO2. In a mass size distribution, a mono-modal distribution with a mode diameter of about 2 ㎛ was shown. For the components of PM1.0 (particles less than 1 ㎛), the abundance order was F > Mg > S > Ca, and however, for the components of PM10 (particles less than 10 ㎛), it was in the order of Fe > S > Ca > Mg. The elemental components by particle size were confirmed.